Engineering topics

Greer, Lawrence C.

Publications and source records attributed to Greer, Lawrence C..

8 records

NASA NTRS2013

Cratos: The Evolution of a Robotic Vehicle

Cratos was originally designed to evaluate a small footprint, low-power, tracked vehicle for traversing a crater face and for scraping regolith from a crater basin on the lunar surface. These activities require a power-to-weight ratio such that the vehicle is able to pull its entire mass vertically off the ground with the power from one track. Further complicating matters, the available power-units that fit the vehicles approximate one cubic meter volume, restrict power consumption to 100 watts. Lastly, the vehicle is required to telemeter data from an array of sensors to a remote control station for further study. This unique mix of design constraints lead to the creation of a versatile mobile sensor platform, described in this paper, capable of performing a myriad of functions beyond the scope of its original purpose.

Greer, Lawrence C.↗

NASA NTRS2011

Teleoperated Marsupial Mobile Sensor Platform Pair for Telepresence Insertion Into Challenging Structures

A platform has been developed for two or more vehicles with one or more residing within the other (a marsupial pair). This configuration consists of a large, versatile robot that is carrying a smaller, more specialized autonomous operating robot(s) and/or mobile repeaters for extended transmission. The larger vehicle, which is equipped with a ramp and/or a robotic arm, is used to operate over a more challenging topography than the smaller one(s) that may have a more limited inspection area to traverse. The intended use of this concept is to facilitate the insertion of a small video camera and sensor platform into a difficult entry area. In a terrestrial application, this may be a bus or a subway car with narrow aisles or steep stairs. The first field-tested configuration is a tracked vehicle bearing a rigid ramp of fixed length and width. A smaller six-wheeled vehicle approximately 10 in. (25 cm) wide by 12 in. (30 cm) long resides at the end of the ramp within the larger vehicle. The ramp extends from the larger vehicle and is tipped up into the air. Using video feedback from a camera atop the larger robot, the operator at a remote location can steer the larger vehicle to the bus door. Once positioned at the door, the operator can switch video feedback to a camera at the end of the ramp to facilitate the mating of the end of the ramp to the top landing at the upper terminus of the steps. The ramp can be lowered by remote control until its end is in contact with the top landing. At the same time, the end of the ramp bearing the smaller vehicle is raised to minimize the angle of the slope the smaller vehicle has to climb, and further gives the operator a better view of the entry to the bus from the smaller vehicle. Control is passed over to the smaller vehicle and, using video feedback from the camera, it is driven up the ramp, turned oblique into the bus, and then sent down the aisle for surveillance. The demonstrated vehicle was used to scale the steps leading to the interior of a bus whose landing is 44 in. (.1.1 m) from the road surface. This vehicle can position the end of its ramp to a surface over 50 in. (.1.3 m) above ground level and can drive over rail heights exceeding 6 in. (.15 cm). Thus configured, this vehicle can conceivably deliver the smaller robot to the end platform of New York City subway cars from between the rails. This innovation is scalable to other formulations for size, mobility, and surveillance functions. Conceivably the larger vehicle can be configured to traverse unstable rubble and debris to transport a smaller search and rescue vehicle as close as possible to the scene of a disaster such as a collapsed building. The smaller vehicle, tethered or otherwise, and capable of penetrating and traversing within the confined spaces in the collapsed structure, can transport imaging and other sensors to look for victims or other targets.

Krasowski, Michael J.↗

NASA NTRS2008

Excavation on the Moon: Regolith Collection for Oxygen Production and Outpost Site Preparation

The development of a robust regolith moving system for lunar and planetary processing and construction is critical to the NASA mission to the Moon and Mars. Oxygen production may require up to 200 metric tons of regolith collection per year; outpost site development may require several times this amount. This paper describes progress in the small vehicle implement development and small excavation system development. Cratos was developed as a platform for the ISRU project to evaluate the performance characteristics of a low center of gravity, small (0.75m x 0.75m x 0.3m), low-power, tracked vehicle performing excavation, load, haul, and dump operations required for lunar ISRU. It was tested on loose sand in a facility capable of producing level and inclined surfaces, and demonstrated the capability to pick up, carry, and dump sand, allowing it to accomplish the delivery of material to a site. Cratos has demonstrated the capability to pick up and deliver simulant to a bury an inflatable habitat, to supply an oxygen production plant, and to build a ramp.

Caruso, John J.↗

NASA NTRS2008

Development and Buildup of a Stirling Radioisotope Generator Electrical Simulator

This paper describes the development of a Stirling Radioisotope Generator (SRG) Simulator for use in a prototype lunar robotic rover. The SRG developed at NASA Glenn Research Center (GRC) is a promising power source for the robotic exploration of the sunless areas of the moon. The simulator designed provides a power output similar to the SRG output of 5.7 A at 28 Vdc, while using ac wall power as the input power source. The designed electrical simulator provides rover developers the physical and electrical constraints of the SRG supporting parallel development of the SRG and rover. Parallel development allows the rover design team to embrace the SRG s unique constraints while development of the SRG is continued to a flight qualified version.

