Search NASA⌕ Search

Engineering topics

Gilson, E. P.

Publications and source records attributed to Gilson, E. P..

9 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Initial design concepts for solid boron injection in ITER

As part of ITER’s consideration to change its first wall material from beryllium to tungsten, the ITER Organization has proposed studying the feasibility of real-time solid boron injection (SBI) into the plasma to coat the walls and divertor to supplement glow discharge boronization (GDB). Boron deposits getter oxygen and reduce sputtering of tungsten from plasma facing components (PFCs). Particularly in areas with significant plasma wall interactions, boron coatings are expected to be short-lived under high performance plasma conditions. The proposed SBI system aims to maintain boron layers in these areas to avoid excessive radiation from tungsten in the plasma as a risk mitigation to ensure ITER will be able to reach and sustain Q = 10 conditions. The system will be used sparingly, as redeposition of boron can lead to significant tritium retention, which must be minimized in ITER to comply with nuclear safety concerns. SBI is proposed to limit and precisely control the amount of boron injected in real-time during plasma operation. Here, some of the design requirements and initial concepts for an SBI system in ITER are presented based on previous results carried out with SBI systems on a number of tokamaks and stellarators around the world. Previous results using SBI systems installed by PPPL have injected boron particles from 5 µm–2 mm diameter at calibrated rates of 2–200 mg/s in real-time during plasma operation on AUG, DIII-D, EAST, KSTAR, LHD, TFTR, WEST, and W7-X, leading to improved wall conditions with reduced plasma impurity concentrations and radiated power and improved plasma performance. The boron is ionized in the plasma edge and then deposited on plasma-wetted surfaces. On AUG, EAST and WEST reduced tungsten sputtering sources were observed following several discharges with SBI. Extrapolation of these SBI results are presented to estimate the amount of boron needed for wall conditioning in ITER. Real-time SBI control requirements and plasma operation scenarios for ITER are also described.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Full-torus impurity transport simulation in boron powder injection experiments in the Large Helical Device

The toroidal distribution of boron deposition on plasma-facing components (PFCs) in boron powder injection using an impurity power dropper (IPD) was investigated by full-torus simulation and observations in a systematic plasma density-scan experiment. The images of the ablation of dropped boron powders observed with a visible CCD camera were consistently explained by the simulations of the ablation positions of the boron powders considering the size distribution. Simulations assuming full-torus boron deposition on the PFCs did not reproduce the observed intensity profile of boron emission lines for higher plasma densities. It indicated that the density of boron deposited on PFCs installed toroidally far from the IPD was low for higher plasma densities due to the change in the ablation positions of the boron powders toward the outboard side. The experimental results verified the previous full-torus simulation of the toroidal distribution of the boron deposition in both lower and higher plasma densities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Experimental study on boron distribution and transport at plasma-facing components during impurity powder dropping in the Large Helical Device

Toward real-time wall conditioning, impurity powder dropping experiments with boron powder were performed in the 22nd experimental campaign of the Large Helical Device. To examine the deposition and desorption process of boron, we focus on boron hydride (BH) molecules which presumably populate near plasma-facing components. We performed spatially-resolved spectroscopic measurements of emission by boron ions and BH molecules. From the measurement, we found that BH and B + were concentrated on the divertor viewing chord, which suggest boron deposition in the divertor region. By comparing Hγ emissions with and without boron injection, neutral hydrogen shows uniform reduction in the SOL region, whereas less reduction of neutral hydrogen is confirmed in the divertor region. Although emissions from BH and B + increased linearly, emissions by B0 and B4 + became constant after the middle of the discharge. Continuous reduction of carbon density in the core plasma was confirmed even after B 0 and B 4 + became constant. The results may show reduction of hydrogen recycling and facilitation of impurity gettering by boron in the divertor region and thus effective real-time wall conditioning.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Generation of mean flows in rotating anisotropic turbulence: The case of solar near-surface shear layer

Results from helioseismology indicate that the radial gradient of the rotation rate in the near-surface shear layer (NSSL) of the Sun is independent of latitude and radius. Theoretical models using the mean-field approach have been successful in explaining this property of the NSSL, while global direct or large-eddy magnetoconvection models have so far been unable to reproduce this. We investigate the reason for this discrepancy by measuring the mean flows, Reynolds stress, and turbulent transport coefficients under conditions mimicking those in the solar NSSL. Simulations with as few ingredients as possible to generate mean flows were studied. These ingredients are inhomogeneity due to boundaries, anisotropic turbulence, and rotation. The parameters of the simulations were chosen such that they matched the weakly rotationally constrained NSSL. The simulations probe locally Cartesian patches of the star at a given depth and latitude. The depth of the patch was varied by changing the rotation rate such that the resulting Coriolis numbers covered the same range as in the NSSL. We measured the turbulent transport coefficient relevant for the nondiffusive (Λ-effect) and diffusive (turbulent viscosity) parts of the Reynolds stress and compared them with predictions of current mean-field theories. A negative radial gradient of the mean flow is generated only at the equator where meridional flows are absent. At other latitudes, the meridional flow is comparable to the mean flow corresponding to differential rotation. We also find that the meridional components of the Reynolds stress cannot be ignored. Additionally, we find that the turbulent viscosity is quenched by rotation by about 50% from the surface to the bottom of the NSSL. Our local simulations do not validate the explanation for the generation of the NSSL from mean-field theory where meridional flows and stresses are neglected. However, the rotational dependence of the turbulent viscosity in our simulations agrees well with theoretical predictions. Moreover, our results agree qualitatively with global convection simulations in that an NSSL can only be obtained near the equator.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

