Engineering topics

Ghosh, Dave

Publications and source records attributed to Ghosh, Dave.

13 records

NASA NTRS1994

Simulation of the coupled multi-spacecraft control testbed at the Marshall Space Flight Center

The capture and berthing of a controlled spacecraft using a robotic manipulator is an important technology for future space missions and is presently being considered as a backup option for direct docking of the Space Shuttle to the Space Station during assembly missions. The dynamics and control of spacecraft configurations that are manipulator-coupled with each spacecraft having independent attitude control systems is not well understood and NASA is actively involved in both analytic research on this three dimensional control problem for manipulator coupled active spacecraft and experimental research using a two dimensional ground based facility at the Marshall Space Flight Center (MSFC). This paper first describes the MSFC testbed and then describes a two link arm simulator that has been developed to facilitate control theory development and test planning. The motion of the arms and the payload is controlled by motors located at the shoulder, elbow, and wrist.

Ghosh, Dave↗

NASA NTRS1994

Control of flexible structures with distributed sensing and processing

Technology is being developed to process signals from distributed sensors using distributed computations. These distributed sensors provide a new feedback capability for vibration control that has not been exploited. Additionally, the sensors proposed are of an optical and distributed nature and could be employed with known techniques of distributed optical computation (Fourier optics, etc.) to accomplish the control system functions of filtering and regulation in a distributed computer. This paper extends the traditional digital, optimal estimation and control theory to include distributed sensing and processing for this application. The design model assumes a finite number of modes which make it amenable to empirical determination of the design model via familiar modal-test techniques. The sensors are assumed to be distributed, but a finite number of point actuators are used. The design process is illustrated by application to a Euler beam. A simulation of the beam is used to design an optimal vibration control system that uses a distributed deflection sensor and nine linear force actuators. Simulations are also used to study the influence of design and processing errors on the performance.

Ghosh, Dave↗

NASA NTRS1994

Testing of an End-Point Control Unit Designed to Enable Precision Control of Manipulator-Coupled Spacecraft

This paper presents an end-point control concept designed to enable precision telerobotic control of manipulator-coupled spacecraft. The concept employs a hardware unit (end-point control unit EPCU) that is positioned between the end-effector of the Space Shuttle Remote Manipulator System and the payload. Features of the unit are active compliance (control of the displacement between the end-effector and the payload), to allow precision control of payload motions, and inertial load relief, to prevent the transmission of loads between the end-effector and the payload. This paper presents the concept and studies the active compliance feature using a simulation and hardware. Results of the simulation show the effectiveness of the EPCU in smoothing the motion of the payload. Results are presented from initial, limited tests of a laboratory hardware unit on a robotic arm testbed at the l Space Flight Center. Tracking performance of the arm in a constant speed automated retraction and extension maneuver of a heavy payload with and without the unit active is compared for the design speed and higher speeds. Simultaneous load reduction and tracking performance are demonstrated using the EPCU.

Montgomery, Raymond C.↗

NASA NTRS1993

Evaluation of inertial devices for the control of large, flexible, space-based telerobotic arms

Inertial devices, including sensors and actuators, offer the potential of improving the tracking of telerobotic commands for space-based robots by smoothing payload motions and suppressing vibrations. In this paper, inertial actuators (specifically, torque-wheels and reaction-masses) are studied for that potential application. Batch simulation studies are presented which show that torque-wheels can reduce the overshoot in abrupt stop commands by 82 percent for a two-link arm. For man-in-the-loop evaluation, a real-time simulator has been developed which samples a hand-controller, solves the nonlinear equations of motion, and graphically displays the resulting motion on a computer workstation. Currently, two manipulator models, a two-link, rigid arm and a single-link, flexible arm, have been studied. Results are presented which show that, for a single-link arm, a reaction-mass/torque-wheel combination at the payload end can yield a settling time of 3 s for disturbances in the first flexible mode as opposed to 10 s using only a hub motor. A hardware apparatus, which consists of a single-link, highly flexible arm with a hub motor and a torque-wheel, has been assembled to evaluate the concept and is described herein.

Montgomery, Raymond C.↗

NASA NTRS1993

A testbed for research on manipulator-coupled active spacecraft

This paper describes a testbed developed to study control of manipulator-coupled spacecraft with active attitude control systems. Pre-design simulation studies are described that were used to size and design the experimental facility and plan testing programs. Results on the dynamics and control of this testbed are presented that were obtained from both simulations and experiments. Initial experimental results have been used to refine the simulators using output matching system identification. Results from this system identification are included in the form of comparisons between simulation and experiment time histories for various model parameter values. These show that the testbed is inherently nonlinear and that parameters, harmonic gear effectiveness, in particular, have appreciable effects on the dynamics.

Montgomery, Raymond C.↗

NASA NTRS1992

Ongoing Progress in Spacecraft Controls

This publication is a collection of papers presented at the Mars Mission Research Center workshop on Ongoing Progress in Spacecraft Controls. The technical program addressed additional Mars mission control problems that currently exist in robotic missions in addition to human missions. Topics include control systems design in the presence of large time delays, fuel-optimal propulsive control, and adaptive control to handle a variety of unknown conditions.

