Engineering topics

Goodwin, Jesse

Publications and source records attributed to Goodwin, Jesse.

5 records

DOE OSTI2024

Digital bead modeling for wire-arc directed energy deposition

Prediction of 2D cross-section and full 3D geometry for stacked weld beads is critical for the outcome of wire-arc directed energy deposition (DED) parts; however, most additive path planning software packages model beads as extrusions of a rectangle. Weld beads are not rectangular, and the resulting shape is dependent upon physics effects at the moment of deposition. Physics phenomena such as the geometry of the underlying surface, the heat input of the welding mode, and the direction of gravity contribute to bead shape. Here, this paper presents a novel implicit modeling method that discretizes a 2D area or 3D volume of space into pixels or voxels and constructs fields based on these physics phenomena. The fields are combined using a weighting scheme trained on 3D scan measurements of welds and wire-arc DED prints. Pixels or voxels are added until the known amount of deposited volume has been achieved. Thereby, a strong conservation of mass principle is applied to the process. Utilizing machine learning techniques, the present model can be trained on a database of scans allowing for the representation of a wide variety of prints. Results show that this method can produce predictions with realistic bead morphology and sub-millimeter form error.

Bead geometry modeling↗

DOE OSTI2024

Positioning Accuracy in a Concurrent Robot-CNC Hybrid Manufacturing System

Abstract Additive manufacturing (AM) has gained notoriety for offering advantages over traditional manufacturing methods, such as increased design complexity and flexibility. However, it has not found widespread use beyond rapid prototyping. One hindrance to the acceptance of AM processes in industry is the time and cost of fabrication per component. While metal AM by itself can be inexpensive, extra manufacturing steps in the form of subtractive manufacturing (SM) may need to be performed to reach final part tolerances, leading to hybrid additive-subtractive manufacturing (HASM) of a part, which increases time and cost. A potential area to reduce cost is through increasing the efficiency of the HASM process by conducting additive and subtractive manufacturing simultaneously. Usually, HASM is performed in a process where AM is completed in one machine or cell and transferred to another machine or cell for SM in a sequential assembly line process. This efficiency decreases part cost, but high aspect ratio parts or parts with internal geometry that require interleaved additive deposition and machining cannot be produced. One unexplored solution to simultaneous HASM that allows for interleaved operations is to operate the deposition head and machining spindle concurrently within the same machine envelope, known as concurrent HASM (CHASM). In this type of process, both AM and SM occur simultaneously on a batch of small parts or a single large part, maintaining a high efficiency without sacrificing the full range of complex geometries that AM allows for. A potential approach to the single-machine method could be to combine a robot and mill within the same envelope. A challenge to this approach, however, is control of both systems. Most machine controllers have limited external communication or, if a robot has been integrated, only offer movement of either the robot or mill at any given time. As a result, systems must pause either the AM or SM process to switch between them rather than working simultaneously. The present work investigates the positional accuracy of such a CHASM system comprised of a robotic arm and a 3-axis mill. Open-loop tests with limited communication between machines are performed on the system to verify positional error during concurrent robot-mill movements. Under certain conditions, it is demonstrated that position error can stay within 2 mm for the duration of a single layer; however, these tests show that, generally, the open-loop positioning performance of the system is inadequate for CHASM without part-specific hand-tuning of parameters. Based on these results, a set of requirements for successful robot-CNC CHASM is proposed for future integrations.

