Engineering topics

Garofalo, A. M.

Publications and source records attributed to Garofalo, A. M..

At least 19 records

DOE OSTI2024

Validation study of RWM stability in DIII-D high- β N plasmas

The n = 1 (n is the toroidal mode number) resistive wall mode (RWM) stability is numerically investigated for two DIII-D high-β N discharges 176440 and 172461, utilizing the MARS-F (Liu et al 2000 Phys. Plasmas 7 3681) and MARS-K (Liu et al 2008 Phys. Plasmas 15 112503) codes. Systematic validation efforts are attempted, for the first time, for discharges with very slow or vanishing toroidal flow for a large fraction of the plasma volume. While gaining physics insights in accessing stable operation regime at β N exceeding the Troyon no-wall limit in these slow-rotation experiments, the predictive capability of fluid and non-perturbative magnetohydrodynamic-kinetic hybrid models for the RWM is further confirmed. The MARS-F fluid model, with a strong but numerically tunable viscosity mimicking ion Landau damping of parallel sound waves, finds complete stabilization of the n = 1 RWM in the considered DIII-D plasmas under the experimental flow conditions. Similarly, either full stabilization (for discharge 176440) or marginal stability (for discharge 172461) of the mode is computed by the MARS-K hybrid model, which is first-principle based without free model parameters. In particular, all drift kinetic resonances, including those of thermal and energetic particles, are found to synergistically act to marginally stabilize the RWM in discharge 172461. These MARS-F/K modeling results explain the experimentally observed stable operational regime in DIII-D, as far as the RWM stability is concerned. Extensive numerical sensitivity studies, with respect to the plasma toroidal flow speed as well as the radial location of the resistive wall, are also carried out to further support the validation study.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2024

A high-density and high-confinement tokamak plasma regime for fusion energy

The tokamak approach, utilizing a toroidal magnetic field configuration to confine a hot plasma, is one of the most promising designs for developing reactors that can exploit nuclear fusion to generate electrical energy. To reach the goal of an economical reactor, most tokamak reactor designs simultaneously require reaching a plasma line-averaged density above an empirical limit—the so-called Greenwald density and attaining an energy confinement quality better than the standard high-confinement mode. However, such an operating regime has never been verified in experiments. In addition, a long-standing challenge in the high-confinement mode has been the compatibility between a high-performance core and avoiding large, transient edge perturbations that can cause very high heat loads on the plasma-facing-components in tokamaks. Here we report the demonstration of stable tokamak plasmas with a line-averaged density approximately 20% above the Greenwald density and an energy confinement quality of approximately 50% better than the standard high-confinement mode, which was realized by taking advantage of the enhanced suppression of turbulent transport granted by high density-gradients in the high-poloidal-beta scenario. Furthermore, our experimental results show an integration of very low edge transient perturbations with the high normalized density and confinement core. The operating regime we report supports some critical requirements in many fusion reactor designs all over the world and opens a potential avenue to an operating point for producing economically attractive fusion energy.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Long-pulse high-performance H-mode plasmas achieved on EAST

A record duration of a 310 s H-mode plasma (H 98y2 ~ 1.3, n e /n GW ~ 0.7, f BS > 50%) has been recently achieved on experimental advanced superconducting tokamak (EAST) with metal walls, exploiting the device's improved long-pulse capabilities. The experiment demonstrates good control of tungsten concentration, core/edge MHD stability, and particle and heat exhaust with an ITER-like tungsten divertor and zero injected torque, establishing a milestone on the path to steady-state long-pulse high-performance scenarios in support of ITER and CFETR. Important synergistic effects are leveraged toward this result, which relies purely on radio frequency (RF) powers for heating and current drive (H&CD). On-axis electron cyclotron heating enhances the H&CD efficiency from lower hybrid wave injection, increasing confinement quality and enabling fully non-inductive operation at high density (n e /n GW ~ 70%) and high poloidal beta (β P ~ 2.5). A small-amplitude grassy edge localized mode regime facilitates the RF power coupling to the H-mode edge and reduces divertor sputtering/erosion. The high energy confinement quality (H 98y2 ~ 1.3) is achieved with the experimental and simulated results pointing to the strong effect of Shafranov shift on turbulence. Transport analysis suggests that trapped electron modes dominate in the core region during the record discharge. The detailed physics processes (RF synergy, core-edge integration, confinement properties, etc.) of the steady-state operation will be illustrated in the content. In the future, EAST will aim at accessing more relevant dimensionless parameters to develop long-pulse high-performance plasma toward ITER and CFETR steady-state advanced operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Gyrokinetic simulations of core turbulence and thermal transport in the high-β P discharge on EAST

