5,10-Dihydroindolo[3,2-b]indole-Based Copolymers with Alternating Donor and Acceptor Moieties for Organic Photovoltaics
Abstract not provided
Engineering topics
Publications and source records attributed to Ginley, D S.
Abstract not provided
Abstract not provided
Abstract not provided
Gallium-doped zinc oxide (GZO) possesses the electric conductivity, thermal stability, and earth abundance to be a promising transparent conductive oxide replacement for indium tin oxide electrodes in a number of molecular electronic devices, including organic solar cells and organic light emitting diodes. The surface chemistry of GZO is complex and dominated by the hydrolysis chemistry of ZnO, which influences the work function via charge transfer and band bending caused by adsorbates. A comprehensive characterization of the surface chemical composition and electrochemical properties of GZO electrodes is presented, using both solution and surface adsorbed redox probe molecules. The GZO surface is characterized using monochromatic X-ray photoelectron spectroscopy and ultraviolet photoelectron spectroscopy after the following pretreatments: (i) hydriodic acid etch, (ii) potassium hydroxide etch, (iii) RF oxygen plasma etching, and (iv) high-vacuum argon-ion sputtering. The O 1s spectra for the GZO electrodes have contributions from the stoichiometric oxide lattice, defects within the lattice, hydroxylated species, and carbonaceous impurities, with relative near-surface compositions varying with pretreatment. Solution etching procedures result in an increase of the work function and ionization potential of the GZO electrode, but yield different near surface Zn:Ga atomic ratios, which significantly influence charge transfer rates for a chemisorbed probe molecule. The near surface chemical composition is shown to be the dominant factor in controlling surface work function and significantly influences the rate of electron transfer to both solution and tethered probe molecules.
The utilization of radio-frequency (RF) superimposed direct-current (DC) magnetron sputtering deposition on the properties of gallium doped ZnO (GZO) based transparent conducting oxides has been examined. The GZO films were deposited using 76.2 mm diameter ZnO:Ga{sub 2}O{sub 3} (5 at. % Ga vs. Zn) ceramic oxide target on heated non-alkaline glass substrates by varying total power from 60 W to 120 W in steps of 20 W and at various power ratios of RF to DC changing from 0 to 1 in steps of 0.25. The GZO thin films grown with pure DC, mixed approach, and pure RF resulted in conductivities of 2200 {+-} 200 S/cm, 3920 {+-} 600 S/cm, and 3610 {+-} 400 S/cm, respectively. X-ray diffraction showed all films have wurtzite ZnO structure with the c-axis oriented perpendicular to the substrate. The films grown with increasing RF portion of the total power resulted in the improvement of crystallographic texture with smaller full-width half maximum in {chi} and broadening of optical gap with increased carrier concentration via more efficient doping. Independent of the total sputtering power, all films grown with 50% or higher RF power portion resulted in high mobility ({approx}28 {+-} 1 cm{sup 2}/Vs), consistent with observed improvements in crystallographic texture. All films showed optical transmittance of {approx}90% in the visible range.
Hybrid organic/inorganic solar cells have not lived up to their potential because of poor interface properties. Interfacial molecular layers provide a way of adjusting these devices to improve their performance. We have studied a prototypical system involving poly(3-hexylthiophene) (P3HT) on planar zinc oxide (ZnO) films that have been modified with two types of molecules having identical 18-carbon alkyl chain termination and different surface attachments: octadecanethiol (ODT) and octadecyltriethoxysilane (OTES). We examined the functionalized surfaces using water contact angle measurements, Kelvin probe measurements, infrared absorbance spectroscopy, and atomic force microscopy. These have shown that OTES forms disordered incomplete monolayers, while ODT is prone to develop multilayered islands. Both treatments enhance polymer ordering. However, inverted solar cell devices fabricated with these treated interfaces performed very differently. ODT improves the short circuit current (J{sub SC}), open circuit voltage (V{sub OC}), and power conversion efficiency ({eta}), while these parameters all decrease in devices constructed from OTES-treated ZnO. The differences in V{sub OC} are related to modifications of the surface dipole associated with deposition of the two types of alkyl molecules, while changes in J{sub SC} are attributed to a balance between charge transfer blocking caused by the saturated hydrocarbon and the improved hole mobility in the polymer.
