Engineering topics

Goree, J. G.

Publications and source records attributed to Goree, J. G..

At least 19 records

NASA NTRS1990

Effect of interleaves on fracture of laminated composites. I - Analysis. II - Solution and results

The effect of interleaves placed between the fiber-reinforced plies of multilayered composite laminates is investigated analytically, with the composite approximated by linearly elastic isotropic media consisting of half-planes separated from a finite-width layer by thin interleaves of low extensional and shear moduli. Integral equations are derived which describe the effect of interleaves on damage growth. Numerical solutions are then developed which are based on Gaussian integration techniques and Hadamard's concept of differentiation of Cauchy integrals. Critical stresses and displacements are calculated to investigate the influence of relative elastic properties and geometry of the interleafed composite on interface debonding, extent and suppression and delamination, and stress relieving in the undamaged plies.

Kaw, A. K.↗

NASA NTRS1989

Fracture of silicon carbide whisker reinforced aluminum

An attempt is made to apply standard fracture toughness testing procedures, developed for metals, to whisker reinforced metal matrix composites. Test were carried out on compact-tension, center-notched, and edge-notched specimens of silicon carbide whisker reinforced extruded 2124 aluminum plate (10 and twenty volume percent of whiskers), with the loading direction either parallel or perpendicular to the extrusion direction. None of the tests is found to give a valid fracture toughness according to the criteria of the ASTM Standard E-399.

Albritton, J. R.↗

NASA NTRS1988

Fracture criteria for discontinuously reinforced metal matrix composites

Summarized is the progress achieved during the period September 16, 1987 to August 15, l988 on NASA Grant NAG1-724, Fracture Criteria for Discontinuously Reinforced Metal Matrix Composites. Appended are copies of three manuscripts prepared under NASA funding during the performance period.

Rack, H. J.↗

NASA NTRS1988

Fracture criteria for discontinuously reinforced metal matrix composites

The effect of sample configuration on the details of initial crack propagation in discontinuously whisker reinforced aluminum metal matrix composites was investigated. Care was taken to allow direct comparison of fracture toughness values utilizing differing sample configurations and orientations, holding all materials variables constant, e.g., extrusion ration, heat treatment, and chemistry.

Rack, H. J.↗

NASA NTRS1985

The accuracy of approximate solutions in the analysis of fracture of composites

This paper concerns the accuracy of three related mathematical models (developed by Hedgepeth, Eringen and Sendeckyj and Jones) used in the stress analysis and in fracture studies of continuous-fiber composites. These models have particular application in the investigation of fiber and matrix stresses in unidirectional composites in the region near a crack tip. The interest in such models is motivated by the desire to be able to simplify the equations of elasticity to the point that they can be solved in a relatively easy manner.

Goree, J. G.↗

NASA NTRS1985

Longitudinal splitting in unidirectional composites, analysis and experiments

An experimental study is conducted to determine the fracture behavior of center notched, unidirectional graphite/epoxy laminates when subjected to tensile loading. The actual behavior is compared to the behavior predicted by a mathematical model based on classical shear-lag assumptions. The model allows for damage to occur in the form of longitudinal matrix yielding and splitting with the matrix assumed to fail in pure shear. Results indicate that the model is capable of predicting split initiation stress levels accurately, but does not describe the subsequent split growth adequately. The model predicts rapid split growth following split initiation due to shear failure, while the actual behavior involves a slow split growth region prior to the rapid growth region. It is suggested that transverse matrix normal stresses are responsible for split initiation and the early, slow split growth. The model predicts the actual initiation stress levels reliably, and also appears to be able to predict the point at which the shear failure mode begins to dominate. The shear failure mode does eventually dominate, but at a slower rate than predicted. The nonuniform structure of the graphite/epoxy laminates is thought to be responsible for decreasing the split growth rate due to shear failure.

Goree, J. G.↗

NASA NTRS1985

A comparison of finite-difference and finite-element methods for calculating free edge stresses in composites

It is pointed out that edge delamination is a serious failure mechanism for laminated composite materials. Various numerical methods have been utilized in attempts to calculate the interlaminar stress components which precede delamination in a laminate. There are, however, discrepancies regarding the results provided by different methods, taking into account a finite-difference procedure, a perturbation procedure, and finite element approaches. The present investigation has the objective to assess the capacity of a finite difference method to predict the character and magnitude of the interlaminar stress distributions near an interface corner. A second purpose of the investigation is to determine if predictions by finite element method in-plane, interlaminar stress components near an interface corner represent actual laminate behavior.