The properties of core turbulence and thermal transport are investigated for EAST high-β P (β P ~ 3.1) plasmas with dominant electron heating (Te/Ti > 1) via gyrokinetic simulation with the NLT code. Linear simulations identify that the electrostatic η e -driven trapped electron mode (η e -TEM) dominates in the core region (ρ< 0.7) and the ion temperature gradient (ITG) mode dominates in the out region (ρ≥ 0.7), consistent with the linear threshold analysis of micro-instabilities. Sensitivity analysis shows that the normalized electron density gradient (R/L ne ) and ITG (R/L Ti ) are two effective parameters to stabilize TEM instability. Nonlinear simulations are also carried out and compared with the experimental results, which show that the electron thermal internal transport barrier (ITB) in EAST high-β P plasma is determined by the TEM-induced turbulence. A higher zonal flow shearing rate is observed in the ITB region (0.2 < ρ < 0.34), which can regulate energy transport induced by TEM turbulence and facilitate the formation of e-ITB. A plausible positive feedback mechanism to mitigate turbulence transport and improve energy confinement via enhanced ion heating is proposed for future experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Integration of high confinement, high poloidal beta plasma with dual radiated power and detachment controls for divertor protection and ELM suppression

Divertor detachment without serious core confinement quality loss in DIII-D’s high poloidal β scenario has been combined with impurity-induced ELM mitigation without disruption. Use of Ne previously granted access to a detached, non-ELMing regime that retained high confinement quality due to stimulation of Internal Transport Barrier (ITB) growth, but suffered from on-going core fuel dilution and high disruptivity. Excess Ne accumulation in the core plasma has now been avoided by feeding back core radiated power ($P_{rad}$) measurements to control Ne seeding, rather than using attachment fraction ($A_{frac}$) control with Ne; this also reduces disruptivity. At the same time, N 2 seeding is used in a feedback loop with $A_{frac}$ measurements, which previously posed low disruption risk. In this way, the effect of Ne in the core is managed while avoiding excess seeding, and N 2 acts to correct for any excess heat exhaust that might interfere with detachment. The average Ne flow rate was 38% of what was used in pure Ne $A_{frac}$ control, plus average N 2 flow that was 43% of pure N 2 $A_{frac}$ control, even while meeting an even deeper detachment target. Meanwhile, a steep pressure gradient in the core plasma reduces sensitivity to impurity-induced degradation of the pedestal and reasonable confinement quality was maintained despite operational challenges that blocked formation of an ITB in these experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

The role of toroidal rotation in the very high energy confinement quality observed in super H-mode experiments on DIII-D

In this paper, we report the key role that toroidal rotation and the related ExB shear physics played in the very high energy confinement quality (H98y2>1.5) of super H-mode experiments on DIII-D. Experiments show that the energy confinement quality decreases when toroidal rotation decreases due to the decreased externally controlled torque per particle. Meanwhile, the total pedestal pressure in the experiments remains very high during the rotation and confinement quality change. TGYRO transport modeling suggests the contribution from rotation in the ExB shear is responsible for the confinement quality in excess of standard H-mode (H98y2~1). CGYRO gyrokinetic simulations reveal the governing physics in the core plasma of super H-modes: significant up-shift of nonlinear the ITG critical gradient is observed when applying ExB shear physics in the modeling based on experimental data. The effects of other physical parameters and contribution from pedestal height, which may play minor roles in this study, are also discussed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

