Search NASA⌕ Search

Engineering topics

Gaul, Katherine

Publications and source records attributed to Gaul, Katherine.

In-Situ Thermal Imaging for Single Layer Build Time Alteration in Large-Scale Polymer Additive Manufacturing

Ideally, objects are constructed as quickly as possible; however, short build times for a layer can present an issue. Short layer build times do not provide enough time for the material to cool sufficiently. As a result, an object cannot support its own weight nor deal with overhanging features. Additionally, the generation of support structures may be impractical either due to geometry or, in the case of large-scale polymer additive manufacturing, due to being difficult to remove. To address these issues, researchers at Oak Ridge National Laboratory’s Manufacturing Demonstration Facility investigated the use of a thermal camera mounted to a gantry to collect data on an object under construction. This data provided feedback for an in-situ control system to adjust layer build times. Adjustments were made in the form of additional waiting to allow the material to cool to specific thermal thresholds. This additional cooling time allowed the construction of objects with low layer build times or overhanging features that would have otherwise failed.

Borish, Michael↗

Increasing Interlaminar Strength in Large Scale Additive Manufacturing

Interlaminar strength of extrusion-based additively manufactured parts is known to be weaker than the strength seen in the printed directions (X and Y). With Big Area Additive Manufacturing (BAAM), large parts lead to long layer times that are prone to splitting, sometimes referred to as delamination, between the layers. Fiber filled materials, such as carbon fiber reinforced ABS, are used to counter-act the effects of thermal expansion, but the fibers stay in-plane meaning that no fibers span from layer to layer, which helps counteract the weak interlaminar strength that causes splitting. A solution to this is a patent pending approach known as “z-pinning”. The process involves strategically positioning voids across multiple layers that will be backfilled with hot extrudate. This paper will explore the benefits and results of using “z-pinning” in large scale additive manufacturing.

Roschli, Alex↗

Fieldable Platform for Large-Scale Deposition of Concrete Structures

Oak Ridge National Laboratory’s Manufacturing Demonstration Facility is developing a novel, large-scale additive manufacturing, or 3D printing, system. The Sky Big Area Additive Manufacturing (SkyBAAM) system will ultimately be a fieldable concrete deposition machine with pick and place abilities that will allow for full-scale, automated construction of buildings. The system will be implemented with existing construction equipment meaning conventional cranes will be used to suspend the printhead. SkyBAAM will be cable-driven by four base stations and suspended from a single crane. The elimination of a gantry system, found commonly in large-scale additive manufacturing systems, will enable SkyBAAM to be quickly set up with minimal site preparation. The medium-scale version of SkyBAAM is currently in development. The system design, cable stiffness analysis, and tactics for freezing rotational degrees-of-freedom (DOF), detailed in this paper, will provide a basis for the final, large-scale version of the SkyBAAM system.

Chesser, Phillip↗

Precast Concrete Molds Fabricated with Big Area Additive Manufacturing

The traditional process of making precast concrete molds requires significant manual labor. The molds are made using hardwood, cost tens of thousands of dollars, and take weeks to build. Once built, a mold will last 5-10 pulls before becoming too heavily degraded to continue use. With additive manufacturing, the same mold can be built in eight hours, post-machined in eight hours, costs about $9000, and is project to last nearly 200 pulls. Oak Ridge National Laboratory has been working with Big Area Additive Manufacturing (BAAM) to fabricate concrete molds for a new high-rise apartment complex in New York. The molded pieces will form structural window supports for the hundreds of windows in building façade. The magnitude of window molds is where additive manufacturing can shine when producing the geometry. This paper will discuss the methods and findings of using BAAM to replace conventional precast concrete pattern making.

