Engineering topics

Gonzalez, Carlos

Publications and source records attributed to Gonzalez, Carlos.

4 records

DOE OSTI2020

Adapting Optimal Velocity Tracking Control to Account for WEC Constraints and Power-Take-Off Efficiencies: Preprint

Wave energy converters (WECs) come in many different forms, from point absorbers, oscillating water columns, to bulge wave devices. This paper focuses on the control of point absorber WECs, which typically have a narrow-banded frequency response and, therefore, control is well placed to improve the energy capture of such WECs. The acausal nature of the control problem means that theoretically optimal control is almost impossible to achieve inpractice; however optimal velocity tracking (OVT) offers a simple and robust approximation to optimal control that can achieve better power capture than passive linear damping methods, albeit with necessarily higher force demands. OVT is a form of impedance matching and the magnitude of the power-take off (PTO) force demand is often not linearly proportional to the WEC velocity, which can lead to PTO force and speed combinations far from the optimalPTO efficiency. The highly non-linear PTO force and speed to efficiency mapping can, without remedial measures, severely diminish the effectiveness of OVT techniques. In this paper, limits to the movement and force of the PTO are demonstrated, allowing OVT to be more easily applied in practice. The effect of PTO efficiency is explored, and a potential solution to the problem of adapting control to account for efficiency is presented. Both aspects of the work presented highlight the requirement for co-design of the WEC, PTO, and controller.

conversion efficiency↗

NASA NTRS2018

Modeling Fiber Kinking at the Microscale and Mesoscale

A computational micromechanics (CMM) model is employed to interrogate the assumptions of a recently developed mesoscale continuum damage mechanics (CDM) model for fiber kinking. The CMM model considers an individually discretized three dimensional fiber and surrounding matrix accounting for nonlinearity in the fiber, matrix plasticity, fiber/matrix interface debonding, and geometric nonlinearity. Key parameters of the CMM model were measured through experiments. In particular, a novel experimental technique to characterize the in situ longitudinal compressive strength of carbon fibers through indentation of micropillars is presented. The CDM model is formulated on the basis of Budiansky's fiber kinking theory (FKT) with a constitutive deformation-decomposition approach to alleviate mesh size sensitivity. In contrast to conventional mesoscale CDM models that prescribe a constitutive response directly, the response of the proposed model is an outcome of material nonlinearity and large rotations of the fiber direction following FKT. Comparison of the predictions from the CMM and CDM models shows remarkable correlation in strength, post-peak residual stress, and fiber rotation, with less than 10% difference between the two models in most cases. Additional comparisons are made with several fiber kinking models proposed in the literature to highlight the efficacy of the two models. Finally, the CMM model is exercised in parametric studies to explore opportunities to improve the longitudinal compression strength of a ply through the use of nonconventional microstructures.

Herraez, Miguel↗

NASA NTRS2018

Development of a Mesoscale Finite Element Constitutive Model for Fiber Kinking

A mesoscale finite element material model is proposed to analyze structures that fail by the fiber kinking damage mode. To evaluate the assumptions of the mesoscale model, the results were compared with those of a high-fidelity micromechanical model. A direct comparison between the two models shows remarkable correlation, indicating that the key features of the fiber kinking phenomenon are appropriately accounted for in the mesoscale model. The mesoscale model is applied to structural analysis cases to demonstrate the capabilities of the model. A verification study is conducted with an unnotched compression specimen and preliminary validation is demonstrated with a notched compression specimen. The results show that the model is successful at representing the kinematics of fiber kinking while at the same time highlighting the need for further verification and validation.

Bergan, Andrew C.↗

NASA NTRS2017

Multiscale Fiber Kinking: Computational Micromechanics and a Mesoscale Continuum Damage Mechanics Models

In this work, the fiber kinking phenomenon, which is known as the failure mechanism that takes place when a fiber reinforced polymer is loaded under longitudinal compression, is studied. A computational micromechanics model is employed to interrogate the assumptions of a recently developed mesoscale continuum damage mechanics (CDM) model for fiber kinking based on the deformation gradient decomposition (DGD) and the LaRC04 failure criteria.

Herraez, Miguel↗