The high-power helicon program at DIII-D: gearing up for first experiments

Helicon current drive, also called fast wave current drive in the lower hybrid range of frequencies, has long been regarded as a promising current drive tool for reactor grade plasmas. A newly installed MW-level system at DIII-D will be the first test of this technology in reactor-relevant plasmas, in the sense that full single-pass absorption is expected. A 30-module traveling wave antenna has been installed and optimized in-vessel in early 2020. The linear electromagnetic characteristics of the unloaded module array have been extensively tested both on the bench and in the vessel at instrumentation power levels. Excellent performance has been achieved, ~2% reflected power and ~1.5% dissipated power per module in air, in a 10 MHz band around 476 MHz. Stripline feeds on both ends of the antenna allow either co or counter current drive. The installation of a 1.2 MW klystron and associated high-power electronics was completed in Fall 2020. Commissioning of the antenna is ongoing. An important goal of this experiment is to validate the helicon current drive physics basis using an extensive set of new and upgraded diagnostics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

A model investigation of the impact of lower hybrid wave scattering angle on current drive profile in EAST and Alcator C-Mod

Lower hybrid current drive (LHCD) is beneficial for developing a steady-state operation scenario in a tokamak. This paper conducts a modeling investigation to identify an optimum rotation angle of the initial lower hybrid perpendicular (to the background magnetic field $\overrightarrow{B}$) wavevector for best matching the experimental RF current profile. It is hypothesized that central RF power deposition widely observed in the present-day LHCD experiments arises from wave scattering by turbulence. In a standard model without considering such interactions, the predicted power deposition profile is generally broad with off-axis peaking, not in agreement with experimental observations. A heuristic approach is adopted by introducing a spectral broadening mechanism by modifying the initial orientation of the perpendicular wavevector. The ray-tracing/Fokker–Planck solver GENRAY/CQL3D is utilized within the python-based π-scope framework. A focus is given to identify the perpendicular wavenumber orientation angle with respect to the magnetic surface normal vector at the initial ray location. Our modeling study shows that rotating the perpendicular wavevector in such a way as to increase the initial poloidal component is effective in reproducing the centrally peaked current profile observed in normal shear plasmas on both EAST and C-Mod. These waves can readily be absorbed to the central plasma, which reduces the sensitivity of the power deposition profile to a slight change of the plasma condition. The same approach is also found to help broaden the off-axis power deposition profile in a reverse-shear EAST plasma, leading to a better agreement with the experiment. The results presented here suggest that spectral modification arising from edge density fluctuations in a tokamak may need to be considered in understanding wave propagation and absorption. A further experimental and theoretical/modeling study is vital as a reverse approach is adopted in this study. Finally, our work suggests that mitigation or control measures are critical for parasitic effects occurring on the first pass in a reactor regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Theoretical analysis of key factors achieving reversed magnetic shear q-profiles sustained with lower hybrid waves on EAST

The phase space analysis technique is applied to provide new insights into the fully non-inductive lower hybrid current driven (LHCD) discharges on EAST (Garofalo et al 2017 Nucl. Fusion 57 076037). The analysis shows that there are bounded and unbounded topologies of lower hybrid (LH) waves in phase space. For typical parameters on EAST, the propagation domain for 4.6 GHz LH waves is bounded, while unbounded for 2.45 GHz LH waves and one of the conditions is recognized to be good for achieving an off-axis current profile driven by 4.6 GHz LH waves on EAST. The parametric analysis on the potential power deposition (PPD) region for those experiments demonstrates that the reversed magnetic shear dominates the wave behavior, and confines the LH power absorption to the far off-axis region as long as it occurs in the 4.6 GHz dominated LHCD discharge. GENRAY/CQL3D simulations also confirm this effect of reversed shear on the power absorption of 4.6 GHz waves. A bounded propagation domain and a positive feedback loop between magnetic shear reversal and off-axis LHCD profile could explain the LH-only-sustained strong reversed magnetic shear observed in experiments on multiple machines. In contrast, there is no such effect for 2.45 GHz waves on EAST since the PPD region is less sensitive to the change of reversed shear due to the unbounded propagation domain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Observation of fully detached divertor integrated with improved core confinement for tokamak fusion plasmas

