Search NASA⌕ Search

Engineering topics

Goodyer, M. J.

Publications and source records attributed to Goodyer, M. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

The simulation of a propulsive jet and force measurement using a magnetically suspended wind tunnel model

Models featuring the simulation of exhaust jets were developed for magnetic levitation in a wind tunnel. The exhaust gas was stored internally producing a discharge of sufficient duration to allow nominal steady state to be reached. The gas was stored in the form of compressed gas or a solid rocket propellant. Testing was performed with the levitated models although deficiencies prevented the detection of jet-induced aerodynamic effects. Difficulties with data reduction led to the development of a new force calibration technique, used in conjunction with an exhaust simulator and also in separate high incidence aerodynamic tests.

Garbutt, K. S.↗
NASA NTRS1992

Adaptive wall technology for three-dimensional models at high subsonic speeds and aerofoil testing through the speed of sound

Adaptive wall research at the University of Southampton has been directed towards the development of testing techniques for use in nonporous test sections where two flexible walls are profiled in single curvature. This paper highlights the recent advances that have been made in the testing of 2D airfoils through the speed of sound and the testing of 3D models at high subsonic speeds. Techniques have been developed to accommodate the variety of flow regimes encountered in near sonic airfoil tests. The experimental evidence to date suggests that the new techniques coupled with established procedures allow airfoil data, free from top and bottom wall interference, to be gathered from adaptive flexible walled test sections throughout the entire subsonic, transonic and supersonic speed ranges. Techniques applicable to the testing of 3D models have evolved primarily from experience gained by testing sidewall mounted half-wings. Emphasis has been placed upon models with planforms similar to those of current transport wings. Techniques for high subsonic speeds have now been developed to the point where the residual levels of interference are low.

Lewis, M. C.↗
NASA NTRS1988

Surface flow visualization in the cryogenic wind tunnel

The prospects are reviewed of a range of possible surface flow visualization methods for application to model testing in the large cryogenic wind tunnel. Desirable features are outlined, including the flow details which should be revealed by the various methods. The risks of model and tunnel contamination are discussed, also the coverage of the model surface to be expected, the advance planning and complexity of model design and tunnel equipment required by the visualization method, and the prospects of generating multiple flow images during one tunnel run. The techniques range from the untried to several on which already there is some experience in the cryogenic environment. Directions for further development are suggested.

Goodyer, M. J.↗
NASA NTRS1988

Preliminary experiments on surface flow visualization in the cryogenic wind tunnel by use of condensing or freezing gases

Cryogenic wind tunnel users must have available surface flow visualization techniques to satisfy a variety of needs. While the ideal from an aerodynamic stand would be non-intrusive, until an economical technique is developed there will be occasions when the user will be prepared to resort to an intrusive method. One such method is proposed, followed by preliminary evaluation experiments carried out in environments representative of the cryogenic nitrogen tunnel. The technique uses substances which are gases at normal temperature and pressure but liquid or solid at cryogenic temperatures. These are deposited on the model in localized regions, the patterns of the deposits and their subsequent melting or evaporation revealing details of the surface flow. The gases were chosen because of the likelihood that they will not permanently contaminate the model or tunnel. Twenty-four gases were identified as possibly suitable and four of these were tested from which it was concluded that surface flow direction can be shown by the method. Other flow details might also be detectable. The cryogenic wind tunnel used was insulated on the outside and did not show signs of contamination.

Goodyer, M. J.↗
NASA NTRS1988

Adaptive wall research with two- and three-dimensional models in low speed and transonic tunnels

This paper summarises recent research at the University of Southampton into adaptive wall technology and outlines the direction of current efforts. The work is aimed at developing techniques for use in test sections where the top and bottom walls may be adjusted in single curvature. Wall streamlining eliminates, as far as experimentally possible, the top and bottom wall interference in low speed and transonic aerofoil testing. A streamlining technique has been developed for low speeds which allows the testing of swept wing panels in low interference environments. At higher speeds, a comparison of several two-dimensional transonic streamlining algorithms has been made and a technique for streamlining with a choked test section has also been developed. Three-dimensional work has mainly concentrated on tests of sidewall mounted half-wings and the development of the software packages required to assess interference and to adjust the flexible walls. It has been demonstrated that two-dimensional wall adaptation can significantly modify the level of wall interference around relatively large three-dimensional models. The residual interferences are small and are probably amenable to standard post-test correction methods. Tests on a calibrated wing-body model are planned in the near future to further validate the proposed streamlining technique.

