Non-radioisotopic gamma-ray calibration source for radiation detection instruments
Explore the source record for details and available documents.
Engineering topics
Publications and source records attributed to Gomez, Edgar.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
High-quality bi-concave 2D focusing diamond X-ray lenses of apex-radius R = 100 µm produced via laser-ablation and improved via mechanical polishing are presented here. Both for polished and unpolished individual lenses and for stacks of ten lenses, the remaining figure errors determined using X-ray speckle tracking are shown and these results are compared with those of commercial R = 50 µm beryllium lenses that have similar focusing strength and physical aperture. For two stacks of ten diamond lenses (polished and unpolished) and a stack of eleven beryllium lenses, this paper presents measured 2D beam profiles out of focus and wire scans to obtain the beam size in the focal plane. These results are complemented with small-angle X-ray scattering (SAXS) measurements of a polished and an unpolished diamond lens. Again, this is compared with the SAXS of a beryllium lens. The polished X-ray lenses show similar figure errors to commercially available beryllium lenses. While the beam size in the focal plane is comparable to that of the beryllium lenses, the SAXS signal of the polished diamond lenses is considerably lower.
Explore the source record for details and available documents.
Quantum efficiency (QE), intrinsic emittance, and robustness are the three most important figures of merit for photocathodes, the first two determine the ultimate achievable brightness of an electron beam, and the third one directly correlates with the complications of a beamline design. Nitrogen-incorporated ultrananocrystalline diamond [(N)UNCD] materials are promising candidates for photocathode applications due to their remarkable electron emission performance as well as the moderate vacuum requirement. Two (N)UNCD photocathodes have been characterized in a realistic RF gun environment with the nicely balanced performance of all three figures of merit. In this work, the QE of the first (N)UNCD cathode (stored in air for two years before the test) was found to be 3.8 x 10 –4 using a 262 nm UV laser and a cathode surface field of 30MV/m. It was found that the QE of the second (N)UNCD sample (grown days before the test) was nearly the same and, therefore, demonstrates the exceptional environmental tolerance of the material. The intrinsic emittance of (N)UNCD was measured to be 1.00 μm/mm.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
develop an inexpensive accelerating structure with a high gradient and high shunt impedance. Euclid Techlabs proposes to optimize this technology (based on a successful accelerating structure with distributed coupling developed at SLAC) for industrial applications and serial production. Future colliders require high gradient and high efficiency accelerating structures (high shunt impedance). The SLAC accelerator laboratory recently developed a series of accelerating structures with distributed coupling. Such a structure includes one or more parallel waveguides which are loaded by accelerating cavities. This approach allows configurations where no RF power is flowing axially through the accelerating cavity while maintaining a traveling RF wave through the cross-section of the accelerating structure. In this case the accelerating cavities are isolated at the beam pipe. Conventional traveling wave structures typically couple the RF power through the beam pipe. This feature constrains the cavity shunt impedance to relatively small values. For this reason, the distributed coupling design improves efficiency while reducing cost and improving the operational flexibility of particle accelerators. High gradient operation poses the risk of having a high breakdown rates. In traditional standing and traveling wave structures, RF power flows through the accelerating cells. For distributed coupling structures, this risk is reduced because the absence of power flow through the accelerating cavity allows configurations where no power flows through the beam pipe. Finally, the distributed coupling accelerating structure design allows fabricating structures in two halves. This significantly reduces the complexity of machining, brazing and tuning.
The x-ray free electron laser (x-FEL) efficiency, measured as a fraction of the electron beam power converted into light, is typically below 0.1% for most of the x-FEL facilities presently in operation. Undulator tapering techniques can be used to improve the conversion efficiency by 1-2 orders of magnitude. At present there are no robust tapered undulator x-FEL schemes operating at 10% efficiency. Such development will be a breakthrough for the x-FEL community.
Explore the source record for details and available documents.