CMC COMPONENTS FOR HTR DESIGN AND QUALIFICATION TESTING
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Geringer, Josina.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
The new High Temperature Reactor (HTR) designs being considered for future Gen IV nuclear reactor deployment include designs utilizing molten salt as the primary coolant. These molten-salt cooled, graphite core designs pose new material compatibility challenges that are not considered within the gas-cooled HTR designs that have been previously built and operated. While the Molten Salt Reactor Experiment (MSRE) demonstrated that the molten salt can be considered chemically inert to graphite the novel physical and thermal interactions that the molten salt poses may be just as impactful as the chemical reactivity. Specifically, molten salt intrusion into the open pore structure of nuclear graphite grades can provide additional internal stresses within the microstructure exacerbating the stress buildup from irradiation induced dimensional change. Additionally, designs using a molten salt containing liquid fuel could provide “hot spots” within graphite structural components causing local thermal stresses. Abrasion and erosion concerns are magnified with molten salt due to the extremely high density of the salts (some have higher densities than the structural graphite components). Finally, the graphite-graphite and fuel pebble-graphite tribological behavior are distinctly difference within the molten salt from the inert gas environments and must be investigated. These topics and others are currently under investigation within the DOE Advanced Reactor Technologies (ART) graphite program and will be discussed in depth.
The strength of advanced graphite is reported in accordance with ASTM D7846-16 using a two-parameter Weibull distribution for uniaxial strength testing. The rule of thumb for Weibull distributions is to use a minimum of 30 strength measurements to have a high level of confidence in the Weibull characteristic strength and the Weibull modulus. These large sample sets for statistical confidence are easily obtained for as-manufactured graphite, but determination of the Weibull two-factor parameters on graphite that has been exposed to neutron irradiation is nearly impossible due to irradiation testing restraints on specimen size and space limitations in test reactors for the accommodation of specimens. These restrictions have resulted in irradiation programs that use sub-sized specimens to measure uniaxial strength change, but the specimen geometries still hinder the number of replicate specimens for each irradiation condition. In contrast, this work used an advanced ceramic standard, ASTM C1499-05, as the foundation for equibiaxial strength testing of a superfine-grained nuclear graphite to investigate the irradiation-induced strength change and any changes to the two-parameter Weibull distribution. The goal was to investigate the effect of specimen size on the two-parameter Weibull distribution parameters in support of the small specimens and geometry desired for irradiation. A study of the effect of a reduced sample population was also undertaken to investigate the reliability of using the two-parameter Weibull distribution to study changes to the materials properties caused by neutron irradiation damage. The results of this work suggest that these equibiaxial specimens would be ideal for statistically significant studies of the effects of irradiation on the Weibull characteristic strength (but not the modulus) and for providing a method for surveillance specimen campaigns for future operating commercial reactors.
This work summarizes the current status of the material properties handbook for a structural design using Japanese reduced-activation ferritic/martensitic steel F82H. Specifically, the key structural parameters, e.g. time-independent/dependent design stresses and fatigue design curves, were determined by following the French structural design code RCC-MRx. Moreover, under the Japan–U.S. collaboration, tensile data were newly added to the benchmark heavy irradiation data up to 80 dpa, as critical input information in the intermediate check and review in Japan. Furthermore, the status of structural material data and the near-term and long-term issues were clarified by the evaluation using the attribute guides. In parallel, the structural design approaches, which were newly introduced and extended to cope with the structural design issues under the complex environmental conditions peculiar to the DEMO reactor, were noted with the initial R&D results. Of the many design issues, the multi-axial loading conditions due to the complexity of the DEMO reactor as well as the coolant compatibility and the irradiation effect are mentioned. For example, in the paper, multi-axial fatigue–creep testing and evaluation using the modified universal slope method and brittle/ductile fracture testing and evaluation using the local approach are explained toward DEMO.
