Search NASA⌕ Search

Engineering topics

Gong, Mingyu

Publications and source records attributed to Gong, Mingyu.

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Bridging microscale to macroscale mechanical property measurements of FeCrAl alloys by crystal plasticity modeling

FeCrAl alloys are candidates for accident tolerant fuel cladding of light water reactors. In this work, a microstructure- and temperature-dependent crystal plasticity model is employed to bridge microscale to macroscale mechanical property measurements of FeCrAl alloys. With the visco-plastic self-consistent (VPSC) polycrystal plasticity framework, a mechanism-based single crystal plasticity (MSCP) model adopts the Arrhenius type rate equation to describe the dependence of the critical resolved shear stress for dislocation slips on their temperature-dependent intrinsic frictional resistance and the microstructure-dependent irradiation hardening. The intrinsic frictional resistance associated with {110}<111> and {112}<111> slip systems were measured by in-situ micromechanical testing on unirradiated/irradiated samples at 25-500 °C. The irradiation hardening is estimated by the Bacon-Kocks-Scattergood (BKS) model with density and size of radiation-induced defects measured from microstructural characterization. Several features associated with thermo-mechanical behavior of unirradiated/irradiated polycrystalline FeCrAl alloys are captured. High density of deformation-induced dislocations and radiation-induced defects results in obvious hardening at room temperature, which is weakened at high temperature, and facilitates damage evolution during deformation. Moreover, both high temperature and radiation-induced defects, which facilitate dislocation multiplication, trigger large hardening rate. Finally, the proposed method together with application of accelerator-based ion irradiation technique is a surrogate approach to simulate neutron damage, improving the efficiency associated with evaluation of mechanical properties of FeCrAl alloys exposed to temperature, stress and radiation conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Visualization and validation of twin nucleation and early-stage growth in magnesium

The abrupt occurrence of twinning when Mg is deformed leads to a highly anisotropic response, making it too unreliable for structural use and too unpredictable for observation. Here, we describe an in-situ transmission electron microscopy experiment on Mg crystals with strategically designed geometries for visualization of a long-proposed but unverified twinning mechanism. Combining with atomistic simulations and topological analysis, we conclude that twin nucleation occurs through a pure-shuffle mechanism that requires prismatic-basal transformations. Also, we verified a crystal geometry dependent twin growth mechanism, that is the early-stage growth associated with instability of plasticity flow, which can be dominated either by slower movement of prismatic-basal boundary steps, or by faster glide-shuffle along the twinning plane. The fundamental understanding of twinning provides a pathway to understand deformation from a scientific standpoint and the microstructure design principles to engineer metals with enhanced behavior from a technological standpoint.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Atomistic modeling of interface strengthening in Al-Si eutectic alloys

Al-Si cast alloys are usually composed of α-Al and Al-Si eutectic. Si flakes and Al matrix generally hold cube-on-cube orientation relationship with the primary interface (111) Al ∥(111) Si . Extensive experimental studies demonstrated that Si flakes cannot significantly improve mechanical properties of Al-Si cast alloys. We hypothesize that the weak strengthening effect associated with Si flakes might be attributed to thermomechanical properties of Al-Si interfaces besides their morphologies. To characterize Al-Si interfaces with a large lattice mismatch (> 30%), we proposed the quasi-coincident site lattice (Q-CSL) as reference lattice, and demonstrated that the Q-CSL Al-Si coherent interface has three characteristic coherent structures, one stable and low energy structure and two metastable and high energy structures. The translation vectors for the same type of coherent Q-CSL structures are consistent with three displacement shift complete (DSC) vectors. The two metastable structures can be obtained by shifting the low energy structure with three partial DSC vectors. Semi-coherent interface is composed of the low energy Q-CSL patches and three sets of interface misfit dislocations with Burgers vectors same as the DSC vectors. Atomistic simulations revealed that Al-Si interface exhibits low shear resistance. Ideal shear strength of the Q-CSL coherent interface is 110 MPa and semi-coherent interface is 20 MPa. The low shear resistance is attributed to the glide of interface misfit dislocations. Al-Si interface also exhibits low formation and migration energies of point defects. Owing to low shear strength and low formation and migration energies of point defects, interface sliding or shear readily happen under mechanical loading or during dislocation-interface interactions. Lattice dislocations can cross slip onto or climb along Al-Si interfaces. These reactions decrease the number of accumulated dislocation loops around Si flakes and promote nucleation and emission of lattice dislocations from Al-Si interfaces to matrix, consequently reduce the repulsive force on approaching dislocations and weaken Si flakes strengthening effect. In situ tension and compression tests in a scanning electron microscope reveal relatively weak strengthening effect due to Si flakes, consistent with the computed dislocation interaction with interfaces and shear behavior of interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2021

First-principles calculations for understanding microstructures and mechanical properties of co-sputtered Al alloys

Recent experimental studies show that co-sputtering solutes with Al, together, can refine columnar grain size around few tens of nanometers and promote the formation and enhance the stability of planar defects such as stacking faults (SFs) and grain boundaries (GBs) in Al alloys. These crystal defects and fine columnar grains result in high strength, enhanced strain hardening and thermal stability of Al alloys. Using first-principles density-functional theory (DFT) calculations, we studied the role of eleven solutes in tailoring kinetics and energetics of adatoms and clusters on Al {111} surface, stable and unstable stacking fault energies, and kinetic energy barriers for the migration of defects. The calculations show that most solutes can effectively refine columnar grain size by decreasing the diffusivity of adatoms and surface clusters. These solutes do not necessarily decrease the stacking fault energy of Al alloys, but reduce the formation energy of faulted surface clusters and increase the energy barriers for the recovery of faulted surface clusters. Correspondingly, the formation of SFs is kinetically promoted during sputtering. Furthermore, solutes are segregated into the core of Shockley partial dislocations and play a pinning effect on SFs, SF arrays and twin boundaries, enhancing the thermal stability of these crystal defects. These findings provide insights into the design of high-strength Al alloys for high-temperature applications.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The effects of stress, temperature and facet structure on growth of { 10 1 &#xAF; 2 } twins in Mg: a molecular dynamics and phase field study

The present study focuses on the roles of structure, stress and temperature on the mobility of facets bounding twin domains and on the overall impact on the growth kinetics of { 10 1 &#xAF; 2 } twins in Mg. We first use molecular dynamics simulations (MD) to study the relationship between interface structures, stress, temperature and mobility. As facets can exhibit distinct atomic scale structures, we also quantify the effect of stress relaxation mediated by misfit dislocations on the mobility of the basal-prismatic interface. The information gathered for ten different facets is used to calibrate an anisotropic phase field model predicting the effects of temperature and stress on the kinetics and shape of a growing { 10 1 &#xAF; 2 } 3D twin, by comparison with MD data. The comparative analysis suggests that, as compared to simulations of individual facets, the effective mobility of facets can be significantly different during growth of a 3D twin. This can be attributed to the complex three-dimensional internal stress state of the twin and to coupling in facet motion triggered by facet junctions. As such, by directly fitting both the twin growth kinetics and morphology as predicted by MD for different stresses and temperatures, we can identify a limited set of rate-limiting facets that control twin growth and morphology, and measure their effective mobility.

36 MATERIALS SCIENCE↗