Search NASA⌕ Search

Engineering topics

Gee, Ken

Publications and source records attributed to Gee, Ken.

32 records · Page 2
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Computational analysis of forebody tangential slot blowing

An overview of the computational effort to analyze forebody tangential slot blowing is presented. Tangential slot blowing generates side force and yawing moment which may be used to control an aircraft flying at high-angle-of-attack. Two different geometries are used in the analysis: (1) The High Alpha Research Vehicle; and (2) a generic chined forebody. Computations using the isolated F/A-18 forebody are obtained at full-scale wind tunnel test conditions for direct comparison with available experimental data. The effects of over- and under-blowing on force and moment production are analyzed. Time-accurate solutions using the isolated forebody are obtained to study the force onset timelag of tangential slot blowing. Computations using the generic chined forebody are obtained at experimental wind tunnel conditions, and the results compared with available experimental data. This computational analysis compliments the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flow field about simple and complex geometries.

Gee, Ken↗
NASA NTRS1994

Computational Analysis of Forebody Tangential Slot Blowing on the F/A-18

An overview of the computational effort to analyze forebody tangential slot blowing for use on the F/A-18 aircraft is presented. Tangential slot blowing generates side force and yawing moment which may be used to control the aircraft flying at high angle of attack. Computations using the isolated forebody are obtained at full-scale wind tunnel test conditions for direct comparison with available experimental data. The effects of jet exit conditions, jet length, and jet location are also studied using the isolated forebody. In addition, these computations are used to predict the effect of slot blowing at transonic maneuvering flight conditions. The effects of over- and under-blowing on force and moment production are analyzed. Non-time-accurate solutions are obtained to determine the steady-state side force and yawing moments generated by tangential slot blowing. Time-accurate solutions are obtained to study the force onset time lag of tangential slot blowing. The effect of blowing on the burst point location are then analyzed by obtaining computations using the aircraft geometry, which includes the wing, empennage, and faired-over inlets. The effect of blowing on the buffet loads on the vertical tails are analyzed using time-accurate computations. Comparison with available experimental data from full-scale wind tunnel and sub-scale wind tunnel tests are made. This computational analysis compliments the experimental results and provides a detailed understanding of the effects of tangential slot blowing on the flow field about the F/A-18.

Gee, Ken↗
NASA NTRS1993

Effect of forebody tangential slot blowing on flow about a full aircraft geometry

The effect of forebody tangential slot blowing on the flowfield about an F/A-18 aircraft is investigated numerically using solutions of the Navier-Stokes equations. Computed solutions are obtained for a full aircraft geometry, including the fuselage, wing with deflected leading-edge flap, empennage, and a faired-over engine inlet. The computational slot geometry corresponds to that used in full-scale wind tunnel tests. Solutions are computed using flight test conditions and jet mass flow ratios equivalent to wind tunnel test conditions. The effect of slot location is analyzed by computing two non-time-accurate solutions with a 16 in. slot located 3 in. and 11 in. aft of the nose of the aircraft. These computations resolve the trends observed in the full-scale wind tunnel test data. The flow aft of the leading edge extension (LEX) vortex burst is unsteady. A time-accurate solution is obtained to investigate the flow characteristics aft of the vortex burst, including the effect of blowing on tail buffet.

Gee, Ken↗
NASA NTRS1992

Numerical investigation of tail buffet on F-18 aircraft

Numerical investigation of vortex induced tail buffet is conducted on the F-18 aircraft at high angles of attack. The Reynolds-averaged Navier-Stokes equations are integrated using a time-accurate, implicit procedure. A generalized overset zonal grid scheme is used to decompose the computational space around the complete aircraft with faired-over inlet. A weak coupling between the aerodynamics and structures is assumed to compute the structural oscillation of the flexible vertical tail. Time-accurate computations of the turbulent flow around the F-18 aircraft at 30 degrees angle of attack show the surface and off-surface flowfield details, including the unsteadiness created by the vortex burst and its interaction with the vertical twin tail which causes the tail buffet. The effect of installing a LEX fence on modifying the vortex structure upstream of the tail is also examined.

Rizk, Yehia M.↗
NASA NTRS1992

Analysis of a pneumatic forebody flow control concept about a full aircraft geometry

A full aircraft geometry is used to computationally analyze the effectiveness of a pneumatic forebody flow control concept. An overset grid technique is employed to model the aircraft and slot geometry. Steady-state solutions for both isolated forebody and full aircraft configurations are carried out using a thin-layer Navier-Stokes flow solver. A solution obtained using the full aircraft geometry and a flight sideslip condition investigates the effect of sideslip on the leading edge extention vortex burst point. A no-sideslip blowing solution using the isolated forebody at full-scale wind tunnel test conditions is compared with experimental data to determine the accuracy of the numerical method. A solution employing the full geometry and slot blowing at flight conditions is obtained.