Integration of divertor detachment with a high-performance (β N ~ 3, β p > 2, H 98 ~ 1.5) core plasma has been demonstrated in DIII-D high-β p (poloidal beta) plasmas associated with a sustained core internal transport barrier (ITB) and an H-mode edge transport barrier (ETB). Such good core-edge integration has been achieved for both neon and nitrogen seeding, for both favorable and unfavorable B-field directions, independently from the impurity puffing locations, though these variations play important roles on divertor characteristics. Compared to the standard H-mode plasmas, the high-β p plasma exhibits a much wider window of detachment compatible with high confinement core. Fully detached divertor plasmas with low plasma temperature (Te < 5 eV), low particle flux, and low heat flux across the entire divertor target plate were obtained by using nitrogen seeding. This detached high-β p plasma is compatible with a newly developed detachment control system which can help optimize the nitrogen gas flow rate. Several features, i.e., the high edge safety factor in the high-β p scenario, impurity injection, closed divertor and reduced heating power requirement due to the high confinement, facilitate the achievement of full divertor detachment at lower density. Instead of degrading global performance, the divertor detachment facilitates the access to an even stronger ITB at large radius with a relatively weak ETB through self-organized synergy between ITB and ETB, leading to sustained high confinement. The strengthening of the large-radius ITB compensates for the ETB degradation associated with divertor detachment. In addition, a weak ETB naturally has smaller edge localized modes (ELMs). In particular, with neon injection, a long-period no-ELM H-mode phase has been achieved simultaneously with high-performance core and partially detached divertor plasmas. Furthermore, these results demonstrate the possibility of integrating excellent core plasma performance with an effective divertor solution, an essential step toward steady-state operation of reactor-grade plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

On the very high energy confinement observed in super H-mode DIII-D experiments

Analysis of recent super H-mode experiments on DIII-D shows that high rotation, not high pedestal, plays the essential role in achieving very high conﬁnement H98y2 > 1.5. Very high conﬁnement is reached early on in the H-mode phase of these discharges, when the pedestal is still very low, but after the toroidal rotation has already built-up to very high levels in the core. As the discharge evolves, the rotation drops, and so does the energy conﬁnement, despite a sustained very high pressure pedestal. During this evolution, the conﬁnement quality is linearly correlated with the core toroidal rotation, which varies according to diﬀerent levels of injected neutral beam torque per particle. Core transport modeling shows that the contribution from rotation in the E×B shear is responsible for conﬁnement quality signiﬁcantly in excess of standard H-mode (H98y2 ∼ 1).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Advances in physics understanding of high poloidal beta regime toward steady-state operation of CFETR

Experimental and modeling investigations of the high βp scenarios on the DIII-D and EAST tokamaks show advantages in high energy confinement, avoidance of n = 1 MHD, and core-edge integration with reduced heat flux, making this scenario an attractive option for CFETR steady-state operation. Experiments show that plasmas with high confinement and high density can be achieved with neutral beam injection on DIII-D (β p ~ 2.2, β N ~ 3.5, f BS ~ 50%, f Gw ~ 1.0, H 98y2 ~ 1.5) and pure RF power on EAST (β P ~ 2.0, β N ~ 1.6, f BS ~ 50%, f Gw ~ 0.8, H 98y2 > 1.3). By tailoring the current density profile, a q-profile with local (off-axis) negative shear is achieved that yields improved confinement and MHD stability. Transport analysis and simulation suggest that the combination of high density gradient and high Shafranov shift allows turbulence stabilization and higher confinement. Using on-axis ECH injection, tungsten accumulation is avoided on EAST, and this is reproduced in modeling. Reduced heat flux (by >40%) and maintenance of high core confinement is achieved with active feedback control of the radiated divertor, an important result for long pulse operation in tokamaks. In conclusion, the improved physics understanding and validated modeling tools are used to design a 1GW steady-state scenario for CFETR.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Progress of Divertor Heat and Particle Flux Control in EAST for Advanced Steady-State Operation in the Last 10 Years

Active control of the excessively high heat and particle fluxes on the divertor target plates is of fundamental importance to the steady state operation of tokamaks, especially for fusion reactors. A series of experiments have been carried out on this critical issue to relieve the plasma-wall interactions in the experimental advanced superconducting tokamak (EAST) in the last ten years, not only contributing to the long pulse operation of EAST itself, but also providing physical understandings and potential techniques to the next-generation devices like ITER. Here we have characterized the power deposition pattern and broadened the divertor footprint width effectively. The plasma-wetted area is actively handled using either 3-dimentional edge magnetic topology or advanced plasma equilibrium, thereby peak heat flux around the strike point is reduced. Active control of detachment or radiation compatible with core plasma performance has progressed significantly in very recent years, with a series of active feedback control modules developed and utilized successfully, based on the divertor physics advances with both experiments and simulation. The upper divertor of EAST was upgraded from graphite to active water-cooling ITER-like tungsten in 2014, exhibiting much enhanced heat removal capability. As for the particle exhaust including both fueling and impurity particles, in addition to wall conditioning and impurity source control, the efficiency of particle flux exhaust is optimized by making full use of the divertor closure and the plasma drifts in both scrape-off layer and divertor volume. These heat and particle exhaust advances contribute greatly to a series of EAST achievements like H-mode operation over 100 s. A brief near-term plan on the integrated control of divertor plasma-wall interactions in long-time scale will also be introduced, aiming to provide favorable divertor operation solution for ITER and CFETR.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Role of microtearing mode in DIII-D and future high- β p core plasmas