Lewis, M. C.↗
NASA NTRS1987

A swept wing panel in a low speed flexible walled test section

The testing of two-dimensional airfoil sections in adaptive wall tunnels is relatively widespread and has become routine at all speeds up to transonic. In contrast, the experience with the three-dimensional testing of swept panels in adaptive wall test sections is very limited, except for some activity in the 1940's at NPL, London. The current interest in testing swept wing panels led to the work covered by this report, which describes the design of an adaptive-wall swept-wing test section for a low speed wind tunnel and gives test results for a wing panel swept at 40 deg. The test section has rigid flat sidewalls supporting the panel, and features flexible top and bottom wall with ribs swept at the same angle as the wing. When streamlined, the walls form waves swept at the same angle as the wing. The C sub L (-) curve for the swept wing, determined from its pressure distributions taken with the walls streamlined, compare well with reference data which was taken on the same model, unswept, in a test section deep enough to avoid wall interference.

Goodyer, M. J.↗
NASA NTRS1985

Derivation of jack movement influence coefficients as a basis for selecting wall contours giving reduced levels of interference in flexible walled test sections

This report covers work done in a transonic wind tunnel towards providing data on the influence of the movement of wall-control jacks on the Mach number perturbations along the test section. The data is derived using an existing streamline-curvature program, and in application is reduced to matrices of influence coefficients.

Goodyer, M. J.↗
NASA NTRS1985

Introduction to cryogenic wind tunnels

The background to the evolution of the cryogenic wind tunnel is outlined, with particular reference to the late 60's/early 70's when efforts were begun to re-equip with larger wind tunnels. The problems of providing full scale Reynolds numbers in transonic testing were proving particularly intractible, when the notion of satisfying the needs with the cryogenic tunnel was proposed, and then adopted. The principles and advantages of the cryogenic tunnel are outlined, along with guidance on the coolant needs when this is liquid nitrogen, and with a note on energy recovery. Operational features of the tunnels are introduced with reference to a small low speed tunnel. Finally the outstanding contributions are highlighted of the 0.3-Meter Transonic Cryogenic Tunnel (TCT) at NASA Langley Research Center, and its personnel, to the furtherance of knowledge and confidence in the concept.

Goodyer, M. J.↗
NASA NTRS1985

A preliminary investigation of the dynamic force-calibration of a magnetic suspension and balance system

The aerodynamic forces and moments acting upon a magnetically suspended wind tunnel model are derived from calibrations of suspension electro magnet currents against known forces. As an alternative to the conventional calibration method of applying steady forces to the model, early experiences with dynamic calibration are outlined, that is a calibration obtained by oscillating a model in suspension and deriving a force/current relationship from its inertia force and the unsteady components of currents. Advantages of dynamic calibration are speed and simplicity. The two methods of calibration applied to one force component show good agreement.

Goodyer, M. J.↗
NASA NTRS1984

Superconducting electromagnets for large wind tunnel magnetic suspension and balance systems

A superconducting electromagnetic suspension and balance system for an 8 x 8-ft, Mach 0.9 wind tunnel is presented. The system uses a superconducting solenoid as a model core 70 cm long and with a 11.5 cm OD, and a combination of permanent magnet material in the model wings to produce the required roll torque. The design, which uses an integral cold structure rather than separate cryostats for mounting all control magnets, has 14 external magnets, including 4 racetrack-shaped roll coils. Helium capacity of the system is 3.0 to 3.5 l with idling boiloff rate predicted at 0.147 to 0.2 l/h. The improvements yielded a 50-percent reduction in the system size, weight, and cost.

Boom, R. W.↗
NASA NTRS1984

Engineering changes to the 0.1m cryogenic wind tunnel at Southampton University

The more important changes to the 0.1 m cryogenic wind tunnel since its completion in 1977 are outlined. These include detailed improvements in the fan drive to allow higher speeds, and the provision of a test section leg suitable for use with a magnetic suspension and balance system. The instrumentation, data logging, data reduction and tunnel controls were also improved and modernized. A tunnel performance summary is given.

