Engineering topics

Geringer, Josina W.

Publications and source records attributed to Geringer, Josina W..

5 records

DOE OSTI2024

Microstructure, electrical resistivity, and tensile properties of neutron-irradiated Cu–Cr–Nb–Zr

High strength, high conductivity copper alloys that can resist creep at high temperatures are one of the primary candidates for efficient heat exchangers in fusion reactors. Cu–Cr–Nb–Zr (CCNZ) alloys, which were designed to improve the strength and creep life of ITER Cu–Cr–Zr (CCZ) reference alloys, have been found to have comparable electrical conductivity and tensile properties to CCZ alloys. The measured creep rupture times for these improved alloys is about ten times higher than the ITER reference alloys at 90–125 MPa at 500 °C. However, the effects of neutron irradiation on these alloys, and the ensuing material properties, have not been studied; thus, their utility in a fusion reactor environment is not well understood. This study characterizes the room temperature mechanical and electrical properties of a neutron-irradiated CCNZ alloy and compares them to a neutron-irradiated ITER reference heat sink CCZ alloy. Tensile specimens were neutron irradiated in the High Flux Isotope Reactor (HFIR) to 5 dpa between 250 °C and 325 °C. Post-irradiation characterization included electrical resistivity measurements, hardness, and tensile tests. Microstructural evaluation used scanning electron microscopy, energy dispersive x-ray spectroscopy, and atom probe tomography to characterize the irradiation-produced changes in the microstructure and investigate the mechanistic processes leading to post-irradiation properties. Transmutation calculations were validated with composition measurements from atom probe data and used to calculate contributions to the increased electrical resistivity measured after irradiation. Comparisons with CCZ alloys in the same irradiation heat found that the post-irradiated CCNZ and CCZ alloys had comparable electrical resistivity. Although CCNZ alloys suffered more irradiation hardening than CCZ, the overall tensile behavior deviated very little from non-irradiated values in the temperature range studied.

36 MATERIALS SCIENCE↗

DOE OSTI2024

Analysis of the ASME Code Rules for Subsection III-5-HHB (Composite Materials) for Current HTR Design Requirements

This document includes the critical analysis review of the American Society of Mechanical Engineers (ASME) Section III Division 5 Subsection HH Subpart B (HHB), including Mandatory Appendices, that was published in 2023. In the context of this document, reference to “the code” is specific to this subsection unless otherwise specified. A specific composites task group within the ASME Nonmetallic Design and Materials Working Group, with the support of external experts, was established to perform a gap analysis review. The significant findings are summarized here. The committee response with suggested action items are detailed in the body of the report.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Review of Recent Progress in Plasma-Facing Material Joints and Composites in the FRONTIER U.S.-Japan Collaboration

The plasma-facing components (PFCs) of future fusion reactors will have intricate structures and require multiple materials because no one material can simultaneously satisfy all the requirements of the component. The dissimilar material joints in PFCs must withstand extreme thermal and stress gradients under neutron irradiation. The Fusion Research Oriented to Neutron Irradiation and Tritium Behavior at Material Interfaces (FRONTIER) U.S.-Japan collaboration seeks to explore and explain the behavior of internal solid interfaces in PFCs under neutron irradiation. The first step of the collaboration was to identify the leading PFCs that should be studied further and prepare them for the next step, which will include neutron irradiation. Different strategies for material development are being pursued worldwide to produce robust PFCs. Here, in this work, an overview is presented of some of the most promising materials in the areas of copper alloys, tungsten-copper composites, tungsten-steel composites, additively manufactured tungsten, particle-reinforced tungsten, and tungsten and SiC fiber composites. Each material’s fabrication and benefits are described, and some discussion of remaining questions is given.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Codes and standards for ceramic composite core materials for High Temperature Reactor applications

Fiber-reinforced ceramic matrix composites are attractive for high-temperature nuclear applications due to excellent thermal and mechanical properties as well as reasonable-to-outstanding radiation resistance. Over the past 20 years, the use of ceramic matrix composite applications expanded to many commercial non-nuclear industries as fabrication and application of the technologies mature. The ASME Boiler Pressure Vessel Code, under Section III Division 5, provides the design and construction rules for High Temperature Reactor components. It published the first rules for ceramic matrix composites to be used for reactor core components. The rules lay out the quality requirements together with the design and materials criteria for the use and application of silicon carbide- and carbon-based matrix material technologies. As with the established graphite rules, the ceramic composite material rules are structured in Subsection HH (from Section III), that addresses the criteria for class SN nonmetallic core components. The code rules rely heavily on the development and publication of standards for composite specification, classification, and testing of mechanical, thermal, and other properties. These test methods are developed in ASTM Committee C28 on Advanced Ceramics, with a current focus on ceramic composite tubes. This article describes the detail of the composites code, the design methodology and similarities to the graphite code, the guidance for the development of specifications for ceramic composites (for nuclear applications) including recent standard developments, and it mentions the next steps to support licensing aspects by validating the code with benchmarking data.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Preparation & shipping of ten neutron irradiated Eurofer97 steel variants to HFIR for SANS experiments

At ORNL, ten variants of Eurofer97 steel were irradiated in the high flux isotope reactor (HFIR) to ~2.94 – 3.24 dpa at 300 ± 30 °C, as part of the EUROfusion Lot-IV collaboration. The irradiations were performed in non-instrumented rabbit capsules in the flux trap region, which included SS-J3 type tensile samples and M4-CVN multi-notch bend bars. Their full set of microstructure and mechanical properties were previously reported in multiple previous publications. In this project, half-broken irradiated and nonirradiated SS-J3 tensile samples from ten alloys, code-named H, I, J, K, L, M, N, O, P and E, were prepared and shipped for facilitating small angle neutron scattering (SANS) experiments at the HFIR general purpose (GP)-SANS beam line. This report summarizes the completed tasks which included canister moves at the Irradiated Materials Examination and Testing (IMET) hot-cell facility to retrieve the samples from long-term storage, loading of the ten irradiated samples at IMET inside lead (Pb) piglets that were specifically provided by ORNL for SANS experiments and radiological shipment from IMET facility to the HFIR hot cells for performing SANS experiments. In addition to the irradiated samples, ten nonirradiated half-broken pieces from the Eurofer97 variants were also provided to HFIR for SANS.

36 MATERIALS SCIENCE↗