Search NASA⌕ Search

Engineering topics

Giridharagopal, Rajiv

Publications and source records attributed to Giridharagopal, Rajiv.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Degradation Dynamics of Perovskite Solar Cells Under Fixed Reverse Current Injection

Previous studies of reverse-bias stability in perovskite solar cells have focused primarily on voltage controlled reverse-bias tests. Here we instead present an investigation of perovskite solar cell degradation under well-defined, constant reverse-current stress. We show that the choice of hole-transport layer dictates the dominant degradation pathway: cells using thick poly(triphenylamine) (PTAA) layers with better indium-doped tin oxide (ITO) coverage can tolerate high reverse bias but quickly undergo catastrophic breakdown under fixed reverse current near their one-sun maximum power-point. In contrast, cells modified with the phosphonic-acid interface layer MeO-2PACz, with poorer ITO coverage compared to PTAA, exhibit soft, gradual, and largely recoverable degradation, regardless of the shading conditions. For MeO-2PACz devices, degradation increases with both current magnitude and duration. Importantly, when normalized by injected charge (current times duration), lower currents applied over longer times cause more severe degradation than higher currents over shorter periods. Combining electrical measurements with spatially resolved photoluminescence imaging, we argue against shunt formation and instead support an ion- and charge-mediated interfacial electrochemical degradation mode.

Applied Physics (physics.app-ph)↗
DOE OSTI2024

Optical tuning of the diamond Fermi level measured by correlated scanning probe microscopy and quantum defect spectroscopy

Quantum technologies based on quantum point defects in crystals require control over the defect charge state. Here we tune the charge state of shallow nitrogen-vacancy and silicon-vacancy centers by locally oxidizing a hydrogenated surface with moderate optical excitation and simultaneous spectral monitoring. The loss of conductivity and change in work function due to oxidation are measured in atmosphere using conductive atomic force microscopy and Kelvin probe force microscopy (KPFM). We correlate these scanning probe measurements with optical spectroscopy of the nitrogen-vacancy and silicon-vacancy centers created via implantation 15–25 nm beneath the diamond surface and annealing. The observed charge state of the defects as a function of optical exposure demonstrates that laser oxidation provides a way to precisely tune the Fermi level over a range of at least 2.00 eV. We also observe a significantly larger oxidation rate for implanted surfaces compared to unimplanted surfaces under ambient conditions. Here, combined with knowledge of the electron affinity of a surface, these results suggest KPFM is a powerful, high-spatial-resolution technique to advance surface Fermi level engineering for charge stabilization of quantum defects.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Local Background Hole Density Drives Nonradiative Recombination in Tin Halide Perovskites

In this study, we use multimodal microscopy to study carrier recombination in semiconducting tin halide perovskite films based on PEA 0.2 FA 0.8 SnI 3 (PEA = phenethylammonium; FA = formamidinium). We use the observation of pseudo-first-order photoluminescence (PL) decay kinetics to establish a method for quantifying the hole dopant level and nonradiative recombination rate constant. We find that untreated PEA 0.2 FA 0.8 SnI 3 films exhibit large hole doping concentrations of p 0 ≈ 10 19 cm –3 , which is reduced to p 0 ≈ 10 16 cm –3 after SnF 2 treatment. While it is well-known that the radiative recombination rates are increased with p 0 , we reveal that the nonradiative rate is also increased. We find that p-type regions in untreated PEA 0.2 FA 0.8 SnI 3 films are centers for nonradiative recombination, which are diminished in films with p 0 ≈ 10 16 cm –3 . We discover significant PL heterogeneity even in PEA 0.2 FA 0.8 SnI 3 films with moderate dopant levels, suggesting that new strategies to eliminate deleterious defects in PEA 0.2 FA 0.8 SnI 3 must be developed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Kinetic Suppression of Photoinduced Halide Migration in Wide Bandgap Perovskites via Surface Passivation

