Search NASA⌕ Search

Engineering topics

Griffin, J. H.

Publications and source records attributed to Griffin, J. H..

17 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

The Application of Probabilistic Methods to the Mistuning Problem

FMM is a reduced order model for efficiently calculating the forced response of a mistuned bladed disk. FMM ID is a companion program which determines the mistuning in a particular rotor. Together, these methods provide a way to acquire data on the mistuning in a population of bladed disks, and then simulate the forced response of the fleet. This process is tested experimentally, and the simulated results are compared with laboratory measurements of a fleet of test rotors. The method is shown to work quite well. It is found that accuracy of the results depends on two factors: the quality of the statistical model used to characterize mistuning, and how sensitive the system is to errors in the statistical modeling.

Griffin, J. H.↗
NASA NTRS2003

System Identification of Mistuned Bladed Disks from Traveling Wave Response Measurements

A new approach to modal analysis is presented. By applying this technique to bladed disk system identification methods, one can determine the mistuning in a rotor based on its response to a traveling wave excitation. This allows system identification to be performed under rotating conditions, and thus expands the applicability of existing mistuning identification techniques from integrally bladed rotors to conventional bladed disks.

Feiner, D. M.↗
NASA NTRS1991

Friction damping of two-dimensional motion and its application in vibration control

This paper presents an approximate method for analyzing the two-dimensional friction contact problem so as to compute the dynamic response of a structure constrained by friction interfaces. The friction force at the joint is formulated based on the Coulomb model. The single-term harmonic balance scheme, together with the receptance approach of decoupling the effect of the friction force on the structure from those of the external forces has been utilized to obtain the steady state response. The computational efficiency and accuracy of the method are demonstrated by comparing the results with long-term time solutions.

Menq, C.-H.↗
NASA NTRS1989

How gravity and joint scaling affect dynamics response

If a scale model of a space structure is ground tested to establish dynamic characteristics of full-scale space structure, two factors need to be taken into consideration: the joint tolerances may not be scaled, and joint preloads (from gravity) may be present. In some situations, these differences may significantly affect dynamic response so that the model is not representative of the structure in space. In this study, joint effects are investigated by considering the response of a single-degree-of-freedom system that is restrained by a joint linkage. The joint is characterized by its initial stiffness, the load at which it slips, its hardening rate, and the distance it can slip (joint 'slop' or gap). The steady-state response of the system is calculated using a harmonic balance approach. It is found that the system response is multivalued for certain ranges of gap dimensions. When this is the case, small changes in system properties can lead to large differences in dynamic response and make it difficult to obtain meaningful results directly from model testing.

Hsu, S. T.↗
NASA NTRS1988

Transient response of joint dominated space structures - A new linearization technique

The linearization method presented for calculating the transient responses of nonlinear systems due to initial disturbances is an extension of the 'describing function' approach, in which the system's steady-state response is calculated by representing such nonlinear elements as space structure joints with impedances that are functions of response amplitude. It is shown that, for the transient case, the steady-state impedances can be averaged over the range of responses in order to furnish equivalent values of stiffness and damping; these, for a given set of initial displacements, may be treated as constant during calculations of system response.

Foelsche, G. A.↗
NASA NTRS1987

Bladed disk vibration

The objective was to better understand the vibratory response of bladed disk assemblies that occur in jet engines or turbopumps. Two basic problems were investigated: how friction affects flutter; and how friction, mistuning, and stage aerodynamics affect resonance. Understanding these phenomena allows a better understanding of why some stages have high vibratory stresses, how best to manage those stresses, and what to do about reducing them if they are too large.

Griffin, J. H.↗
NASA NTRS1987

An integrated approach for friction damper design

A procedure is outlined for determining the optimal design of friction dampers for high speed turbomachinery blading. The procedure includes: an integration of bench test results with finite element analysis and a single mode blade model to ensure accuracy of the analytical model and improve reliability of the friction damper design; an extension of the single mode blade model to predict the engine behavior of friction dampers; and a new way of viewing analytical and experimental results to determine optimal design parameters when the levels of excitation and damping in the system are unknown. Analysis and experiments are performed on a test disk in order to demonstrate and verify the accuracy of the design procedure.