Ghosh, Dave↗

NASA NTRS1992

Evaluation of inertial devices for the control of large, flexible, space-based telerobotic arms

Batch simulation studies which show that torque-wheels can reduce the overshoot in abrupt stop commands by 82 percent for a two-link arm are presented. For man-in-the-loop evaluation, a real-time simulator has been developed that samples a hand-controller, solves the nonlinear equations of motion, and graphically displays the resulting motion on a computer workstation. It is shown that, for a single-link arm, a reaction-mass/torque-wheel combination at the payload end can yield a settling time of 3 s for disturbances in the first flexible mode as opposed to 10 s utilizing only a hub motor.

Montgomery, Raymond C.↗

NASA NTRS1991

Analytic and simulation studies on the use of torque-wheel actuators for the control of flexible robotic arms

This paper presents results of analytic and simulation studies to determine the effectiveness of torque-wheel actuators in suppressing the vibrations of two-link telerobotic arms with attached payloads. The simulations use a planar generic model of a two-link arm with a torque wheel at the free end. Parameters of the arm model are selected to be representative of a large space-based robotic arm of the same class as the Space Shuttle Remote Manipulator, whereas parameters of the torque wheel are selected to be similar to those of the Mini-Mast facility at the Langley Research Center. Results show that this class of torque-wheel can produce an oscillation of 2.5 cm peak-to-peak in the end point of the arm and that the wheel produces significantly less overshoot when the arm is issued an abrupt stop command from the telerobotic input station.

Montgomery, Raymond C.↗

NASA NTRS1991

Simulator evaluation of system identification with on-line control law update for the controls and astrophysics experiment in space

A procedure for optimizing the performance of large flexible spacecraft that require active vibration suppression to achieve required performance is presented. The procedure is to conduct on-orbit testing and system identification followed by a control system design. It is applied via simulation to a spacecraft configuration currently being considered for flight test by NASA - the Controls, Astrophysics, and Structures Experiment in Space (CASES). The system simulator is based on a NASTRAN finite element structural model. A finite number of modes is used to represent the structural dynamics. The system simulator also includes models of the electronics, actuators, sensors, the digital controller, and the internal and external disturbances. Nonlinearities caused by quantization are included in the study to examine tolerance of the procedure to modelling errors. Disturbance and sensor noise is modelled as a Gaussian process. For system identification, the system is excited using sinusoidal inputs at the resonant frequencies of the structure using each actuator. Mode shapes, frequencies, and damping ratios are identified from the unforced response sensor data after each excitation. Then, the excitation data is used to identify the actuator influence coefficients. The results of the individual parameter identification analyses are assembled into an aggregate system model. The control design is accomplished based only on the identified model using multi-input/output linear quadratic Gaussian theory. Its performance is evaluated based on time-to-damp as compared with the uncontrolled structure.

Montgomery, Raymond C.↗

NASA NTRS1991

Control with distributed sensing and processing

A design procedure for control systems that use distributed sensing and processing is summarized. The procedure is applied to the problem of damping vibrations of a simply supported beam.

Montgomery, Raymond C.↗

NASA NTRS1991

Studies on distributed sensing and processing for the control of large flexible spacecraft

Technology is being developed to process signals from distributed sensors using distributed computations. These distributed sensors provide a new feedback capability for vibration control that has not been exploited. Additionally, the sensors proposed are of an optical and distributed nature and could be employed with known techniques of distributed optical computation (Fourier optics, etc.) to accomplish the control system functions of filtering and regulation in a distributed computer. This paper reviews a procedure for the analytic design of control systems for this application. For illustration, the procedure is applied to the problem of suppressing the vibrations of a simply supported beam. A simulator has been developed to study the effects of sensor and processing errors. An extensive study of the effects of these errors on estimation and regulation performance is presented.

Montgomery, Raymond C.↗

NASA NTRS1990

Active control test on the Mini-Mast

A Linear Quadratic Gaussian (LQG) design process is presented and applied to a large flexible ground test facility, the Mini-Mast, for validation. For the design, nine displacement sensors were used. Three torque wheel actuators were used for damping augmentation. Results were dramatic, indicating an improvement in damping from 3 percent to 30 percent of critical. The tests proved the effectiveness of the procedure in designing effective vibration damping systems.

Montgomery, Raymond C.↗

NASA NTRS1990

On the use of distributed sensing in control of large flexible spacecraft

Distributed processing technology is being developed to process signals from distributed sensors using distributed computations. Thiw work presents a scheme for calculating the operators required to emulate a conventional Kalman filter and regulator using such a computer. The scheme makes use of conventional Kalman theory as applied to the control of large flexible structures. The required computation of the distributed operators given the conventional Kalman filter and regulator is explained. A straightforward application of this scheme may lead to nonsmooth operators whose convergence is not apparent. This is illustrated by application to the Mini-Mast, a large flexible truss at the Langley Research Center used for research in structural dynamics and control. Techniques for developing smooth operators are presented. These involve spatial filtering as well as adjusting the design constants in the Kalman theory. Results are presented that illustrate the degree of smoothness achieved.

Montgomery, Raymond C.↗