Search NASA⌕ Search

Engineering topics

Grenier, Antonin

Publications and source records attributed to Grenier, Antonin.

A high-temperature sample changer for parallelized in situ X-ray studies to efficiently explore reaction space

A sample environment for high-throughput X-ray scattering studies in transmission geometry to probe the mechanism and kinetics of moderate-temperature reactions in solution, molten fluxes and solids is described. This high-temperature sample changer enables efficient studies of reactions that are slow relative to the timescale of the X-ray scattering measurements by allowing up to 18 samples to be probed at the same temperature in parallel. This significantly enhances the throughput ofin situX-ray scattering studies as the sample changer effectively facilitates systematic studies that compare different reaction parameters (e.g.concentration, precursor, composition, additives), reference samples (e.g.background, pure precursors) and replicates (to demonstrate reproducibility) with enhanced consistency afforded by the quasi-simultaneous nature of the measurements. The large sample volumes, compared with those typically used for X-ray scattering measurements, are on a similar scale to those in the laboratory, making the results more directly comparable.

Chemistry↗

Origin of Rapid Delithiation In Secondary Particles Of LiNi 0.8 Co 0.15 Al 0.05 O 2 and LiNi y Mn z Co 1− y − z O 2 Cathodes

Abstract Most research on the electrochemical dynamics in materials for high‐energy Li‐ion batteries has focused on the global behavior of the electrode. This approach is susceptible to misleading analyses resulting from idiosyncratic kinetic conditions, such as surface impurities inducing an apparent two‐phase transformation within LiNi 0.8 Co 0.15 Al 0.05 O 2 . Here, nano‐focused X‐ray probes are used to measure delithiation operando at the scale of secondary particle agglomerates in layered cathode materials during charge. After an initial latent phase, individual secondary particles undergo rapid, stochastic, and largely uniform delithiation, which is in contrast with the gradual increase in cell potential. This behavior reproduces across several layered oxides. Operando X‐ray microdiffraction (‐XRD) leverages the relationship between Li content and lattice parameter to further reveal that rate acceleration occurs between Li‐site fraction ( x Li ) ≈0.9 and ≈0.5 for LiNi 0.8 Co 0.15 Al 0.05 O 2 . Physics‐based modeling shows that, to reproduce the experimental results, the exchange current density ( i 0 ) must depend on x Li , and that i 0 should increase rapidly over three orders of magnitude at the transition point. The specifics and implications of this jump in i 0 are crucial to understanding the charge‐storage reaction of Li‐ion battery cathodes.

25 ENERGY STORAGE↗

Probing how Ti- and Nb-substitution affect the stability and improve the electrochemical performance of β- and ε-LiVOPO 4

LiVOPO 4 is a promising next-generation multi-electron cathode material, boasting a theoretical capacity of 305 mA h g -1 , significantly higher than any commercially used Li-ion battery cathode material. However, the material still faces several limitations, including the difficulty in attaining the full theoretical capacity at higher rates and capacity fade over several cycles. Here, in this paper, we show that Ti- and Nb-substitution can be used to improve the thermal stability and electrochemical performance of LiVOPO 4 . We show through in situ heating with XRD and a novel gradient heating technique that both Ti- and Nb-substitution cause β-LiVOPO 4 to be stabilized relative to ε-LiVOPO 4 . This is due to transition-metal substitution, which increases the O-vacancy formation energies, pushing the β → ε transition to higher temperatures. We show that it is still possible to synthesize pure-phase ε-LiVOPO 4 through the use of high temperatures to generate these O-vacancies. We show that even 1% of Ti- or Nb-substitution can improve the initial capacity and long term cycling capability of LiVOPO 4 by improving the high-voltage capacity and reducing the capacity fade in both the high- and low-voltage regions. This is due to the overall improved Li + ion diffusion which is caused by an improved charge-transfer resistance during cycling.

25 ENERGY STORAGE↗

A stable cathode-solid electrolyte composite for high-voltage, long-cycle-life solid-state sodium-ion batteries

Rechargeable solid-state sodium-ion batteries (SSSBs) hold great promise for safer and more energy-dense energy storage. However, the poor electrochemical stability between current sulfide-based solid electrolytes and high-voltage oxide cathodes has limited their long-term cycling performance and practicality. Here, we report the discovery of the ion conductor Na 3-x Y 1-x Zr x Cl 6 (NYZC) that is both electrochemically stable (up to 3.8 V vs. Na/Na + ) and chemically compatible with oxide cathodes. Its high ionic conductivity of 6.6 × 10 –5 S cm –1 at ambient temperature, several orders of magnitude higher than oxide coatings, is attributed to abundant Na vacancies and cooperative MCl 6 rotation, resulting in an extremely low interfacial impedance. A SSSB comprising a NaCrO 2 + NYZC composite cathode, Na 3 PS 4 electrolyte, and Na-Sn anode exhibits an exceptional first-cycle Coulombic efficiency of 97.1% at room emperature and can cycle over 1000 cycles with 89.3% capacity retention at 40 °C. These findings highlight the immense potential of halides for SSSB applications.