Wall conditioning and ELM mitigation with boron nitride powder injection in KSTAR

Results from KSTAR powder injection experiments, in which tens of milligrams of boron nitride (BN) were dropped into low-power H-mode plasmas, show an improvement in wall conditions in subsequent discharges and, in some cases, a reduction or elimination of edge-localized modes (ELMs). Injected powder is distributed by the plasma flow and is deposited on the wall and, over the course of several discharges, was observed to gradually reduce recycling by 33%, and decrease both the ELM amplitude and frequency. This is the first demonstration of the use of BN for ELM mitigation. In all of these experiments, an Impurity Powder Dropper (IPD) was used to introduce precise, controllable amounts of the materials into ELMy H-mode KSTAR discharges. The plasma duration was between 10 s and 15 s, I p = 500 kA, B T = 1 . 8 T, P NBI = 1 . 6 MW, and P ECH = 0 . 6 MW. Plasma densities were between 2 and 3 × 1 0 19 m -3 . In all cases, the pre-fill and startup gas-fueling was kept constant, suggesting that the decrease in baseline D α emission is in fact due to a reduction in recycling. The results presented herein highlight the viability of powder injection for intra-shot and between-shot wall conditioning

36 MATERIALS SCIENCE↗
DOE OSTI2020

ELM Suppression by Boron Powder Injection and Comparison with Lithium Powder Injection on EAST

Type I edge-localized modes (ELMs) in the Experimental Advanced Superconducting Tokamak (EAST) were completely suppressed via boron powder injection into the X-point region of an upper-single null configuration over a wide range of operating conditions (2.8 < P aux < 7.5 MW, 3.8 × 10 19 < n e < 6 × 10 19 m -3 , RF-only and RF + NBI heating scenarios, both grad-B drift directions, and even He ion majority plasmas) (Sun et al. in Nucl. Fusion, 2020). A window of edge B concentration for stable long pulse operation was identified: too low and ELMs return, too high and the discharge suffers radiative collapse. The injection of boron powder above the minimum for ELM suppression coincided with the occurrence of an edge harmonic oscillation detected in magnetics (both on the high-field side and low-field side), in AXUV diodes near the upper X-point, divertor Dα emission, and in a range of other diagnostics (Diallo et al. in: Proceedings of 2020 IAEA fusion energy conference, 2021). Furthermore, no harmonic oscillation was observed when ELMs were present, and stored energy was slightly increased at constant density during ELM suppression. Core tungsten emission during ELM suppression either increased or decreased relative to ELMy H-mode, but the W emission was maintained at acceptable levels. The threshold B injection rate was measured for several conditions, and found to increase with heating power. Li powder injection into comparable discharges also resulted in a short phase of ELM suppression, but density and stored energy both decreased due to the strong pumping effect of lithium; no edge harmonic oscillation was observed with Li injection, indicating that the ELM suppression mechanisms differ. The new set of B-seeded, ELM-suppressed discharges exhibited certain characteristics of quiescent H-mode (Burrell et al. in Phys Plasmas 8:2153, 2001), but did not require high shear, counter beams, etc. The wide operating window and compatibility with RF-only discharges paves the way for future experiments targeting long pulse H-mode discharges with complete ELM suppression.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Observations of wall conditioning by means of boron powder injection in DIII-D H-mode plasmas

In this paper, we report observations from the DIII-D tokamak indicating that boron (B) powder injection in tokamak plasmas improves wall conditions similarly to glow discharge boronization (GDB). Isotopically enriched B powder (B 11 > 95%) was introduced gravitationally in a sequence of H-mode plasma discharges at rates up to ~160 mg s -1 for durations up to 3 s. Boron injection to cumulative amounts ≤0.1 g appeared to improve wall conditions similarly to boronization, with indications of reduced wall fueling, reduced recycling at the outer strike point and reduced impurity content at breakdown. Post-mortem analysis of graphite samples exposed to far scrape-off layer plasma fluxes during boron injection confirm the formation of a B-C layer, with average surface composition B:C ~ 1. The results suggest that injecting boron-rich powders in tokamak plasmas can effectively replenish boron films on carbon plasma facing components to improve wall conditions and extend the duration of the beneficial effects of GDB.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2020

Overview of lithium injection and flowing liquid lithium results from the US–China collaboration on EAST

A multi-institutional team consisting of national labs and universities has been conducting research to understand and control the plasma-material interface (PMI) to improve long pulse discharge control and performance in the EAST device in Hefei, China. One particular focus of the group has been to evaluate the performance of different plasma-facing component (PFC) technologies and materials, particularly lithium. Flowing liquid lithium PFC technologies are currently into their third generation of development and deployment in EAST, demonstrating recycling control and mitigation of edge-localized modes (ELMs). A lithium powder dropper has also been used to control ELMs while a lithium granule injector has demonstrated ELM triggering and pacing. To support this work, the facilities at the Center for Plasma Material Interactions such as HIDRA are being commissioned and utilized to develop/test the technologies before deployment on EAST. This paper will present a summary of the collaborative lithium PMI program on EAST.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