Goodyer, M. J.↗
NASA NTRS1984

Computation of imaginary-side pressure distributions over the flexible walls of the test section insert for the 0.3-M transonic cryogenic tunnel

Two dimensional airfoil testing in an adaptive wall test-section wind tunnel requires the computation of the imaginary flow fields extending outward from the top and bottom test section walls. A computer program was developed to compute the flow field which would be associated with an arbitrary test section wall shape. The program is based on incompressible flow theory with a Prandtl-Glauert compressibility correction. The program was validated by comparing the streamline and the pressure field generated by a source in uniform flow with the results from the computer program. A listing of the program, the validation test results, and a sample program are included.

Goodyer, M. J.↗
NASA NTRS1984

A flying superconducting magnet and cryostat for magnetic suspension of wind-tunnel models

The engineering practicality of a persistent high-field superconducting solenoid cryostat as a magnetic suspension and balance system (MSBS) for wind-tunnel testing of aircraft and missile models is examined. The test apparatus is a simple solenoid of filamentary NbTi superconductor with a cupronickel matrix. The apparatus, with a length-to-diameter ratio of 6 to 1 and a radius of 32 mm, used a 0.25 mm wire with a critical current of 27 A in an external field of 6 T. The total heat inleak of 150 mW was achieved. Helium boiloff rates were tested over a range of operating conditions, including pitch attitudes from 10 deg nose down to 90 deg nose up; the rate was estimated as low, but the aerodynamic acceptability of venting gaseous helium has not been determined. It is shown that the effectiveness of the concept increases with increasing scale, and performance in excess of that of conventional ferromagnets is achievable with reduction in size and costs, and with aptness to transonic wind-tunnel testing. Detailed specifications and schematics are included.

Britcher, C.↗
NASA NTRS1984

Two- and three-dimensional model and wall data from a flexible-walled transonic test section

Both two- and three-dimensional model testing is being carried out in the transonic flexible-walled wind tunnel test section. The test section has flexible top and bottom walls with rigid sidewalls. Interference is eliminated by adjustments based on data taken at walls in two dimensional models. Cast-7 data will illustrate agreement between various flexible-walled tunnels. In three-dimensional models interference cannot be eliminated but wall adjustments can control and relieve the principal sources of wall-induced errors. Estimates of magnitudes of the control which may be exercised on flow by movement of one wall jack are presented. A wall control algorithm (still in analytic development stage) based on use of this data is described. Brief examples of control of wall-induced perturbations in region of model are given.

Goodyer, M. J.↗
NASA NTRS1983

Performance measurements of a pilot superconducting solenoid model core for a wind tunnel magnetic suspension and balance system

The results of experimental demonstrations of a superconducting solenoid model core in the Southampton University Magnetic Suspension and Balance System are detailed. Technology and techniques relevant to large-scale wind tunnel MSBSs comprise the long term goals. The magnetic moment of solenoids, difficulties peculiar to superconducting solenoid cores, lift force and pitching moment, dynamic lift calibration, and helium boil-off measurements are discussed.

Goodyer, M. J.↗
NASA NTRS1982

Extraction of model performance from wall data in a 2-dimensional transonic flexible walled test section

Data obtained from the boundary of a test section provides information on the model contained within it. A method for extracting some of this data in two dimensional testing is described. Examples of model data are included on lift, pitching moment and wake displacement thickness. A FORTRAN listing is also described, having a form suitable for incorporation into the software package used in the running of such a test section.

Goodyer, M. J.↗
NASA NTRS1982

The status of two- and three-dimensional testing in the University of Southampton transonic self-streamlining wind tunnel

An automated test section was used to develop a flexible walled testing technique which eliminates some sources of uncertainty in boundary interference effects which exist in conventional transonic test sections. The flexible floor and ceiling of the test section were adjusted to contours which produce a constant Mach number distribution along each wall with no model present. These aerodynamically straight contours form the basis for all streamlining. The wall data are to contain information on the models performance and on lift. Two dimensional validation testing has continued with a cambered NPL 9510 section. Lift data up to Mach 0.87 are compared with reference data. Drag information on a NACA 0012-64 section is presented to indicate the powerful effects of streamlining. Preliminary three dimensional testing in the two dimensional test section has demonstrated that model and support blockage can be relieved by wall contouring.

Wolf, S. W. D.↗