Search NASA⌕ Search

Engineering topics

Glatt, C. R.

Publications and source records attributed to Glatt, C. R..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

ODIN system technology module library, 1972 - 1973

ODIN/RLV is a digital computing system for the synthesis and optimization of reusable launch vehicle preliminary designs. The system consists of a library of technology modules in the form of independent computer programs and an executive program, ODINEX, which operates on the technology modules. The technology module library contains programs for estimating all major military flight vehicle system characteristics, for example, geometry, aerodynamics, economics, propulsion, inertia and volumetric properties, trajectories and missions, steady state aeroelasticity and flutter, and stability and control. A general system optimization module, a computer graphics module, and a program precompiler are available as user aids in the ODIN/RLV program technology module library.

Hague, D. S.↗
NASA NTRS1977

Development of the engineering design integration (EDIN) system: A computer aided design development

The EDIN (Engineering Design Integration) System which provides a collection of hardware and software, enabling the engineer to perform man-in-the-loop interactive evaluation of aerospace vehicle concepts, was considered. Study efforts were concentrated in the following areas: (1) integration of hardware with the Univac Exec 8 System; (2) development of interactive software for the EDIN System; (3) upgrading of the EDIN technology module library to an interactive status; (4) verification of the soundness of the developing EDIN System; (5) support of NASA in design analysis studies using the EDIN System; (6) provide training and documentation in the use of the EDIN System; and (7) provide an implementation plan for the next phase of development and recommendations for meeting long range objectives.

Glatt, C. R.↗
NASA NTRS1976

EDIN design study alternate space shuttle booster replacement concepts. Volume 1: Engineering analysis

The use of a recoverable liquid rocket booster (LRB) system to replace the existing solid rocket booster (SRB) system for the shuttle was studied. Historical weight estimating relationships were developed for the LRB using Saturn technology and modified as required. Mission performance was computed using February 1975 shuttle configuration groundrules to allow reasonable comparison of the existing shuttle with the study designs. The launch trajectory was constrained to pass through both the RTLS/AOA and main engine cut off points of the shuttle reference mission 1. Performance analysis is based on a point design trajectory model which optimizes initial tilt rate and exoatmospheric pitch profile. A gravity turn was employed during the boost phase in place of the shuttle angle of attack profile. Engine throttling add/or shutdown was used to constrain dynamic pressure and/or longitudinal acceleration where necessary. Four basic configurations were investigated: a parallel burn vehicle with an F-1 engine powered LRB; a parallel burn vehicle with a high pressure engine powered LRB; a series burn vehicle with a high pressure engine powered LRB. The relative sizes of the LRB and the ET are optimized to minimize GLOW in most cases.

Demakes, P. T.↗
NASA NTRS1976

EDIN design study alternate space shuttle booster replacement concepts. Volume 2: Design simulation results

Historical weight estimating relationships were developed for the liquid rocket booster (LRB) using Saturn technology, and modified as required to support the EDIN05 study. Mission performance was computed using February 1975 shuttle configuration groundrules to allow reasonable comparison of the existing shuttle with the EDIN05 designs. The launch trajectory was constrained to pass through both the RTLS/AOA and main engine cut-off points. Performance analysis was based on a point design trajectory model which optimized initial tilt rate and exo-atmospheric pitch profile. A gravity turn was employed during the boost phase in place of the shuttle angle-of-attack profile. Engine throttling add/or shutdown was used to constrain dynamic pressure and/or longitudinal acceleration where necessary.

Demakes, P. T.↗
NASA NTRS1975

Prediction of sonic boom from experimental near-field overpressure data. Volume 1: Method and results

A computerized procedure for predicting sonic boom from experimental near-field overpressure data has been developed. The procedure extrapolates near-field pressure signatures for a specified flight condition to the ground by the Thomas method. Near-field pressure signatures are interpolated from a data base of experimental pressure signatures. The program is an independently operated ODIN (Optimal Design Integration) program which obtains flight path information from other ODIN programs or from input.

Glatt, C. R.↗
NASA NTRS1975

ODIN: Optimal design integration system

The report provides a summary of the Optimal Design Integration (ODIN) System as it exists at Langley Research Center. A discussion of the ODIN System, the executive program and the data base concepts are presented. Two examples illustrate the capabilities of the system which have been exploited. Appended to the report are a summary of abstracts for the ODIN library programs and a description of the use of the executive program in linking the library programs.