This paper provides modeling evidence for a new variant of microturbulence instability that regulates the electron thermal fluxes in the transport barrier region of DIII-D "high β p " discharges. This scenario is being investigated as a possible scenario for future steady-state reactors, and thus it is essential to understand the physics processes which govern its performance in order to confidently extrapolate to future devices. Additional analysis examining the extrapolation of this scenario to ITER shows that while the new microtearing mode identified here is unlikely to be unstable in that regime (due to increased temperatures and reduced collisionality), the large shift in magnetic axis (Shafranov shift) that arises in these plasmas may still favor stabilization of common ballooning instabilities which peak on the low field side, but destabilize electrostatic slab modes on the high field side.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2021

Integration of full divertor detachment with improved core confinement for tokamak fusion plasmas

Divertor detachment offers a promising solution to the challenge of plasma-wall interactions for steady-state operation of fusion reactors. Here, we demonstrate the excellent compatibility of actively controlled full divertor detachment with a high-performance (β N ~ 3, H 98 ~ 1.5) core plasma, using high-β p (poloidal beta, β p > 2) scenario characterized by a sustained core internal transport barrier (ITB) and a modest edge transport barrier (ETB) in DIII-D tokamak. The high-β p high-confinement scenario facilitates divertor detachment which, in turn, promotes the development of an even stronger ITB at large radius with a weaker ETB. This self-organized synergy between ITB and ETB, leads to a net gain in energy confinement, in contrast to the net confinement loss caused by divertor detachment in standard H-modes. These results show the potential of integrating excellent core plasma performance with an efficient divertor solution, an essential step towards steady-state operation of reactor-grade plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Grassy ELM regime at low pedestal collisionality in high-power tokamak plasma

Spontaneous mitigation of giant ELMs and appearance of grassy ELMs have been observed repeatedly at low pedestal collisionality (${\nu }_{\mathrm{e},\mathrm{p}\mathrm{e}\mathrm{d}}^{{\ast}}\sim 0.15$) in the high-power (P inj > 13 MW) hybrid scenario in DIII-D. Higher β p and higher q 95 appear to be beneficial to achieving the grassy ELM regime. The grassy ELM H-mode plasma shows high energy confinement performance (H 98y2 up to over 1.5) under the conditions of high neutral beam torque and high core rotation. The pedestal width appears to exceed the EPED1.0 model prediction by more than 50%. Pedestal stability analysis performed with the ELITE code indicates that the stability against low-n kink/peeling modes is improved with increased auxiliary heating power and the operational point in the grassy ELM regime is located near the ballooning boundary. The pedestal stability characteristics during the grassy ELM crashes have been investigated in comparison with the giant ELM crashes based on plasma profiles experimentally measured with high resolution and accuracy. It has been found that the underlying mechanism for the observed small-amplitude ELM crashes is mainly the expansion of the ballooning stability boundary induced by an initial radially localized collapse in the pedestal, which helps to stop the growth of instabilities and further collapse of the pedestal. The effect of electron density pedestal on mitigating edge localized instabilities has been analyzed by numerical simulation, suggesting that the electron density pedestal characterized by high n e,sep /n e,ped and low density gradient helps to stabilize peeling-ballooning modes because of a low pressure pedestal gradient and to lower the ballooning boundary mainly because of a low ion diamagnetic frequency in the pedestal region, thus triggering ballooning instabilities and producing the intrinsic grassy ELMs. Numerical simulation of the Chinese fusion engineering test reactor (CFETR) with the SOLPS code indicates that the separatrix density might be insensitive to the electron diffusivity in the pedestal region and increase with the power flowing from the core region to the edge region. Furthermore, pedestal stability analysis suggests that the flat density pedestal with high separatrix density obtained in the high-power plasma in CFETR would make the operational point close to the ballooning boundary, which is considered to help destabilize ballooning instabilities and facilitate the access to the grassy ELM regime.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Magnetic shear effect on plasma transport at T e / T i ~ 1 through electron cyclotron heating in DIII-D plasmas