Fiber-reinforced ceramic matrix composites have many desirable properties for high-temperature nuclear applications, including excellent thermal and mechanical properties and reasonable to outstanding radiation resistance. Over the last 20 years, the use of ceramic composite materials has already expanded in many commercial nonnuclear industries as fabrication and application technologies mature. The new ASME design and construction rules under Section III, Subsection HH, Subpart B lay out the requirements and criteria for materials, design, machining and installation, inspection, examination, testing, and the marking procedure for ceramic composite core components, which is similar to the established graphite code under Section III, Subsection HH, Subpart A. Moreover, the general requirements listed in Section III, Subsection HA, Subpart B are also expanded to include ceramic composite materials. The code rules rely heavily on the development and publication of standards for composite specification, classification, and testing of mechanical, thermal, and other properties. These test methods are developed in the American Society for Testing and Materials Committee C28 on Advanced Ceramics with a current focus on ceramic composite tubes. Details of the composites code, design methodology, and similarities to the graphite code, as well as guidance for the development of specifications for ceramic composites for nuclear application and recent standard developments, are discussed. The next step is to "close the gap" to support licensing aspects by validating the code with benchmarking data.
Explore the source record for details and available documents.
Liquid Sn is one of the promising coolants for liquid surface divertor concept of fusion reactors. However, the compatibility between liquid Sn and structural materials is an important issue that has to be addressed, because liquid Sn is extremely corrosive to steels at high temperatures. The corrosion may be mitigated when a protective Al2O 3 layer is formed on the surface of alumina forming steels. However, the effect of neutron irradiation on the integrity of protective layer is not made clear so far. Japan and US joint research project “FRONTIER” started in 2019 to investigate the material compatibility under neutron irradiation. The purpose of the present study is to develop the conceptual design of the irradiation test capsule which enables material compatibility tests for the alumina forming steels - liquid metal systems under neutron irradiation in the High Flux Isotope Reactor at Oak Ridge National Laboratory, TN, USA. The three dimensional drawing of capsule structure was then developed. The validity of the material selections for the capsule design was investigated by means of corrosion tests of SiC, Si3N4, Ti, and Mo in liquid Sn at 773 K for 262 hr.
In this study, we performed fracture toughness characterization of ten neutron-irradiated Eurofer97 variants using precracked miniature multi-notch bend bar (M4CVN) specimens based on the Master Curve method in the ASTM E1921 standard. The neutron irradiation was performed in the flux trap position of the High Flux Isotope Reactor (HFIR) of the Oak Ridge National Laboratory (ORNL) with the nominal irradiation temperature of 300°C and irradiation dose of 2.5 displacements per atom (dpa). Depending on the irradiation temperature and materials, we observed different degrees of irradiation hardening and embrittlement for ten Eurofer97 variants. The upper shift in the Master Curve reference temperature T0Q vs. the increase in Vickers microhardness values showed a liner relationship for only a few materials indicating different irradiation responses of the Eurofer97 variants.
The irradiation temperature of silicon carbide (SiC) was determined post-irradiation by examination of the recovery of the electrical resistivity due to thermal annealing in a rapid heating/cooling optical furnace. High-purity, high-resistivity grade SiC is routinely used as a passive temperature monitor in neutron irradiation studies at the High Flux Isotope Reactor (HFIR), and this paper presents an alternative automated technique for determination of the irradiation temperature the SiC experienced. Neutron collisions with the atoms results in displaced lattice atoms (interstitials) that act as electron donors yielding a significant decrease in electrical resistivity. The irradiation defects become thermodynamically unstable and start to recombine, when annealed above the irradiation temperature, resulting in a recovery of the electrical resistivity. The resistivity is measured at a fixed elevated temperature above ambient, which is below the target irradiation temperature. When the resistivity is plotted as a function of annealing temperatures, a clear increase is observed due to the recovery of irradiation defects. We have demonstrated that this electrical resistivity measurement of SiC is effective to determine irradiation temperature of SiC. In conclusion, energy levels of various defects in SiC were calculated from Arrhenius plots of electrical conductivity versus inverse temperature.
Neutron irradiation effects on the tensile properties of Pure W, K-doped W, W–3%Re, and K-doped W–3%Re were examined under the US-Japan collaboration project PHENIX. The fission neutron irradiation experiments were carried out up to 0.74 dpa at 600 °C and 800 °C. Pure W (SR) showed irradiation hardening and loss of ductility after irradiation at 600 °C and 800 °C. K-doped W–3%Re (SR) also exhibited irradiation hardening but was ductile after irradiation. Characteristic points of the K-doped W–3%Re (SR) are small grain size and layered structure. Finally, the stress-relief treatment and the layered structure may improve the ductility of powder-metallurgy W alloys after neutron irradiation, so a combination of K-doping and Re addition would be beneficial to improve irradiation resistance.