Roschli, Alex↗

Pick and Place Robotic Actuator for Big Area Additive Manufacturing

Oak Ridge National Laboratory’s Manufacturing Demonstration Facility has created a system that works in tandem with an existing large-scale additive manufacturing (AM) system to ‘pick and place’ custom components into a part as it is printed. Large-scale AM leaves a layered surface finish and is typically post-processed through 5-axis CNC machining. Each surface must be accurately recorded into a laser tracking system. This process can be simplified with the use of fiducials, which are small location indicators placed on the surface of a part. Additionally, the ability to monitor an AM tool via wireless sensors is advantageous to gauge part health as it is fabricated and later used. The ‘pick and place’ system allows thermocouples, fiducials, and other sensors to be accurately placed throughout the tool as it is fabricated. This solution has the potential to reduce time, labor, and cost associated with fabricating, post-processing, and using AM parts.

Boulger, Alex↗

Using Post-tensioning in Large Scale Additive Parts for Load Bearing Structures

One of the perennial problems with additive manufacturing (AM) is the lack of inter-laminar bond strength between the layers, also known as z-strength. This can make the use of AM fabricated parts in load bearing applications problematic. This problem can be solved in some applications with post-tensioning. The use of post-tensioning in structures can be used to ensure that layer interfaces only see compressive stresses. This method is commonly used to strengthen concrete structures since concrete is weak in tension while strong in compression. This paper explores the successful application of post-tensioning to improve z-strength of large structures made with Big Area Additive Manufacturing (BAAM) where loads are significant. Theory and examples are presented herein.

Chesser, Phillip↗

Control System Framework for Using G-Code-Based 3D Printing Paths on a Multi-Degree of Freedom Robotic Arm

This paper describes a control system framework using G-Code-based 3D printing paths on a serial link robot manipulator with multiple degrees of freedom. Usually, G-Code is created by a software application, commonly referred to as a slicer, meant for gantry systems. However, G-Code does not address the kinematic complexity nor take advantage of the flexibility available in serial link robot manipulators. This paper provides an overview of the additive manufacturing process and G-Code, types of additive manufacturing deposition movements, common terminology used, the roles of parsers and translators, step-by-step instructions on how to implement this control system, and results and findings from this research. The presented framework can be used for a number of additive manufacturing methods, hybrid solutions, or applications not directly related to additive manufacturing. The implementation was successfully tested on a manipulator with seven degrees of freedom that successfully performed hundreds of hours of large-scale wire arc metal deposition.

Nycz, Andrzej↗

Effect of Inter-layer Cooling Time on Distortion and Mechanical Properties in Metal Additive Manufacturing (AM)

Laser Metal Deposition with wire (LMD-w) is one of the novel Direct Energy Deposition (DED) processes that is gaining attention in aerospace industry due to the potential cost and lead time reductions for large-scale components. However, improving process parameters (for example, laser power, wire feed rate, robotic travel speed, inter-layer cooling time, etc.) is still under development. These parameters affect thermal gradients that cause residual stresses that in-turn influence distortion. These parameters also affect mechanical properties. Inter-layer cooling time, specifically, is one of the main factors for total production time, and it is used to help mitigate distortion. Therefore, this paper investigated the effects of different inter-layer cooling times on both distortion and mechanical properties. Distortion of deposited Ti-6Al-4V walls was measured automatically using a laser scanner. Finally, suitable recommendations are discussed to optimize the inter-layer cooling time to fabricate components with desired mechanical properties.

Bandari, Yashwanth Kumar↗

Reinforcement Learning for Generating Toolpaths in Additive Manufacturing

Generating toolpaths plays a key role in additive manufacturing processes. In the case of 3-Dimensional (3D) printing, these toolpaths are the pathways the printhead will follow to fabricate a part in a layer-by-layer fashion. Most toolpath generators use nearest neighbor (NN), branch-and-bound, or linear programming algorithms to produce valid toolpaths. These algorithms often produce sub-optimal results or cannot handle large sets of traveling points. In this paper, the researchers at Oak Ridge National Laboratory’s (ORNL) Manufacturing Demonstration Facility (MDF) propose using a machine learning (ML) approach called reinforcement learning (RL) to produce toolpaths for a print. RL is the process of two agents, the player and the critic, learning how to maximize a score based upon the actions of the player in a defined state space. In the context of 3D printing, the player will learn how to find the optimal toolpath that reduces printhead lifts and global print time.

Patrick, Steven↗