Prokop, Norman F.↗

NASA NTRS2007

Cratos: A Simple Low Power Excavation and Hauling System for Lunar Oxygen Production and General Excavation Tasks

The development of a robust excavating and hauling system for lunar and planetary excavation is critical to the NASA mission to the Moon and Mars. Cratos was developed as a low center of gravity, small (.75m x .75m x 0.3m), low power tracked test vehicle. The vehicle was modified to excavate and haul because it demonstrated good performance capabilities in a laboratory and field testing. Tested on loose sand in the SLOPE facility, the vehicle was able to pick up, carry, and dump sand, allowing it to accomplish the standard requirements delivery of material to a lunar oxygen production site. Cratos can pick up and deliver raw material to a production plant, as well as deliver spent tailings to a disposal site. The vehicle can complete many other In-Situ Resource Utilization (ISRU) excavation chores and in conjunction with another vehicle or with additional attachments may be able to accomplish all needed ISRU tasks.

Caruso, John J.↗

NASA NTRS2005

Forward Technology Solar Cell Experiment (FTSCE) for MISSE-5 Verified and Readied for Flight on STS-114

The Forward Technology Solar Cell Experiment (FTSCE) is a space solar cell experiment built as part of the Fifth Materials on the International Space Station Experiment (MISSE-5): Data Acquisition and Control Hardware and Software. It represents a collaborative effort between the NASA Glenn Research Center, the Naval Research Laboratory, and the U.S. Naval Academy. The purpose of this experiment is to place current and future solar cell technologies on orbit where they will be characterized and validated. This is in response to recent on-orbit and ground test results that raised concerns about the in-space survivability of new solar cell technologies and about current ground test methodology. The various components of the FTSCE are assembled into a passive experiment container--a 2- by 2- by 4-in. folding metal container that will be attached by an astronaut to the outer structure of the International Space Station. Data collected by the FTSCE will be relayed to the ground through a transmitter assembled by the U.S. Naval Academy. Data-acquisition electronics and software were designed to be tolerant of the thermal and radiation effects expected on orbit. The experiment has been verified and readied for flight on STS-114.

Jenkins, Phillip P.↗

NASA NTRS2003

Cooperative Multi-Agent Mobile Sensor Platforms for Jet Engine Inspection: Concept and Implementation

Cooperative behavior algorithms utilizing swarm intelligence are being developed for mobile sensor platforms to inspect jet engines on-wing. Experiments are planned in which several relatively simple autonomous platforms will work together in a coordinated fashion to carry out complex maintenance-type tasks within the constrained working environment modeled on the interior of a turbofan engine. The algorithms will emphasize distribution of the tasks among multiple units; they will be scalable and flexible so that units may be added in the future; and will be designed to operate on an individual unit level to produce the desired global effect. This proof of concept demonstration will validate the algorithms and provide justification for further miniaturization and specialization of the hardware toward the true application of on-wing in situ turbine engine maintenance.

Litt, Jonathan S.↗

NASA NTRS2003

Mobile Sensor Technologies Being Developed

The NASA Glenn Research Center is developing small mobile platforms for sensor placement, as well as methods for communicating between roving platforms and a central command location. The first part of this project is to use commercially available equipment to miniaturize an existing sensor platform. We developed a five-circuit-board suite, with an average board size of 1.5 by 3 cm. Shown in the preceding photograph, this suite provides all motor control, direction finding, and communications capabilities for a 27- by 21- by 40-mm prototype mobile platform. The second part of the project is to provide communications between mobile platforms, and also between multiple platforms and a central command location. This is accomplished with a low-power network labeled "SPAN," Sensor Platform Area Network, a local area network made up of proximity elements. In practice, these proximity elements are composed of fixed- and mobile-sensor-laden science packages that communicate to each other via radiofrequency links. Data in the network will be shared by a central command location that will pass information into and out of the network through its access to a backbone element. The result will be a protocol portable to general purpose microcontrollers satisfying a host of sensor networking tasks. This network will enter the gap somewhere between television remotes and Bluetooth but, unlike 802.15.4, will not specify a physical layer, thus allowing for many data rates over optical, acoustical, radiofrequency, hardwire, or other media. Since the protocol will exist as portable C-code, developers may be able to embed it in a host of microcontrollers from commercial to space grade and, of course, to design it into ASICs. Unlike in 802.15.4, the nodes will relate to each other as peers. A demonstration of this protocol using the two test bed platforms was recently held. Two NASA modified, commercially available, mobile platforms communicated and shared data with each other and a central command location. Web-based control and interrogation of similar mobile sensor platforms have also been demonstrated. Expected applications of this technology include robotic planetary exploration, astronaut-to-equipment communication, and remote aerospace engine inspections.

FROM↗