International perspectives on glass waste form development for low-level and intermediate-level radioactive waste
Not Available
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
Engineering topics
Goel, Ashutosh
Publications and source records attributed to Goel, Ashutosh.
Modeling viscosity of commercial glass melts: Adam–Gibbs equation and Gaussian process regression
Not Available
36 MATERIALS SCIENCE↗
Iodine Capture by Ag-Loaded Solid Sorbents Followed by Ag Recycling and Iodine Immobilization: An End-to-End Process
Here, this article demonstrates the complete process of I 2(g) capture using Ag-exchanged faujasite (AgX) and Ag-exchanged mordenite (AgZ) zeolite sorbents, the recovery of Ag for recyclability of iodine capture, and the immobilization of iodide (from the elution process) into an iodosodalite waste form, which is chemically and environmentally stable. The gaseous iodine, I 2(g) , was captured in the AgX via chemisorption by Ag and converted to AgI within the aluminosilicate zeolite frameworks. The elution reaction in Na 2 S resulted in the precipitation of Ag 2 S and dissolution of I – and Na + into the aqueous solution, where powdered sorbent showed higher conversion efficiency than the granular form, which is attributed to Na 2 S-solution diffusion limitations in the granules. The Ag 2 S-containing aluminosilicate precipitates were filtered out of the solution, and the filtrate (aqueous solution) was used to synthesize iodosodalite to immobilize iodide. The iodine capture using the recovered Ag 2 S-containing sorbents shows equivalent iodine loadings to the AgX starting material of Q e = 0.355 g/g for powdered material and 0.255 g/g for granular material, demonstrating the potential recycling of Ag for iodine capture as Ag 2 S-based sorbents.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Corrosion behavior of Monofrax K-3 refractory in borosilicate-based model low activity waste glass melts
Owing to its good chemical and thermal durabilities at high temperatures, Monofrax K-3 refractory is widely used in nuclear waste vitrification as a lining material in melting vessels. However, the corrosion of K-3 refractory during the vitrification of nuclear waste is a serious problem because it affects the melter's safety, performance, and lifetime. Therefore, in the present study, we have focused on unearthing the impact of glass network formers, such as SiO 2 , B 2 O 3 , and Al 2 O 3 , in a model nuclear waste glass composition on the corrosion of Monofrax K-3 refractory. The corrosion tests have been performed per ASTM C621 at 1150°C for 5 days. The dimensional measurements on corroded K-3 refractory suggest that Al 2 O 3 and SiO 2 tend to reduce the refractory corrosion (neck loss), with the effect of Al 2 O 3 being significant. A corroded region on the K-3 refractory at the melt–refractory interface is observed. The corrosion occurs via a coupling of the melt infiltration induced by a capillary effect and the dissolution of Al, Mg, and Fe components from K-3 into the melt through chemical reactions. A Cr-rich layer is retained on the glass contact surface of the corroded K-3 refractory.
36 MATERIALS SCIENCE↗
Separated waste stream immobilization of iodine and off-gas caustic scrubber solution (Final Report)
In this work, the approach was to immobilize the CS solution in a glass-bonded composite of cancrinite/sodalite. The synthesis of ceramic waste forms was accomplished by low-temperature (~90°C) processes developed by the team in the framework of a previous NEUP project. By building on our earlier efforts for iodine waste forms, we minimized the schedule and technical risk while still providing novel process demonstrations for the off-gas waste forms. In the case of AgI-based sorbents, a proof-of-concept stripping process was shown to remove iodine from AgI by converting it to NaI(aq) followed by immobilization of these ions in iodosodalite (ISOD), which could be glass-bonded in the same way as for the CS solution cancrinite/sodalite powders.