In this work, we study the kinetics of photoinduced halide migration in FA 0.8 Cs 0.2 Pb(I 0.8 Br 0.2 ) 3 wide (~1.69 eV) bandgap perovskites and show that halide migration slows down following surface passivation with (3-aminopropyl) trimethoxysilane (APTMS). We use scanning Kelvin probe microscopy (SKPM) to probe the contact potential difference (CPD) shift under illumination and the kinetics of surface potential relaxation in the dark. Our results show that APTMS-passivated perovskites exhibit a smaller CPD shift under illumination and a slower surface potential relaxation in the dark. We compare the evolution of the photoluminescence spectra of APTMS-passivated and unpassivated perovskites under illumination. We find that APTMS-passivated perovskites exhibit more than 5 times slower photoluminescence red-shift, consistent with the slower surface potential relaxation as observed by SKPM. In conclusion, these observations provide evidence for kinetic suppression of photoinduced halide migration in APTMS-passivated samples, likely due to reduced halide vacancy densities, opening avenues to more efficient and stable devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Vapor-Deposited n = 2 Ruddlesden–Popper Interface Layers Aid Charge Carrier Extraction in Perovskite Solar Cells

Interfacial passivation with bulky organic cations such as phenetylammonium iodide has enabled high performance for metal halide perovskite optoelectronic devices. However, the homogeneity of these interfaces and their formation dynamics are poorly understood. Here we study how Ruddlesden-Popper 2D phases form at a 3D perovskite interface when the 2D precursors are introduced via solution or via vapor. When using vapor deposition, we observe uniform coverage of the capping layer and the formation of a predominantly n = 2 Ruddlesden-Popper phase. In contrast, when using solution deposition, we observe the presence of a mixture of n = 2 and n = 1 in the film and the formation of aggregates of the organic cations. As a result of the better phase purity and uniformity, vapor deposition enables higher median solar cell performance with narrower distribution compared to solution-treated films. This study provides fundamental information that the perovskite community can use to better design capping layers to achieve higher charge extraction efficiencies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Hydration of a Side-Chain-Free n-Type Semiconducting Ladder Polymer Driven by Electrochemical Doping

Here, we study the organic electrochemical transistors (OECTs) performance of the ladder polymer, poly(benzimidazobenzophenanthroline) (BBL) in an attempt to better understand how an apparently hydrophobic side-chain-free polymer is able to operate as an OECT with favorable redox kinetics in an aqueous environment. We examine two BBLs of different molecular masses from different sources. Both BBLs show significant film swelling during the initial reduction step. By combining electrochemical quartz crystal microbalance (eQCM) gravimetry, in-operando atomic force microscopy (AFM), and both ex-situ and in-operando grazing incidence wide-angle x-ray scattering (GIWAXS), we provide a detailed structural picture of the electrochemical charge injection process in BBL in the absence of any hydrophilic side-chains. Compared with ex-situ measurements, inoperando GIWAXS shows both more swelling upon electrochemical doping than has previously been recognized, and less contraction upon dedoping. The data show that BBL films undergo an irreversible hydration driven by the initial electrochemical doping cycle with significant water retention and lamellar expansion that persists across subsequent oxidation/reduction cycles. This swelling creates a hydrophilic environment that facilitates the subsequent fast hydrated ion transport in the absence of the hydrophilic side-chains used in many other polymer systems. Due to its rigid ladder backbone and absence of hydrophilic side-chains, the primary BBL water uptake does not significantly degrade the crystalline order, and the original dehydrated, unswelled state can be recovered after drying. The combination of doping induced hydrophilicity and robust crystalline order leads to efficient ionic transport and good stability.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

(3-Aminopropyl)trimethoxysilane Surface Passivation Improves Perovskite Solar Cell Performance by Reducing Surface Recombination Velocity