We explore the effects of cation off-stoichiometry on structural, electrical, optical, and electronic properties of Co{sub 2}ZnO{sub 4} normal spinel and Co{sub 2}NiO{sub 4} inverse spinel using theoretic and experimental (combinatorial and conventional) techniques, both at thermodynamic equilibrium and in the metastable regime. Theory predicts that nonequilibrium substitution of divalent Zn on nominally trivalent octahedral sites increases net hole density in Co{sub 2}ZnO{sub 4}. Experiment confirms high conductivity and high work function in Co{sub 2}NiO{sub 4} and Zn-rich Co{sub 2}ZnO{sub 4} thin films grown by nonequilibrium physical vapor deposition techniques. High p-type conductivities of Co{sub 2}ZnO{sub 4} (up to 5 S/cm) and Co{sub 2}NiO{sub 4} (up to 204 S/cm) are found over a broad compositional range, they are only weakly sensitive to oxygen partial pressure and quite tolerant to a wide range of processing temperatures. In addition, off-stoichiometry caused by nonequilibrium growth decreases the optical absorption of Co{sub 2}ZnO{sub 4} and Co{sub 2}NiO{sub 4} thin films, although the 500-nm thin films still have rather limited transparency. All these properties as well as high work functions make Co{sub 2}ZnO{sub 4} and Co{sub 2}NiO{sub 4} thin films attractive for technological applications, such as hole transport layers in organic photovoltaic devices or p-type buffer layers in inorganic solar cells.
Abstract not provided
Abstract not provided
Photobleaching rates are investigated for thin films of poly(3-hexylthiophene) (P3HT) blends employing either an indene-C60 bisadduct (ICBA) or [6,6]-phenyl-C61-butyric acid methyl ester (PCBM) as the electron acceptor. Relative to the bisindene, PCBM significantly enhances resistance to photobleaching of the P3HT donor polymer. We tentatively attribute a decrease in the charge transfer rate asthe mechanism responsible for the more rapid photobleaching in the sample containing the bisindene adduct. In order to elucidate the influence of the photobleaching rate on the initial performance of unencapsulated devices, we also monitored the time-dependent behavior for P3HT:fullerene inverted devices. Under conditions of constant illumination, we observe essentially identical behavior indevice performance parameters regardless of the energy levels of the electron acceptor. We conclude that over the time frame measured for these devices, the primary degradation mechanism of the active layer is independent of the electron acceptor, despite the enhanced tolerance to photobleaching it may impart to the donor material.
Metal-Insulator-Metal (MIM) devices are crucial components for applications ranging from optical rectennas for harvesting sunlight to infrared detectors. To date, the relationship between materials properties and device performance in MIM devices is not fully understood, partly due to the difficulty in making and reproducing reliable devices. One configuration that is popular due to itssimplicity and ease of fabrication is the point-contact diode where a metal tip serves as one of the metals in the MIM device. The intrinsic advantage of the point-contact configuration is that it is possible to achieve very small contact areas for the device thereby allowing very high-frequency operation. In this study, precise control over the contact area and penetration depth of anelectrically conductive tip into a metal/insulator combination is achieved using a nanoindenter with in-situ electrical contact resistance measurement capabilities. A diamond probe tip, doped (degeneratively) with boron for conductivity, serves as the point contact and second 'metal' (b-Diamond) of the MIM diode. The base layer consists of Nb/Nb2O5 thin films on Si substrates and serves as thefirst metal /insulator combination of the MIM structure. The current-voltage response of the diodes is measured under a range of conditions to assess the validity and repeatability of the technique. Additionally, we compare the results of this technique to those acquired using a bent-wire approach and find that Nb/Nb2O5/b-Diamond MIM devices show an excellent asymmetry (60-300) and nonlinearityvalues (~6-9). This technique shows great promise for screening metal-insulator combinations for performance without the uncertainty that stems from a typical bent-wire point-contact.
Organic Photovoltaics (OPVs) recently attained power conversion efficiencies that are of interest for commercial production. Consequently, one of the most important unsolved issues facing a new industry is understanding what governs lifetime in organic devices and discovering solutions to mitigate degradation mechanisms. Historically, the active organic components are considered vulnerable to photo-oxidation and represent the primary degradation channel. However, we present several (shelf life and light soaking) studies pointing the relative stability of the active layers and instabilities in commonly used electrode materials. We show that engineering of the hole/electron layer at the electrode can lead to environmentally stable devices even without encapsulation.
In this paper we use the combination of solution deposited liquid precursors and rapid optical processing (ROP) to make CIGS. The ROP process takes less than 1 minute of heating to convert the precursor stack to CIGS. Device made with ROP rival performance of device processed using field assisted simultaneous synthesis and transfer FASST{reg_sign} processing.
The purpose of this CRADA was to combine the strengths of NREL and Evergreen Solar in the area of ink jet printing to develop a new manufacturing technology necessary to produce Si solar cells based on ribbon technology comparable to or exceeding current technologies.
No abstract prepared.
The NREL/Evident team will develop techniques to fabricate thin film solar cells where the absorption layers comprising the solar cells are derived from sintered semiconductor quantum dots.
NREL will perform deposition and testing of various dielectrics on high-temperature superconductors.