Goodwin, Jesse↗

DOE OSTI2024

Impact of Heat Input and Step Over Distance on Part Geometry for Multi-Bead WAAM Components

Abstract This study investigates the impact of heat input and overlap ratio or stepover distance on part geometry in wire arc additive manufacturing (WAAM). In this work, an experimental approach was taken to quantify the variation in height and aspect ratio of walls at different combinations of overlap and heat input. Multi-bead walls were deposited with the overlap ratio varying from ½, ⅔, and 1 at a low, medium, and high-power set point on the welding power supply. A relationship between heat input, overlap ratio, and the resultant part geometry is established. Trials with an overlap ratio of one and low to medium heat input exhibited greater lack of fusion defects than the high heat input trials. At higher heat input levels, the as-deposited geometry was found to have less variation in height and an increase in aspect ratio compared to lower heat input trials. The aspect ratio of deposited walls ranged from approximately 1, for the low-power trial with an overlap ratio of ½, to approximately 7, for the high-power trial with an overlap ratio of 1. Additionally, the low and medium power trials with an overlap ratio of ⅔ exhibited the least height variation in the top surface for those heat input levels with an average range of 2.9 mm and 1.8 mm respectively. For the high heat input trials, an overlap ratio of 1 was observed to have the least variation in height with a standard deviation of 0.42 mm and an average range of 1.7 mm; however, lack of fusion defects were present in the top surface and the part cross section.

Hussein, Zaky↗

DOE OSTI2023

Vision-based localization for cooperative robot-CNC hybrid manufacturing

Wire and arc additive manufacturing (WAAM) has shown promise in recent years for producing large-scale parts with higher deposition rates than other additive processes. WAAM is often combined with subtractive machining to form a hybrid manufacturing process. This hybrid process can be realized by retrofitting computer numerical control (CNC) machines with deposition heads, adding spindles and deposition heads to robots, or developing part localization methods to transfer parts from an additive cell to a CNC machine. Here, a novel, robot-CNC hybrid configuration is introduced where a maneuverable robot is placed in front of a CNC machine to deposit material within the machine envelop. Furthermore, this method removes the need for part localization and the extensive machine modifications required for retrofitting; however, the problem of robot localization is also added. In this work, the effects of error in vision-based, contactless robot localization on machining parameters in a robot-machine hybrid process were studied. Performance was characterized on an implementation of this system using classical computer vision techniques. In addition, machining simulations were conducted to evaluate the effects of image-induced error on chip thickness, material removal rate, and machining allowance. Initial tests show that computer vision could adequately locate a robot for the hybrid WAAM process within .5 mm.

Hybrid manufacturing↗

DOE OSTI2021

Creation of a prototype biomimetic fish to better understand impact trauma caused by hydropower turbine blade strikes

Biomimetic model organisms could be useful surrogates for live animals in many applications if the models have sufficient biofidelity. One such application is for use in field and laboratory tests of fish mortality associated with passage through hydropower turbines. Laboratory trials suggest that blade strikes are especially injurious and often causes mortality when fish are struck by thinner blades moving at higher velocities. Dose-response relationships have been created from these data, but the exact relationship between fish mortality and the actual forces enacted on fish during simulated blade strike testing remains unknown. Here, we describe the methods used to create a prototype biomimetic model fish composed of ballistic gelatin and covered with a surrogate skin to better approximate the biomechanical properties of a fish body. Frozen fish were scanned with high-fidelity laser scanners, and a 3D-printed, reusable mold was created from which to cast our gelatin model. Computed tomography scan data, imaged directly or taken from online data repositories, were also successfully used to create CAD models for use in additive manufacturing of molds. One 3-axis accelerometer was embedded into the gelatin to compare accelerometer data to dose-response data from previous laboratory research on live fish. The resulting model ( i.e. , Gelfish) had a statistically indistinguishable tissue durometer to that of real fish tissue and preliminary blade strike impact testing suggested its overall flexibility was similar to that of live fish. Gelfish was designed with biofidelity as its guiding principle and our results suggest initial experimentation was successful. Future research will include replication of initial Gelfish test results, quantitative measurement of model flexibility relative to real fish, and inclusion of surrogate skeletal structures to enhance biofidelity. Use of more sophisticated sensors would also better quantify the physical forces of blade strike impact and help determine how said forces correlate with rates of mortality observed during tests on live fish.

36 MATERIALS SCIENCE↗