We demonstrate reduced surface recombination velocity (SRV) and enhanced power-conversion efficiency (PCE) in mixed-cation mixed-halide perovskite solar cells by using (3-aminopropyl)trimethoxysilane (APTMS) as a surface passivator. We show the APTMS serves to passivate defects at the perovskite surface, while also decoupling the perovskite from detrimental interactions at the C 60 interface. We measure a SRV of ~125 ± 14 cm/s, and a concomitant increase of ~100 meV in quasi-Fermi level splitting in passivated devices compared to the controls. We use time-resolved photoluminescence and excitation-correlation photoluminescence spectroscopy to show that APTMS passivation effectively suppresses non-radiative recombination. We show that APTMS improves both the fill factor and open-circuit voltage (V OC ), increasing V OC from 1.03 V for control devices to 1.09 V for APTMS-passivated devices, and leads to a PCE increase from 15.90% to 18.03%. Here, we attribute the enhanced performance to reduced defect density resulting in suppressed nonradiative recombination and lower SRV at the perovskite/transport layer interface.

14 SOLAR ENERGY↗
DOE OSTI2022

Deterministic fabrication of 3D/2D perovskite bilayer stacks for durable and efficient solar cells

Realizing solution-processed heterostructures is a long-enduring challenge in halide perovskites because of solvent incompatibilities that disrupt the underlying layer. By leveraging the solvent dielectric constant and Gutmann donor number, we could grow phase-pure two-dimensional (2D) halide perovskite stacks of the desired composition, thickness, and bandgap onto 3D perovskites without dissolving the underlying substrate. Characterization reveals a 3D–2D transition region of 20 nanometers mainly determined by the roughness of the bottom 3D layer. Thickness dependence of the 2D perovskite layer reveals the anticipated trends for n-i-p and p-i-n architectures, which is consistent with band alignment and carrier transport limits for 2D perovskites. Here we measured a photovoltaic efficiency of 24.5%, with exceptional stability of T 99 (time required to preserve 99% of initial photovoltaic efficiency) of >2000 hours, implying that the 3D/2D bilayer inherits the intrinsic durability of 2D perovskite without compromising efficiency.

14 SOLAR ENERGY↗
DOE OSTI2022

A Robust Neural Network for Extracting Dynamics from Electrostatic Force Microscopy Data

Advances in scanning probe microscopy (SPM) methods such as time-resolved electrostatic force microscopy (trEFM) now permit the mapping of fast local dynamic processes with high resolution in both space and time, but such methods can be time-consuming to analyze and calibrate. Here, we design and train a regression neural network (NN) that accelerates and simplifies the extraction of local dynamics from SPM data directly in a cantilever-independent manner, allowing the network to process data taken with different cantilevers. We validate the NN’s ability to recover local dynamics with a fidelity equal to or surpassing conventional, more time-consuming, calibrations using both simulated and real microscopy data. We apply this method to extract accurate photoinduced carrier dynamics on n = 1 butylammonium lead iodide, a halide perovskite semiconductor film that is of interest for applications in both solar photovoltaics and quantum light sources. Lastly, we use SHapley Additive exPlanations to evaluate the robustness of the trained model, confirm its cantilever-independence, and explore which parts of the trEFM signal are important to the network.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Reduced Surface Recombination Velocity in Mixed-Cation Mixed-Halide Hybrid Perovskite Devices Leads to Improved Open-Circuit Voltage

Surface recombination plays an important role in perovskite solar cell performance.Despite rapid progress, the record power conversion efficiency (PCE, ~ 25.7%) for perovskite single-junction solar cells still lags behind its theoretical limit (~ 32%), largely due to the open circuit voltage (VOC) deficit that results from non-radiative recombination at the bulk of perovskite films and the interfaces between perovskite and transport layers. In this work, we show that (3-aminopropyl)trimethoxysilane (APTMS) surface passivation can reduce the surface recombination velocities (SRVs) of perovskite solar cells, thus improving device VOC and PCE.

perovskite solar cell, surface recombination, surf↗