Engineering topics
Publications and source records attributed to Graves, S. R..
This paper presents viewgraphs on thiokol solid rocket motors. The topics include: 1) Communications; 2) Military and government intelligence; 3) Positioning satellites; 4) Remote sensing; 5) Space burial; 6) Science; 7) Space manufacturing; 8) Advertising; 9) Space rescue space debris management; 10) Space tourism; 11) Space settlements; 12) Hazardous waste disposal; 13) Extraterrestrial resources; 14) Fast package delivery; and 15) Space utilities.
In order to explain the results of the testing conducted in Part I and relate the subscale test specimen performance to case performance during prelaunch loading, a comprehensive analysis program was conducted. Finite element models of both full-scale case and subscale test coupons were made. Validated axisymmetric models were used for the case analyses. Modeling of coupons was accomplished using a generalized plane strain finite element model in most cases, although some three-dimensional finite element modeling was used to investigate the importance of three-dimensional effects on the coupon performance. The large number of plies and complexity of the test coupons used limited the finite element grids to a through-the-thickness discretization of one element per ply. Delaminations observed in the helical ply dropoff region were modeled using frictionless sliders. Comparisons of predicted strains and displacements were made with the test data from both cases and coupons to validate the finite element models. Based on observations of the test results and finite element predictions, a failure criterion for both coupons and cases was postulated and then validated by comparing performance predictions to test results. Finally, the validated failure criterion was used to predict the performance of the first two flight cases under prelaunch loads.
The large stiffness-to-weight and strength-to-weight ratios of graphite composite in combination with the 600 F structural capability of the polyimide matrix can reduce the total structure/TPS weight of reusable space vehicles by 20-30 percent. It is inevitable that with planned usage of GR/PI structural components, damage will occur either in the form of intrinsic flaw growth or mechanical damage. Research and development programs were initiated to develop repair processes and techniques specific to Celion/LARC-160 GR/PI structure with emphasis on highly loaded and lightly loaded compression critical structures for factory type repair. Repair processes include cocure and secondary bonding techniques applied under vacuum plus positive autoclave pressure. Viable repair designs and processes are discussed for flat laminates, honeycomb sandwich panels, and hat-stiffened skin-stringer panels. The repair methodology was verified through structural element compression tests at room temperature and 315 C (600 F).
A structural test program was conducted on a Celion/LARC-160 graphite/polyimide technology demonstration segment (TDS) to verify the technology. The 137 x 152 cm (54 x 60 in.) TDS simulates a full-scale section of the orbiter composite body flap design incorporating three ribs and extending from the forward cove back to the rear spar. The TDS was successfully subjected to mechanical loads and thermal environments (-170 to 316 C) simulating 100 shuttle orbiter missions. Successful completion of the test program verified the design, analysis, and fabrication methodology for bonded Gr/PI honeycomb sandwich structure and demonstration that Gr/PI composite technology readiness is established.
The materials, production processes, testing procedures, and repair techniques for composite structures on the Orbiter are reviewed. The Orbiter currently features graphite/epoxy payload bay doors, as well as graphite/polyimide elevons, vertical tail, and aft body flap, which can withstand up to 600 F temperatures. Graphite/polyimide is also being considered for areas of the baseline aluminum structure and the thermal protection system in order to achieve a 20-30% weight reduction, i.e., over 7.5 tons. An analysis of the allowable stresses on FRC imide thermal protection system tiles bonded directly to the structure has shown satisfactory performances in high temperature and cryogenic conditions, although failure modes are yet to be determined. Ultrasonic emissions have been used for defect detection in nondestructive evaluations, together with tension, notch, shear, and compression tests. Field repairs have not been perfected, and require the evolution of high temperature adhesives that are curable under vacuum pressure and heat blankets.
For future missions, increases in Space Shuttle orbiter deliverable and recoverable payload weight capability may be needed. Such increases could be obtained by reducing the inert weight of the Shuttle. The application of advanced composites in orbiter structural components would make it possible to achieve such reductions. In 1975, NASA selected the orbiter body flap as a demonstration component for the Composite for Advanced Space Transportation Systems (CASTS) program. The progress made in 1977 through 1980 was integrated into a design of a graphite/polyimide (Gr/Pi) body flap technology demonstration segment (TDS). Aspects of composite body flap design and analysis are discussed, taking into account the direct-bond fibrous refractory composite insulation (FRCI) tile on Gr/Pi structure, Gr/Pi body flap weight savings, the body flap design concept, and composite body flap analysis. Details regarding the Gr/Pi technology demonstration segment are also examined.