Cameron, T. M.↗
NASA NTRS1986

Influence of friction dampers on torsional blade flutter

This paper deals with the stabilizing effects of dry friction on torsional blade flutter. A lumped parameter model with single degree of freedom per blade has been used to represent the rotor stage. The well-known cascade theories for incompressible and supersonic flows have been used to determine the allowable increase in fluid velocity relative to the blade. It has been found that the effectiveness of friction dampers in controlling flutter can be substantial.

Sinha, A.↗
NASA NTRS1985

Stability of limit cycles in frictionally damped and aerodynamically unstable rotor stages

This paper deals with the stability of limit cycles (Steady-State Oscillations) associated with the multi-degree-of-freedom model of a frictionally damped and aerodynamically unstable rotor stage. By using the first order averaging technique, a generalized criterion has been established to sort out those unstable limit cycles which govern the maximum transient amplitude beyond which the rotor stage becomes unstable.The stability of the remaining steady-state solutions is analyzed by linearizing the averaged system of differential equations. Numerical results are discussed for three-, four- and five-bladed disks.

Sinha, A.↗
NASA NTRS1985

The effect of limiting aerodynamic and structural coupling in models of mistuned bladed disk vibration

A model has been developed for studying the effect of mistuning on bladed disk vibration which has the unique feature that the extent of aerodynamic and structural interaction which it simulates can be readily varied from full coupling of all blades on the disk to coupling of each blade with only its nearest neighbors. Simulations utilizing the resulting algorithm show that limited coupling models may be used to predict the statistical distribution of blade amplitudes that characterizes the mistuning effect, which in turn determines stage durability. This approach is used to study the effect of changing various system parameters on amplitude scatter. Gas density, the number of blades on the disk, disk stiffness, and the engine order of the excitation are considered. The results are used to draw some conclusions about how to improve laboratory tests and component design.

Basu, P.↗
NASA NTRS1984

The interaction between mistuning and friction in the forced response of bladed disk assemblies

This paper summarizes the results of an investigation to establish the impact of mistuning on the performance and design of blade-to-blade friction dampers of the type used to control the resonant response of turbine blades in gas turbine engines. In addition, it discusses the importance of friction slip force variations on the dynamic response of shrouded fan blades.

Griffin, J. H.↗
NASA NTRS1984

Model development and statistical investigation of turbine blade mistuning

This paper discusses the development of an efficient algorithm which calculates the individual blade response of a bladed turbine disk, the subsequent statistical investigation to establish mistuning dependencies, and procedures which reduce the increase in blade amplitudes caused by mistuning.

Griffin, J. H.↗
NASA NTRS1983

Effects of friction dampers on aerodynamically unstable rotor stages

Attention is given to the physical concepts and mathematical techniques useful in the analysis of the stabilizing effect of friction on aerodynamically unstable rotor stages. Results are presented for three-, four-, and five-bladed disks. In the present multidegree-of-freedom model of an aerodynamically unstable rotor stage, a harmonic steady state solution due to the friction dampers may be either a stability limit, a stable cycle limit, or neither. A criterion is established in the form of an energy function which determines whether the solution is a stability limit. In the event that the initial displacement and velocity exeed those associated with the steady state solution corresponding to a stability limit, the reponse becomes unbounded.

Griffin, J. H.↗
NASA NTRS1983

Friction damping of flutter in gas turbine engine airfoils

This paper investigates the feasibility of using blade-to-ground friction dampers to stabilize flutter in blades. The response of an equivalent one mode model in which the aerodynamic force is represented as negative viscous damping is examined to investigate the following issues: the range of amplitudes over which friction damping can stabilize the response, the maximum negative aerodynamic damping that can be stabilized in such a manner, the effect of simultaneous resonant excitation on these stability limits, and the determination of those damper parameters which will be the best for flutter control.

Sinha, A.↗
NASA NTRS1975

International Ultraviolet Explorer (IUE) satellite mission analysis

The results are presented of the mission analysis performed by Computer Sciences Corporation (CSC) in support of the International Ultraviolet Explorer (IUE) satellite. The launch window is open for three separate periods (for a total time of 7 months) during the year extending from July 20, 1977, to July 20, 1978. The synchronous orbit shadow constraint limits the launch window to approximately 88 minutes per day. Apogee boost motor fuel was computed to be 455 pounds (206 kilograms) and on-station weight was 931 pounds (422 kilograms). The target orbit is elliptical synchronous, with eccentricity 0.272 and 24 hour period.

Cook, R. A.↗