11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
Impact of non‐framework cation mixing on the structure and crystallization behavior of model high‐level waste glasses
Abstract Spinel crystallization is known to be detrimental to the operation of Joule heated ceramic melters during the vitrification of iron‐rich high‐level nuclear wastes (HLW) into borosilicate glasses. The literature on this subject focuses on tackling the problem by developing empirical constraints to design compositions, which limit the fraction of spinels formed in the melter or by developing empirical models to predict the settling behavior of spinels in the melter as a function of the glass composition. While these empirical models can predict the behavior of most of the compositions, they are not failsafe as there are always some compositions, whose behavior is beyond the predictive ability of these models. This can lead to undesirable situations during the vitrification of the nuclear waste, and therefore an in‐depth investigation of the chemo‐structural descriptors controlling the crystallization behavior in these glasses is warranted. Accordingly, the present study aims to understand the impact of non‐framework cation mixing (i.e., Li + /Na + and Ca 2+ /Na + ) on the structure (through Raman spectroscopy and Mössbauer spectroscopy) and crystallization behavior (through XRD, SEM‐EDS, and vibrating sample magnetometry) of iron‐rich model HLW glasses in the system: (mol.%) x M y O–(25− x ) Na 2 O–9.12 B 2 O 3 –6.4 Al 2 O 3 –51.25 SiO 2 –7.22 Fe 2 O 3 –0.38 MnO–0.08 Cr 2 O 3 –0.55NiO (M y O = Li 2 O or CaO).
Balasubramanya, Nikhila↗
A Comparative Study on the Effect of Zr, Sn, and Ti on the Crystallization Behavior of Nepheline Glass
In alkali aluminosilicate glasses, additions of 4+ cations like Zr and Ti are often added to promote crystallization. In this study, Zr, Ti, or Sn are progressively substituted for Si in nepheline (NaAlSiO4) glass to determine their impact on the crystallization behavior. For glasses homogeneous on quenching, up to NaAlZr0.075Si0.925O4, NaAlSn0.100Si0.900O4, and NaAlTi0.300Si0.700O4, respectively, crystallization temperatures were investigated by thermal analysis. A subset of compositions was subjected to additional thermal analysis, varying heating rate and particle size, to investigate the subtleties of crystallization behavior. Subsequent heat treatment of glass powders was performed to maximize crystallization, and glass-ceramic microstructure was assessed by optical microscopy and electron microprobe, while crystalline phases were determined by X-ray diffraction. In all cases the major crystalline phase was orthorhombic carnegieite, which accommodated Ti in its structure but not Zr or Sn, and excess 4+ cations formed MO2, i.e., brookite, baddeleyite, and cassiterite, respectively.
Nienhuis-Marcial, Emily T.↗
Dissolution kinetics of a sodium borosilicate glass in Tris buffer solutions: impact of Tris concentration and acid (HCl/HNO 3 ) identity
Here, understanding the corrosion behavior of glasses in near-neutral environments is crucial for many technologies including glasses for regenerative medicine and nuclear waste immobilization. To maintain consistent pH values throughout experiments in the pH = 7 to 9 regime, buffer solutions containing tris(hydroxymethyl)aminomethane (“Tris”, or sometimes called THAM) are recommended in ISO standards 10993-14 and 23317 for evaluating biomaterial degradation and utilized throughout glass dissolution behavior literature—a key advantage being the absence of dissolved alkali/alkaline earth cations (i.e. Na + or Ca 2+ ) that can convolute experimental results due to solution feedback effects. Although Tris is effective at maintaining the solution pH, it has presented concerns due to the adverse artificial effects it produces while studying glass corrosion, especially in borosilicate glasses. Therefore, many open questions still remain on the topic of borosilicate glass interaction with Tris-based solutions. We have approached this topic by studying the dissolution behavior of a sodium borosilicate glass in a wide range of Tris-based solutions at 65 °C with varied acid identity (Tris–HCl vs. Tris–HNO 3 ), buffer concentration (0.01 M to 0.5 M), and pH (7–9). The results have been discussed in reference to previous studies on this topic and the following conclusions have been made: (i) acid identity in Tris-based solutions does not exhibit a significant impact on the dissolution behavior of borosilicate glasses, (ii) ~0.1 M Tris-based solutions are ideal for maintaining solution pH in the absence of obvious undesirable solution chemistry effects, and (iii) Tris–boron complexes can form in solution as a result of glass dissolution processes. The complex formation, however, exhibits a distinct temperature-dependence, and requires further study to uncover the precise mechanisms by which Tris-based solutions impact borosilicate glass dissolution behavior.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Structural drivers controlling sulfur solubility in alkali aluminoborosilicate glasses
Abstract If the direct feed approach to vitrify the Hanford's tank waste is implemented, the low activity waste (LAW) will comprise higher concentrations of alkali/alkaline‐earth sulfates than expected under the previously proposed vitrification scheme. To ensure a minimal impact of higher sulfate concentrations on the downstream operations and overall cost of vitrification, advanced glass formulations with enhanced sulfate loadings (solubility) are needed. While, the current sulfate solubility predictive models have been successful in designing LAW glasses with sulfate loadings <2 wt.%, it will be difficult for them to design glass compositions with enhanced loadings due to our limited understanding of the fundamental science governing these processes. In this pursuit, this article unearths the underlying compositional and structural drivers controlling the sulfate solubility in model LAW glasses. It has been shown that the preferentially removes non‐framework cations from the modifier sites in the silicate network, thus, leading to the polymerization in the glass network via the formation of ring‐structured borosilicate units. Furthermore, though the sulfate solubility slightly decreases with increasing Li + /Na + in the glasses, the prefers to be charge compensated by Na + , as it is easier for to break Na–O bonds instead of Li–O bonds.
