Search NASA⌕ Search

Engineering topics

Ghosh, Somnath

Publications and source records attributed to Ghosh, Somnath.

4 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Comparison of three state-of-the-art crystal plasticity based deformation twinning models for magnesium alloys

In magnesium alloys, deformation twinning and its interactions with dislocation slip are responsible for a sigmoidal shape stress–strain behavior and an asymmetrical tension–compression yield strength in magnesium alloys. The sensitivity of twinning to the underlying microstructure renders the crystal plasticity method the most commonly adopted modeling approach for magnesium-twinning. This paper compares three state-of-the-art crystal plasticity-based twinning models from the literature, namely the elastic-viscoplastic self-consistent twinning-detwinning (EVPSC-TDT) model, crystal plasticity finite element model based on enhanced predominate twin reorientation approach (CPFE-ePTR), and the crystal plasticity finite element model based on “discrete twinning” approach (CPFE-DT). A polycrystalline microstructure is simulated with all three methods to compare the resulting stress–strain curves and lattice strains to those from the experimentally measured data. All three methods showed the capability of capturing the experimental results with different levels of accuracy. Additionally, the EVPSC-TDT method avoids solving the finite element matrices and showed the highest computational efficiency. The CPFE-ePTR model shows a higher accuracy in capturing the lattice strain. The CPFE-DT relies on high-resolution finite element mesh and is much slower than the other two methods, but it captured the local deformation concentration and stress reversal phenomena near the twin band, which was not possible with the other two methods. Based on the comparison, guidance for the selection of the appropriate model based on the specific modeling target is provided in this paper.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Micro-mechanical investigation of the thermo-mechanical properties of micro-architectured tungsten coatings

The thermo-mechanical response of micro-architectured tungsten coatings is characterized in the temperature range of 293 to 673 K using both in situ micro-compression experiments inside a scanning electron microscope (SEM) as well as image-based crystal plasticity finite element method (CPFEM) simulations. The experiments were conducted on micropillar-like specimens that were focus ion beam milled into the coatings, while the simulations were conducted on columnar-grained micropillar simulation cells constructed based on the statistics of the coating’s microstructure. The experimental results show that the stress–strain response and deformation mode exhibit a strong temperature-dependence. At room temperature, catastrophic failure is observed shortly after yield and is manifested in the form of intergranular fracture and buckling of individual columnar grains. With increasing temperature, this catastrophic failure is gradually suppressed and the material exhibits a steadier strain hardening response at 693 K. The CPFEM simulations are also shown to be in good agreement with the experimental results, and these simulations indicate that the material response is strongly influenced by the local crystallographic anisotropy and microstructure inhomogeneity. Furthermore, the simulations capture the underlying mechanisms that control the temperature-dependent transition in deformation mode. The current results highlight that the micro-architectured microstructure offers a great combination of excellent mechanical strength and structural integrity at elevated temperatures, which is of importance for high temperature applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

A finite element formulation for deformation twinning induced strain localization in polycrystal magnesium alloys

Deformation twinning induces shear strain localization in hexagonal close-packed crystals and is critical for the material’s ductility and failure. Cracks often occur at twin-twin or twin-grain boundary intersections and propagate along twin bands. However, most crystal plasticity models for deformation twinning are based on a “pseudo-slip” approach and do not capture the localized deformation associated with the formation of each discrete twin band. The few exceptions are discrete twin models that involve very complex numerical algorithms and are often compromised in accuracy due to the numerical convergence. These factors make the discrete twin models hard to adopt. This paper proposes a modification to the conventional finite element weak form, to fully incorporate a twin-induced heterogeneous deformation that does not depend on the “pseudo-slip” assumption. The model starts by splitting the deformation gradient into elastic-slip-twinning components. The twin-induced deformation gradient component is computed separately by solving a microstructural evolution problem and then implemented into finite element weak form by constructing a global “twin-force” vector. The constitutive update (e.g., in the user-defined material subroutine, or UMAT, for ABAQUS) therefore avoids dealing with the twinning and recovers to the form of a regular slip-based crystal plasticity model. The results presented here indicate that the twin-induced strain localization and the associated stress-reversal phenomena near the twin band were naturally captured in the model, which was validated against an in-situ synchrotron X-ray micro-diffraction experiment.

36 MATERIALS SCIENCE↗