Gee, Ken↗
NASA NTRS1991

Accounting For Compressibility In Viscous Flow In Pipes

Method developed to account for effects of compressibility in viscous flows through long, circular pipes of uniform diameter. Based on approximation of variations in density and velocity across pipe cross section by profile equations developed for boundary-layer flow between flat plates.

Steinle, Frank W.↗
NASA NTRS1991

Numerical prediction of the unsteady flowfield around the F-18 aircraft at large incidence

This paper describes a numerical method capable of solving the steady and unsteady viscous flow around complete aircraft configurations at high angles of attack. This method is used to simulate the external flow around the F-18 aircraft, including deflected control surfaces. The current technique employs a generalized overset zonal grid scheme to decompose the computational space around the aircraft. The grid around various components of the aircraft are created numerically using a three-dimensional hyperbolic grid generation procedure. The Reynolds-averaged Navier-Stokes equations are integrated using a time-accurate, implicit procedure. Results for the turbulent flow around the F-18 aircraft at 30 degrees angle of attack show the details of the flowfield structure, including the unsteadiness created by the vortex burst and the resulting fluctuating airloads exerted on the vertical tail. The computed results agree fairly well with flight data for surface pressure, surface flow pattern, vortex burst location, and the dominant frequency for tail load fluctuations.

Rizk, Yehia M.↗
NASA NTRS1991

Computational optimization of a pneumatic forebody flow control concept

The effectiveness of a tangential slot blowing concept for generating lateral control forces on an aircraft forebody is analyzed using computational fluid dynamics. The flow about a fighter forebody is computed using a multiple-zone, thin-layer Navier-Stokes code. Tangential slot blowing is modeled by the use of an actuator plane. The effects of slot location and slot length on the efficiency of the system are analyzed. Results of the study indicate that placement of the slot near the nose of the aircraft greatly enhances the efficiency of the system, while the length and circumferential location of the slot are of secondary importance. Efficiency is defined by the amount of side force or yawing moment obtained per unit blowing coefficient. The effect of sideslip on the system is also analyzed. The system is able to generate incremental changes in forces and moments in flows with sideslip angles up to 10 deg comparable to those obtained at zero sideslip. These results are used to determine a baseline configuration for an experimental study of the tangential slot blowing concept.

Gee, Ken↗
NASA NTRS1990

Numerical simulation of the viscous flow around a simplified F/A-18 at high angles of attack

A numerical method developed for solving the viscous flow around three-dimensional complex configurations is presently used to simulate the flow around a simplified F/A-18 configuration encompassing forebody, wing, leading-edge extension, faired-over inlet, and deflected wing leading-edge flaps, at Mach 0.243 and 30.3 deg angle of attack. The computational results show the details of the flowfield structure, including primary, secondary, and tertiary separation lines, the development of forebody and leading-edge extension vortex, and the burst of this vortex. A grid-refinement study is conducted to assess the effect of grid characteristics on solution accuracy. Substantial agreement is obtained between these results and flight data.

Rizk, Yehia M.↗
NASA NTRS1990

The effect of turbulence models on the numerical prediction of the flowfield about a prolate spheroid at high angle of attack

The F3D thin-layer Navier-Stokes code presently used to numerically investigate the three-dimensional separated flow about a prolate spheroid at high incidence analyzes the effect of different turbulence models on the flowfield solution and the characteristics of the predicted flow. The Johnson-King (1984) model is applied in order to evaluate the importance of modeling nonequilibrium effects in predicting flow about a slender body at high incidence; the computations in question are for steady-state, fully turbulent flow. Insight is gained into the effects of turbulence models on flow characteristics, and model effects on the accurate prediction of highly separated and vortical flows about a slender body are demonstrated.

Gee, Ken↗
NASA NTRS1988

Compressibility effects on flow friction in a fully developed pipe flow

A method was evolved to account for the effects of compressibility in flows through long circular pipes of uniform diameter. Velocity and density variations across the flow cross section were approximated by profile shapes recommended for a flow past flat plates. The wall of the pipe was assumed to have attained an adiabatic condition. An integral method was used to obtain solutions for the governing equations of flow. The method was then used to analyze the detailed pressure measurements made in a long pipe for flow of air at different flow rate settings. Flow friction values derived from these pressure measurements were compared with the standard incompressible pipe flow data available in existing literature.

Murthy, Sreedhara V.↗