Engineering topics

Griffin, L. W.

Publications and source records attributed to Griffin, L. W..

5 records

NASA NTRS2002

Full and Partial Admission Performance of the Simplex Turbine

The turbines used in rocket-engine applications are often partial-admission turbines, meaning that the flow enters the rotor over only a portion of the annulus. These turbines have been traditionally analyzed, however, assuming full-admission characteristics. This assumption enables the simulation of only a portion of the 360-degree annulus, with periodic boundary conditions applied in the circumferential direction. While this traditional approach to the simulating the flow in partial-admission turbines significantly reduces the computational requirements, the accuracy of the solutions has rarely been evaluated. In the current investigation, both full- and partial-admission three dimensional unsteady Navier-Stokes simulations were performed for a partial-admission turbine designed and tested at NASA Marshall Space Flight Center. The results indicate that the partial-admission nature of the turbine must be included in simulations to properly predict the performance and flow unsteadiness of the turbine.

Dorney, D. J.↗

NASA NTRS1993

Computational Fluid Dynamics (CFD) applications in rocket propulsion analysis and design

Computational Fluid Dynamics (CFD) has been used in recent applications to affect subcomponent designs in liquid propulsion rocket engines. This paper elucidates three such applications for turbine stage, pump stage, and combustor chamber geometries. Details of these applications include the development of a high turning airfoil for a gas generator (GG) powered, liquid oxygen (LOX) turbopump, single-stage turbine using CFD as an integral part of the design process. CFD application to pump stage design has emphasized analysis of inducers, impellers, and diffuser/volute sections. Improvements in pump stage impeller discharge flow uniformity have been seen through CFD optimization on coarse grid models. In the area of combustor design, recent CFD analysis of a film cooled ablating combustion chamber has been used to quantify the interaction between film cooling rate, chamber wall contraction angle, and geometry and their effects of these quantities on local wall temperature. The results are currently guiding combustion chamber design and coolant flow rate for an upcoming subcomponent test. Critical aspects of successful integration of CFD into the design cycle includes a close-coupling of CFD and design organizations, quick turnaround of parametric analyses once a baseline CFD benchmark has been established, and the use of CFD methodology and approaches that address pertinent design issues. In this latter area, some problem details can be simplified while retaining key physical aspects to maintain analytical integrity.

Mcconnaughey, P. K.↗

NASA NTRS1992

Design of advanced turbopump drive turbines for National Launch System application

The aerodynamic design of advanced fuel and oxidizer pump drive turbine systems being developed for application in the main propulsion system of the National Launch System are discussed. The detail design process is presented along with the final baseline fuel and oxidizer turbine configurations. Computed airfoil surface static pressure distributions and flow characteristics are shown. Both turbine configurations employ unconventional high turning blading (approximately 160 deg) and are expected to provide significant cost and performance benefits in comparison with traditional configurations.

Huber, F. W.↗

NASA NTRS1990

Numerical prediction of axial turbine stage aerodynamics

A preliminary assessment is made of two NASA-developed unsteady turbine stage computer codes. The methodology and previous partial validation of the codes are briefly outlined. Application of these codes to a Space Shuttle main engine turbine for two sets of operating conditions is then described. Steady and unsteady, two and three-dimensional results are presented, compared, and discussed. These results include time-mean and instantaneous airfoil pressure distributions and pressure fluctuations, streamlines on the airfoil surfaces and endwalls, and relative total pressure contours at different axial locations in the rotor passage. Although not available at the time of this writing, experimental data for one of the operating conditions simulated is forthcoming and will be used to assess the accuracy of the unsteady, as well as, the steady predictions presented. Issues related to code usage and resource requirements of the two codes are also discussed.

Mcconnaughey, H. V.↗

NASA NTRS1989

Prediction of the aerodynamic environment and heat transfer for rotor-stator configurations

A numerical study of the aerodynamic and thermal environment associated with axial turbine stages is presented. Computations were performed using a modification of the unsteady viscous code, ROTORI, and an improved version of the steady inviscid cascade system, MERIDL-TSONIC, coupled with boundary layer codes, BLAYER and STAN5. Two different turbine stages were analyzed: the first stage of the United Technologies Research Center Large Scale Rotating Rig (LSRR) and the first stage of the Space Shuttle Main Engine (SSME) high pressure fuel turbopump turbine. The time-averaged airfoil midspan pressure and heat transfer profiles were predicted for numerous thermal boundary conditions including adiabatic wall, prescribed surface temperature, and prescribed heat flux. Computed solutions are compared with each other and with experimental data in the case of the LSRR calculations. Modified ROTORI predictions of unsteady pressure envelopes and instantaneous contour plots are also presented. Relative merits of the two computational approaches are discussed.

Griffin, L. W.↗