Bauld, N. R., Jr.↗

NASA NTRS1985

Shear-lag analysis of notched laminates with interlaminar debonding

The fracture behavior of a debonded zone of finite width with no longitudinal damage in the unidirectional ply is predicted and the solution is then extended to include longitudinal matrix yielding and splitting in the unidirectional ply at the crack tip. The shear-lag assumption is used to describe the shear transfer between fibers. The fracture behavior of the laminate is studied as a function of initial crack length, constraint ratio, and width of the debonded zone. Results indicate that debonding can reduce the maximum fiber stress at the crack tip on the order of ten percent. This effect is maximum for a debonded width of two or three fiber spacings and is independent of the initial crack length. As the debond width grows beyond this point, the maximum stress increases. For widths of about ten fiber spacings or more, the maximum fiber stress is larger than for the fully bonded case. In the presence of longitudinal matrix damage the same general behavior is found; however, the location of the maximum fiber stress is quite complex.

Kaw, A. K.↗

NASA NTRS1985

The accuracy of approximate solutions in the analysis of fracture of composites

Goree, J. G.↗

NASA NTRS1984

Opening of an interface flaw in a layered elastic half-plane under compressive loading

A static analysis is given of the problem of an elastic layer perfectly bonded, except for a frictionless interface crack, to a dissimilar elastic half-plane. The free surface of the layer is loaded by a finite pressure distribution directly over the crack. The problem is formulated using the two dimensional linear elasticity equations. Using Fourier transforms, the governing equations are converted to a pair of coupled singular integral equations. The integral equations are reduced to a set of simultaneous algebraic equations by expanding the unknown functions in a series of Jacobi polynomials and then evaluating the singular Cauchy-type integrals. The resulting equations are found to be ill-conditioned and, consequently, are solved in the least-squares sense. Results from the analysis show that, under a normal pressure distribution on the free surface of the layer and depending on the combination of geometric and material parameters, the ends of the crack can open. The resulting stresses at the crack-tips are singular, implying that crack growth is possible. The extent of the opening and the crack-top stress intensity factors depend on the width of the pressure distribution zone, the layer thickness, and the relative material properties of the layer and half-plane.

Kennedy, J. M.↗

NASA NTRS1984

Shear-lag analysis of notched laminates with interlaminar debonding

The fracture behavior of a debonded zone of finite width with no longitudinal damage in the unidirectional ply is predicted and the solution is then extended to include longitudinal matrix yielding and splitting in the unidirectional ply at the crack tip. The shear-lag assumption is used to describe the shear transfer between fibers. The fracture behavior of the laminate is studied as a function of initial crack length, constraint ratio, and width of the debonded zone. Results indicate that debonding can reduce the maximum fiber stress at the crack tip on the order of ten percent. This effect is maximum for a debond width of two or three fiber spacings and is independent of the initial crack length. As the debond width grows beyond this point, the maximum stress increases. For widths of about ten fiber spacings or more, the maximum fiber stress is larger than for the fully bonded case. In the presence of longitudinal matrix damage the same general behavior is found; however, the location of the maximum fiber stress is quite complex.

Goree, J. G.↗

NASA NTRS1984

Analysis of a unidirectional, symmetric buffer strip laminate with damage

A method for predicting the fracture behavior of hybrid buffer strip laminates is presented in which the classical shear-lag model is used to represent the shear stress distribution between adjacent fibers. The method is demonstrated by applying it to a notched graphite/epoxy laminate, and the results show clearly the manner in which the most efficient combination of buffer strip properties can be selected in order to arrest the crack. The ultimate failure stress of the laminate is plotted vs the buffer strip width. It is shown that in the case of graphite-epoxy and S-glass epoxy laminates, the optimum buffer strip spacing to width ratio should be about four to one.