99 GENERAL AND MISCELLANEOUS↗

Intrinsic Kinetic Limitations in Substituted Lithium-Layered Transition-Metal Oxide Electrodes

Substituted Li-layered transition-metal oxide (LTMO) electrodes such as Li x Ni y Mn z Co 1-y-z O 2 (NMC) and Li x Ni y Co 1-y-z Al z O 2 (NCA) show reduced first cycle Coulombic efficiency (90-87% under standard cycling conditions) in comparison with the archetypal Li x CoO 2 (LCO; similar to 98% efficiency). Focusing on Li x Ni 0.8 Co 0.15 Al 0.0.5 O 2 as a model compound, we use operando synchrotron X-ray diffraction (XRD) and nuclear magnetic resonance (NMR) spectroscopy to demonstrate that the apparent first-cycle capacity loss is a kinetic effect linked to limited Li mobility at x > 0.88, with near full capacity recovered during a potentiostatic hold following the galvanostatic charge- discharge cycle. This kinetic capacity loss, unlike many capacity losses in LTMOs, is independent of the cutoff voltage during delithiation and it is a reversible process. The kinetic limitation manifests not only as the kinetic capacity loss during discharge but as a subtle bimodal compositional distribution early in charge and, also, a dramatic increase of the charge-discharge voltage hysteresis at x > 0.88. 7 Li NMR measurements indicate that the kinetic limitation reflects limited Li transport at x > 0.86. Electrochemical measurements on a wider range of LTMOs including Li x (Ni,Fe) y Co 1-y O 2 suggest that 5% substitution is sufficient to induce the kinetic limitation and that the effect is not limited to Ni substitution. In this paper, we outline how, in addition to a reduction in the number of Li vacancies and shrinkage of the Li-layer size, the intrinsic charge storage mechanism (two-phase vs solid-solution) and localization of charge give rise to additional kinetic barriers in NCA and nonmetallic LTMOs in general.

25 ENERGY STORAGE↗

Synthesis and optimized formulation for high-capacity manganese fluoride (MnF 2 ) electrodes for lithium-ion batteries

Electrochemical activity of poorly conductive metal fluorides in Li-ion batteries is contingent on their nanostructuration to reduce diffusion lengths and increase reaction kinetics. In that regard, we optimize the synthesis and electrode formulation of MnF 2 to enable sufficient electrochemical activity required to study its electrochemical conversion reaction mechanism. Solvothermal synthesis in a water–ethanol mixture (1:1 Vol.), using Mn acetate and a slight excess of hydrofluoric acid (HF), results in pure phase, nanosized (˜30 nm diameter) rutile-type MnF 2 ( P 4 2 /mnm). High energy ball-milling of MnF2–carbon mixtures leads to an amorphization of MnF 2 and its partial phase transformation to the α-PbO 2 -type structure, without significant improvement of the electrochemical performance. Changing the electrode binder, however, from typical polyvinylidene fluoride (PVDF) to water-soluble Na-alginate, leads to a significant improvement of the reversibility of the electrochemical reaction. Here, we attribute this drastic improvement to the improved adherence and homogeneity of the electrode film prepared with Na-alginate.

25 ENERGY STORAGE↗

Quantifying Reaction and Rate Heterogeneity in Battery Electrodes in 3D through Operando X-ray Diffraction Computed Tomography

In composite battery electrode architectures, local limitations in ionic and electronic transport can result in nonuniform energy storage reactions. Understanding such reaction heterogeneity is important to optimizing battery performance, including rate capability and mitigating degradation and failure. Here, we use spatially resolved X-ray diffraction computed tomography to map the reaction in a composite electrode based on the LiFePO 4 active material as it undergoes charge and discharge. Accelerated reactions at the electrode faces in contact with either the separator or the current collector demonstrate that both ionic and electronic transport limit the reaction progress. The data quantify how nonuniformity of the electrode reaction leads to variability in the charge/discharge rate, both as a function of time and position within the electrode architecture. Importantly, this local variation in the reaction rate means that the maximum rate that individual cathode particles experience can be substantially higher than the average, control charge/discharge rate, by a factor of at least 2-5 times. As a result, this rate heterogeneity may accelerate rate-dependent degradation pathways in regions of the composite electrode experiencing faster-than-average reaction and has important implications for understanding and optimizing rate-dependent battery performance. Benchmarking multiscale continuum model parameters against the observed reaction heterogeneity permits extension of these models to other electrode geometries.

25 ENERGY STORAGE↗

Reaction Heterogeneity in LiNi 0.8 Co 0.15 Al 0.05 O 2 Induced by Surface Layer

Through operando synchrotron powder X-ray diffraction (XRD) analysis of layered transition metal oxide electrodes of composition LiNi0.8Co0.15Al0.05O2 (NCA), we decouple the intrinsic bulk reaction mechanism from surface-induced effects. For identically prepared and cycled electrodes stored in different environments, we demonstrate that the intrinsic bulk reaction for pristine NCA follows solid-solution mechanism, not a two-phase as suggested previously. By combining high resolution powder X-ray diffraction, diffuse reflectance infrared Fourier transform spectroscopy (DRIFTS) and surface sensitive X-ray photoelectron spectroscopy (XPS), we demonstrate that adventitious Li2CO3 forms on the electrode particle surface during exposure to air, through reaction with atmospheric CO2. This surface impedes ionic and electronic transport to the underlying electrode, with progressive erosion of this layer during cycling giving rise to different reaction states in particles with an intact vs an eroded Li2CO3 surface-coating. This reaction heterogeneity, with a bimodal distribution of reaction states, has previously been interpreted as a “two-phase” reaction mechanism for NCA, as an activation step that only occurs during the first cycle. Similar surface layers may impact the reaction mechanism observed in other electrode materials using bulk probes such as operando powder XRD.

Grenier, Antonin↗