Engineering topics

Grace A Belancik

Publications and source records attributed to Grace A Belancik.

6 records

NASA NTRSDate not supplied

Comparison of Alternative Configurations of an Integrated Open-Loop Carbon Dioxide Removal System using Liquid Amine

Several carbon dioxide removal systems are being investigated for applications in microgravity. The liquid amine wedge system utilizes the capillary action of liquids to prevent the mixing of the air and liquid while still allowing for carbon dioxide capture at their interface. A one crew mission requires approximately 1 kg per day of carbon dioxide removal to prevent adverse health effects. A proposed design of a wedge tray system can be improved from the initial testing parameters to achieve the required carbon dioxide capture for one crew. The wedge trays in the contactor can be organized in either a parallel configuration to accumulate less CO2 in the liquid but at a higher flow rate or a series configuration to yield a higher weight percentage of CO2 in the liquid but at a lower flow rate. The gas flow rate and composition were held constant at 26scfm and 2600ppm, respectively, due to constraints of other proposed systems but the liquid flow rate was adjusted between 0.1mL/min and 10mL/min. The flow rate that yielded the best carbon dioxide capture was X mL/min and Y mL/min for the parallel and series configurations, respectively. The degasser temperature and pressure were varied from 80 to 100°C and 0 and -3 inHg. The largest carbon dioxide flux of Z kg/day/m2 was observed at a contactor liquid flow rate of X mL/min and a degasser temperature and pressure of T°C and P inHg.

Adrian Cortez↗

NASA NTRSDate not supplied

Literature Review of Microwave Regeneration of CO2 Capture Sorbent Materials

Utilizing liquid amines for air revitalization applications has been of continued interest for many decades. They have the advantage of being regenerable sorbents with long lifetimes and a high acuteness for carbon dioxide. While their usage on Earth for flue gas and submarines has been explored for some time now, they are still being researched for use in microgravity environments. To succeed in a microgravity environment, such as usage on the International Space Station, an air revitalization system that is reliant on liquid amines as its sorbent must have a low Equivalent System Mass (ESM), among many other performance parameters. One way of optimizing this ESM number is through bringing down the systems power consumption with the use of microwave heating of the liquid sorbent. Microwave heating allows the liquid sorbent to be heated in a much more efficient way when compared to conventional types of heating techniques, such as convection or conduction. This paper will explore the physical mechanisms behind microwave heating, and how it could potentially be applied to a liquid amine carbon capture system, laying out any concerns and future constraints that a system designer may encounter.

Tiago Faria Costa↗

NASA NTRSDate not supplied

Diglycolamine Material Compatibility through Mechanical Testing

One promising candidate for use as a liquid sorbent in air revitalization technologies is a mixture of diglycolamine and water. This solution can react heavily with certain materials, putting a constraint on what materials can be used when designing and operating a liquid amine air revitalization system. Initial testing on materials has been done in the Air Revitalization labs at NASA Ames Research Center (ARC) through dunk testing of materials and physically checking for swelling, cracking, or any sort of corrosion of the material at hand. While this approach allowed for a quick way of material testing, a more thorough approach is favorable to allow for a database of compatible materials and their properties after contact with the solution for extended periods of time to be compiled. With this database, an air revitalization system intended for long-duration space flight can be designed and operated with confidence that the materials chosen will not degrade and need to be replaced over time.

Tiago Faria Costa↗

NASA NTRSDate not supplied

Comparison of Equivalent System Mass (ESM) and Modeling Results from Improved Heat Loss Approaches for the Carbon Dioxide Deposition (CDep) System

Proper insulation on any type of cryogenic system is essential for its performance to be optimal, as a poorly insulated system will allow for significant heat loss. Different insulation arrangements for CDep were considered, and performance was simulated and measured in Modelica. Heat loss was correlated to cycle time and CO2 deposition efficiency, which led to overall system power usage. Mass, volume, and power consumption were weighted accordingly in the ESM calculations to guide selection of the CDep insulation scheme.

Marian Alcid↗

NASA NTRSDate not supplied

Design Concepts for an Optimized, Modular, and Scalable Liquid Amine Test Stand

The Air Revitalization Labs at NASA Ames Research Center (ARC) is investigating liquid amines to for their performance removing spacecraft carbon dioxide (CO2) for crewed space missions. Development of the current one-crew scale amine test stand stems from several modifications to a test stand initially built at NASA Johnson Space Center (JSC) This sub-scale system has been modified to incorporate a flow spreader for the inlet air stream, an updated contactor design for CO2 capture, a degasser to regenerate the liquid sorbent and recover the captured CO2, and a condenser to reduce water loss. Results from the existing integrated liquid amine test stand have provided valuable insight, but continued performance optimization requires design and build of a new integrated test system. New design concepts will institute a modular configuration to allow for interfacing with novel contactor and degasser architecture, parallel or series flow pathways for the air stream and liquid sorbent, and scaling up to a 4-crew CO2 removal system.

Tiago Faria Costa↗

NASA NTRSDate not supplied

Testing of the ISS’s Charcoal HEPA Integrated Particle Scrubber (CHIPS) Filters to Ascertain an Efficiency Curve and Most Penetrating Particle Size

High air quality is a top priority in hermetically sealed environments, such as the International Space Station (ISS). Aerosol particulate filtration on the ISS is achieved via 21 HEPA filters. Traditional HEPA filters have an efficiency of 99.97%, but HEPA filters aboard the ISS have been found to achieve 99.99% efficiency. This may be due to the flight-grade HEPA filters chosen or, less likely, that they are combined with activated charcoal filters for siloxane removal in a combination referred to as Charcoal HEPA Integrated Particle Scrubbers (CHIPS) filters. All filters have a Most Penetrating Particle Size (MPPS), but, until now, the MPPS and efficiency curve of the CHIPS filters was not known. The efficiency curve of the CHIPS filters was ascertained at NASA Glenn Research Center through standard salt crystal aerosolization. This method was selected over aerosolized oil droplets due to a desire to preserve the filter’s function for further testing. The CHIPS filters were tested as they are oriented on the ISS (activated charcoal filter followed by a flight-grade HEPA filter), with the HEPA portion alone, and with the activated charcoal portion alone. The results of this experiment are generally useful but can be especially useful for the microbiology and Environmental Control and Life Support Systems (ECLSS). This is due to microbial contamination being a potential concern in the air revitalization systems on the ISS. Knowing the MMPS of the CHIPS filters, in conjunction with levels of airborne microbes, is useful for predicting which and how many microbes are likely to get through the HEPA filters that sit in the beginning of the ISS airstream. It may also be useful to other groups at NASA to know how many particulates are able to pass through high-efficiency filtration, and even for healthcare cleanrooms and other air purification pursuits.

A Nicolas Whitlock↗