A program underway at Oak Ridge National Laboratory (ORNL) to support private industry design of a system for production of 99Mo includes review of Zircaloy-4 (Zry-4) properties as a potential material for a primary vessel in the system. Because Zry-4 is not a material specified in the ASME Boiler and Pressure Vessel Code, a review has been performed to obtain the necessary data in the non-irradiated condition from the literature and from additional testing of Zry-4 to enable creation of tables of material properties required for ASME Code Section III Article ND-3000 design. A strategy for an in-vessel surveillance program is also recommended for early detection of potential corrosion and irradiation degradation issues during operational life of the vessel. Additionally, the ASME Code Section II, Part D was reviewed to ascertain the requirements for proposing a new material for Code approval. A plate of Zry-4 procured by ORNL was used to obtain tensile properties that were used as the basis for determining the maximum allowable stresses applicable to the vessel design. The materials properties of primary interest for ASME Code application are tensile properties, fracture toughness, fatigue, and five specific physical properties required by the Code for approval of a new material. The literature review revealed that all reported experimental data showed tensile strengths to substantially exceed the minimum specifications in ASTM B352. Sufficient fracture toughness and fatigue data are available to conclude that Zry-4 has sufficient fracture and fatigue resistance in the unirradiated condition for vessel design and operation. Of the physical properties reviewed, only thermal conductivity revealed a discrepancy that is recommended for further review. A surveillance program plan has been developed that is probably the maximum that would need to be implemented for the specific vessel design considered. Once adequate non-irradiated and irradiated data are available from preproduction testing of the Zry-4 and weld metal and HAZ materials, the program could be reduced to reflect that either initial properties are very good and/or the effects of embrittlement appear to be minimal. However, the overall design of a surveillance program is, of course, also dependent on the ASME Code design class for the pressure vessel.
Explore the source record for details and available documents.
The PHENIX Project is a 6-year U.S./Japan bilateral, multi-institutional collaboration program for the Technological Assessment of Plasma Facing Components for DEMO Reactors. The goal is to address the technical feasibility of helium-cooled divertor concepts using tungsten as the armor material in fusion power reactors. The project specifically attempts to (1) improve heat transfer modeling for helium-cooled divertor systems through experiments including steady-state and pulsed high-heat-load testing, (2) understand the thermomechanical properties of tungsten metals and alloys under divertor-relevant neutron irradiation conditions, and (3) determine the behavior of tritium in tungsten materials through high-flux plasma exposure experiments. The High Flux Isotope Reactor and the Plasma Arc Lamp facility at Oak Ridge National Laboratory, the Tritium Plasma Experiment facility at Idaho National Laboratory, and the helium loop at Georgia Institute of Technology are utilized for evaluation of the response to high heat loads and tritium interactions of irradiated and unirradiated materials and components. This paper provides an overview of the progress achieved during the first 3 years and discusses the plan for the remainder of the project.
Zr-based alloys, namely Zircaloy-2, Zircaloy-4, ZIRLO, or M5, have been used in light water reactors (LWRs) as structural materials (cladding, pressure tubes, and etc.). Under irradiation conditions, especially at harsh pressurized water reactor (PWR) conditions, these Zr alloys can undergo embrittlement due to corrosion, hydriding, and irradiation induced stresses. This ultimately leads to the severe degradation of Zr-alloys and increase the probability of fuel failure. While various research efforts have been conducted in developing better Zr-based alloys to withstand these harsh environments, there is a considerable amount of Zr-alloy characteristics, such as change in mechanical properties under irradiation conditions and its relationship to the materials microstructure, that need to be studied. This present study has focused on investigation of mechanical and microstructural properties of Zircaloy-4 under low temperature (80 - 100 deg. C) neutron irradiation conditions. Some of the samples studied were also hydrided to evaluate influence of hydride precipitates in the material. (authors)