Search NASA⌕ Search

Engineering topics

Goodrich, L F

Publications and source records attributed to Goodrich, L F.

Strain and Magnetization Properties of High Subelement Count Tube-Type Nb3Sn Strands

A tubular technique for economical production of Nb{sub 3}Sn material with large numbers of subelements is being explored by Supergenics I LLC and Hyper Tech Research Inc. The number of subelements was increased to 919 (744 subelements plus 175 Cu filaments) by increasing the size at which restacking is carried out. The product exhibited no fabrication problems and was drawn down and tested at a wire diameter of 0.42 mm, where the subelements are 10 {micro}m in diameter. Recently we increased the subelement number to 1387 (1248 subelements plus 139 Cu filaments), which gives a subelement size of 12 {micro}m in 0.7 mm diameter wires. Heat treatment (HT) of different subelement restacks has been investigated, and the best results of critical current and stability are presented. The strain tolerance of the strands with 192 and 744 subelements was also tested, and the strand with fine subelement size showed a high intrinsic irreversible strain limit.

99 GENERAL AND MISCELLANEOUS↗

Development of a Multifilament PIT V3Ga Conductor for Fusion Applications

Previous studies on V{sub 3}Ga assert its suitability for use in proposed fusion reactors. V{sub 3}Ga may outperform Nb{sub 3}Sn in a fusion reactor environment based on its relatively flat critical-current profile in the 15 T-20 T range, resilience to applied strain, and reduced risk of induced radioactivity. A multifilament powder-in-tube V{sub 3}Ga conductor was designed, fabricated and tested with a focus on evaluating critical current versus applied field and applied strain performance, wire drawing difficulties, heat-treatment optimization, and overall feasibility of the concept.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interlaboratory Comparisons of NbTi Critical Current Measurements

We report on a multi-institute comparison of critical current data measured on a modern NbTi wire for the Large Hadron Collider (LHC), which has shown a standard deviation below 1% in critical current density spread in more than 1500 measurements. Interlaboratory comparisons on Nb{sub 3}Sn wires have shown ambiguities that could be attributable to strain related differences in critical current density, originating from differences in sample handling, reaction, and mounting techniques, or also to differences in the magnetic field and current calibrations between the institutes. A round robin test of a well characterized NbTi wire provides a baseline variance in critical current results that is presumed to be attributable only to differences in the characterization systems. Systematic differences on the order of 3.5% are found in the comparison. The most likely cause for the observed differences is a small diameter holder that brings the wire into a strain regime in which strain effects can no longer be ignored. A NbTi round robin test, when performed properly, will separate system differences from sample specific differences and provide laboratories with an opportunity to calibrate equipment against a standard measurement.

43 PARTICLE ACCELERATORS↗

Variable-Temperature Critical-Current Measurements

This is the final report of a three year contract that covered 09/19/2005 to 07/14/2008. We requested and received a no cost time extension for the third year, 07/15/2007 to 07/14/2008, to allow DoE to send us funds if they became available during that year. It turned out that we did not receive any funding for the third year. The following paper covers our variable-temperature critical-current measurements. We made transport critical-current (Ic) measurements on commercial multifilamentary Nb3Sn strands at temperatures (T) from 4 to 17 K and magnetic fields (H) from 0 to 14 T. One of the unique features of our measurements is that we can cover a wide range of critical currents from less than 0.1 A to over 700 A.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