Glatt, C. R.↗
NASA NTRS1975

Computer graphics application in the engineering design integration system

The computer graphics aspect of the Engineering Design Integration (EDIN) system and its application to design problems were discussed. Three basic types of computer graphics may be used with the EDIN system for the evaluation of aerospace vehicles preliminary designs: offline graphics systems using vellum-inking or photographic processes, online graphics systems characterized by direct coupled low cost storage tube terminals with limited interactive capabilities, and a minicomputer based refresh terminal offering highly interactive capabilities. The offline line systems are characterized by high quality (resolution better than 0.254 mm) and slow turnaround (one to four days). The online systems are characterized by low cost, instant visualization of the computer results, slow line speed (300 BAUD), poor hard copy, and the early limitations on vector graphic input capabilities. The recent acquisition of the Adage 330 Graphic Display system has greatly enhanced the potential for interactive computer aided design.

Glatt, C. R.↗
NASA NTRS1974

The engineering design integration (EDIN) system

A digital computer program complex for the evaluation of aerospace vehicle preliminary designs is described. The system consists of a Univac 1100 series computer and peripherals using the Exec 8 operating system, a set of demand access terminals of the alphanumeric and graphics types, and a library of independent computer programs. Modification of the partial run streams, data base maintenance and construction, and control of program sequencing are provided by a data manipulation program called the DLG processor. The executive control of library program execution is performed by the Univac Exec 8 operating system through a user established run stream. A combination of demand and batch operations is employed in the evaluation of preliminary designs. Applications accomplished with the EDIN system are described.

Glatt, C. R.↗
NASA NTRS1974

Geometry Technology Module (GTM). Volume 1: Engineering description and utilization manual

The geometry technology module (GTM) is described as a system of computerized elements residing in the engineering design integration system library developed for the generation, manipulation, display, computation of mass properties, and data base management of panelled geometry. The GTM is composed of computer programs and associated data for performing configuration analysis on geometric shapes. The program can be operated in batch or demand mode and is designed for interactive use.

Reiners, S. J.↗
NASA NTRS1974

The DLG processor: A data management executive for the engineering design integration (EDIN) system. Volume 1: Engineering description and utilization manual

The DLG processor is a Univac 1100 series computer program designed to read, modify, manipulate, and replace symbolic images. DLG is controlled by a set of user supplied directives and operates from a data base of stratified information which can be merged with the symbolic images. Data bases can be constructed and maintained in the mass storage media using the DLG directive language.

Glatt, C. R.↗
NASA NTRS1974

PLOTTER: An independent computer program for the generation of graphical displays

A computer program is described for generating graphical information from input data or auxiliary analysis programs on a variety of graphical devices. Options are presented for tabulating the data in columnar format and for plotting auxiliary text in the vicinity of the plotted information. Display device selection is accomplished by interfacing the basic computer code through routines which convert the internally generated plot vectors to hardware commands for the display device. The plotting techniques employed in the computer program are discussed. User's instructions are presented with examples which illustrate the use of the program in generating plotted information from various sources and presenting the information in alternate plot formats. Technical discussion of the computer code is presented giving the physical characteristics, computer loading instructions and descriptions of the subroutines.

Glatt, C. R.↗
NASA NTRS1974

WAATS: A computer program for Weights Analysis of Advanced Transportation Systems

A historical weight estimating technique for advanced transportation systems is presented. The classical approach to weight estimation is discussed and sufficient data is presented to estimate weights for a large spectrum of flight vehicles including horizontal and vertical takeoff aircraft, boosters and reentry vehicles. A computer program, WAATS (Weights Analysis for Advanced Transportation Systems) embracing the techniques discussed has been written and user instructions are presented. The program was developed for use in the ODIN (Optimal Design Integration System) system.

Glatt, C. R.↗
NASA NTRS1974

Computer-aided space shuttle orbiter wing design study

An analytical and experimental investigation has been made to provide a space shuttle orbiter wing design that met the guideline requirements of landing performance, stability, and hypersonic trim for a specified center-of-gravity envelope. The analytical study was facilitated by the use of the Optimal Design Integration system (ODIN) and the experimental part of the investigation was conducted in the Langley low-turbulence pressure tunnel and the Langley continuous-flow hypersonic tunnel.

Phillips, W. P.↗