Xu, Xinyi↗
Multiscale Investigation of the Mechanisms Controlling the Corrosion of Borosilicate Glasses in Hyper-Alkaline Media
The overarching goal of the present multiscale investigation is to unearth the kinetics and mechanisms of corrosion of borosilicate glasses in hyper-alkaline (pH = 13) environments as a function of their chemical composition. Accordingly, a series of 3- to 6-component borosilicate glasses have been designed starting from Na 2 O–B 2 O 3 –SiO 2 ternary, wherein the compositional complexity has been added in a systematic tiered approach, finally resulting in the composition of the well-known international simple glass (ISG). Tetramethylammonium hydroxide (TMAH), one of the most widely used alkaline etchant in the glass and electronics industry, has been used as the corrosion media. A series of state-of-the-art characterization techniques including magic angle spinning nuclear magnetic resonance spectroscopy, X-ray photoelectron spectroscopy, inductively coupled plasma optical emission spectroscopy, elastic recoil detection analysis, and high-resolution transmission electron microscopy have been employed to unearth the compositional dependence of glass corrosion in hyper-alkaline environments. The glass compositions underwent congruent corrosion in the forward rate regime, whereas the controlling mechanism of corrosion in the residual rate regime depends on the presence/absence of Ca in the surrounding environment and can be explained on the basis of the dissolution–reprecipitation model. The dependence of corrosion kinetics and the chemistry of alteration products (in the residual rate regime) on the glass composition have been discussed. Here, the results presented in this contribution will ultimately supplement the scientific literature attempting to understand the fundamental science governing the aqueous corrosion of silicate-based glass chemistries and add to the growing database required to develop non-empirical predictive models for designing glasses with controlled dissolution rates.
12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
Ruthenium solubility and its impact on the crystallization behavior and electrical conductivity of MoO 3 -containing borosilicate-based model high-level nuclear waste glasses
The present study focuses on investigating the solubility of RuO 2 in a borosilicate-based model high-level waste glass and understanding its impact on the crystallization behavior and electrical conductivity of the resulting vitrified waste forms. The solubility limit of RuO 2 in the investigated glass composition has been determined to be 460 ppm by weight. The higher concentration of RuO 2 results in sub-micron sized Ru-rich inclusions in the glassy matrix, which eventually agglomerate to form needle-like and polyhedral RuO 2 crystals. It is observed that RuO 2 selectively promotes the crystallization of the rare-earth apatite phase over the powellite phase. The as-synthesized RuO 2 -containing glasses exhibit semiconducting behavior with a similar level of electrical conductivity below the glass transition. Here, the percolation of non-uniformly distributed RuO 2 inclusions may result in a formation of short-range low-resistive conduction pathways in the host glass matrix leading to an apparent metallic-like behavior of selected thin samples with the highest ruthenium content.
36 MATERIALS SCIENCE↗
Why does B 2 O 3 suppress nepheline (NaAlSiO 4 ) crystallization in sodium aluminosilicate glasses?
Addition of B 2 O 3 in aluminosilicate glasses leads to structural changes that cause increase in liquidus viscosity and thereby suppresses crystallization.
Deshkar, Ambar↗