The effect of magnetic shear on plasma transport for an electron to ion temperature ratio ( T e / T i ) near unity has been explored in DIII-D utilizing electron cyclotron heating (ECH). Previous reports showed that significant confinement degradation occurred at T e / T i ~ 1 in positive shear (PS) plasmas in DIII-D, whereas reduced confinement degradation was observed in negative central shear (NCS) plasmas. In this study, plasma transport in weak magnetic shear (WS) plasmas with ECH is investigated and compared with that in NCS and PS plasmas. Here the magnetic shears ($\hat s$) are $\hat s$ > 0.5, ~0 and <-0.1 in the core region (ρ~ 0.3–0.4) of PS, WS and NCS plasmas, respectively, and flat or negative inside ρ~ 0.4 in the WS and NCS plasmas. Weak magnetic shear is found to be effective in minimizing degradation of ion thermal confinement as T e / T i increases through ECH application, and an improved confinement factor of H 98y2 ~ 1.2 is maintained, similar to NCS plasmas. At T e / T i ~ 1, the ion thermal diffusivity around an internal transport barrier decreases when changing the magnetic shear from positive to weak or negative shear. Also, reduced local particle and momentum transport was indicated by steeper density and toroidal rotation profiles in the weak and negative shear regimes. Linear gyrokinetic simulations predict little change in growth rates of low-k turbulence with ECH application in the WS and NCS plasmas, which is consistent with the transport and profile analyses.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2020

Progress in extending high poloidal beta scenarios on DIII-D towards a steady-state fusion reactor and impact of energetic particles

To prepare for steady-state operation of future fusion reactors (e.g. the International Thermonuclear Experimental Reactor and China Fusion Engineering Test Reactor (CFETR)), experiments on DIII-D have extended the high poloidal beta ( β P ) scenario to reactor-relevant edge safety factor q 95 ~ 6.0, while maintaining a large-radius internal transport barrier (ITB) using negative magnetic shear. Excellent energy confinement quality ( H 98y2 > 1.5) is sustained at high normalized beta ( β N ~ 3.5). This high-performance ITB state with Greenwald density fraction near 100% and q min ≥ 3 is achieved with toroidal plasma rotation V tor ~ 0 at ρ ≥ 0.6. This is a key result for reactors expected to have low V tor . At high β P (≥1.9), large Shafranov shift can stabilize turbulence leading to a high confinement state with a low pedestal and an ITB. At lower β P (<1.9), negative magnetic shear in the plasma core contributes to turbulence suppression and can compensate for reduced Shafranov shift to continue to access a large-radius ITB and excellent confinement with low V tor , consistent with the results of gyrofluid transport simulations. These high- β P cases are characterized by weak/no Alfvén eigenmodes (a.e.) and classical fast-ion transport. At high density, the fast-ion deceleration time decreases and Δ β fast is lower; these reduce a.e. drive. The reverse-shear Alfvén eigenmodes are weaker or stable because the negative magnetic shear region is located at higher radius, away from the peaked fast-ion profile. Resistive wall modes can be a limitation at simultaneous high β N , low internal inductance, and low rotation. Analysis suggests that additional off-axis external current drive could provide a more stable path at reduced q 95 . Based on a DIII-D high- β P plasma with large-radius ITB, two scenarios are proposed for CFETR Q = 5 steady-state operation with ~1 GW fusion power: a lower-$l_i$($l_i$ ~ 0.66) and a higher-$l_i$($l_i$ ~ 0.75) case. Using a Landau closure model, multiple energetic particle (EP) effects on the a.e. stability are analyzed modifying the growth rate of the a.e.s triggered by the neutral-beam-injection EPs and alpha particles, although the stabilizing/destabilizing effect is weak for the cases analyzed. The stabilizing effects of the combined EP species β , energy, and density profile in CFETR need further investigation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