Dharani, L. R.↗

NASA NTRS1983

Fracture behavior of unidirectional boron/aluminum composite laminates

An experiment was conducted to verify the results of mathematical models which predict the stresses and displacements of fibers and the amount of damage growth in a center-notched lamina as a function of the applied remote stress and the matrix and fiber material properties. A brittle lacquer coating was used to detect the yielding in the matrix while X-ray techniques were used to determine the number of broken fibers in the laminate. The notched strengths and the amounts of damage found in the specimens agree well with those predicted by the mathematical model. It is shown that the amount of damage and the crack opening displacement does not depend strongly on the number of plies in the laminate for a given notch width. By heat-treating certain laminates to increase the yield stress of the alumina matrix, the effect of different matrix properties on the fracture behavior was investigated. The stronger matrix is shown to weaken the notched laminate by decreasing the amount of matrix damage, thereby making the laminate more notch sensitive.

Goree, J. G.↗

NASA NTRS1983

An investigation of the accuracy of finite difference methods in the solution of linear elasticity problems

The accuracy of the finite difference method in the solution of linear elasticity problems that involve either a stress discontinuity or a stress singularity is considered. Solutions to three elasticity problems are discussed in detail: a semi-infinite plane subjected to a uniform load over a portion of its boundary; a bimetallic plate under uniform tensile stress; and a long, midplane symmetric, fiber reinforced laminate subjected to uniform axial strain. Finite difference solutions to the three problems are compared with finite element solutions to corresponding problems. For the first problem a comparison with the exact solution is also made. The finite difference formulations for the three problems are based on second order finite difference formulas that provide for variable spacings in two perpendicular directions. Forward and backward difference formulas are used near boundaries where their use eliminates the need for fictitious grid points.

Bauld, N. R., Jr.↗

NASA NTRS1983

Shear-lag analysis of a hybrid, unidirectional composite with fiber damage

Development of a method of analysis capable of predicting accurately the fracture behavior of unidirectional hybrid (buffer strip) composite laminates was studied. Three particular solutions are discussed in detail: broken fibers in a unidirectional half-plane; adjoined half planes of different fiber and matrix properties; and the solution of two half planes bounding a third distinct region of finite width. This finite width region represents a buffer strip and primary attention is given to the potential of this strip to arrest a crack that originates in one of the half planes. A materials modeling approach using the classical shear lag assumption to describe the stress transfer between fibers was analyzed. Explicit fiber and matrix properties of the three regions are retained, and changes in the laminate behavior as a function of the relative material properties, buffer strip width, and initial crack length are discussed.

Goree, J. G.↗

NASA NTRS1983

Analysis of a hybrid-undirectional buffer strip laminate

A method of analysis capable of predicting accurately the fracture behavior of a unidirectional composite laminate containing symmetrically placed buffer strips is presented. As an example, for a damaged graphite/epoxy laminate, the results demonstrate the manner in which to select the most efficient combination of buffer strip properties necessary to inhibit crack growth. Ultimate failure of the laminate after the arrest can occur under increasing load either by continued crack extension through the buffer strips or the crack can jump the buffer strips. For some typical hybrid materials it is found that a buffer strip spacing to width ratio of about four to one is the most efficient.

Dharani, L. R.↗

NASA NTRS1983

Mathematical modeling of damage in unidirectional composites

Extending the work of Goree and Gross (1979), solutions are given for a two-dimensional region of unidirectional fibers embedded in an elastic matrix whose initial flaw may take the form of a transverse notch, a rectangular cutout, or a circular hole. Subsequent flaw-induced damage is generated by remote stresses acting parallel to the fibers. For the case of such ductile matrix composites as boron/aluminum, present results indicate that both longitudinal matrix yielding and transverse notch extension must be included in order for the model to agree with experimental results. Little difference is found for the three types of initial damage considered. In all cases, the presence of additional damage changes the nature of stress distribution through the unbroken fibers.

Goree, J. G.↗

NASA NTRS1983

Analysis of a hybrid, unidirectional buffer strip laminate

A method of analysis capable of predicting accurately the fracture behavior of a unidirectional composite laminate containing symmetrically placed buffer strips is presented. As an example, for a damaged graphite/epoxy laminate, the results demonstrate the manner in which to select the most efficient combination of buffer strip properties necessary to inhibit crack growth. Ultimate failure of the laminate after crack arrest can occur under increasing load either by continued crack extension through the buffer strips or the crack can jump the buffer strips. For some typical hybrid materials it is found that a buffer strip spacing-to-width ratio of about four to one is the most efficient.

Dharani, L. R.↗