Search NASA⌕ Search

Engineering topics

Griffin, Michael B.

Publications and source records attributed to Griffin, Michael B..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Cycloalkane-rich sustainable aviation fuel production via hydrotreating lignocellulosic biomass-derived catalytic fast pyrolysis oils

Sustainable aviation fuel (SAF) produced from lignocellulosic biomass is emerging as an ideal alternative to conventional jet fuel for aviation sector decarbonization. Catalytic fast pyrolysis (CFP) can convert lignocellulosic biomass into relatively stable bio-oil that can be selectively transformed to various transportation fuels through hydroprocessing under conditions of different severities. In this contribution, two CFP oils produced from pine-based feedstocks over different types of catalysts (i.e., ZSM-5 and Pt/TiO 2 catalysts) were hydrotreated at 125 bar in a non-isothermal process with a maximum temperature of 385 °C over a sulfided NiMo/Al 2 O 3 catalyst to produce SAF with high cycloalkane concentrations of 89–92 wt%. Cycloalkanes are an important component of jet fuel with advantageous fuel properties, such as high energy density, low sooting, and potential for replacing aromatic hydrocarbons to provide good seal swelling properties. The hydrotreating process successfully converted 91–92% of the biogenic carbon in the CFP oil intermediates to liquid-phase hydrotreated products. Through distillation, 39–40 wt% of the hydrotreated oils were collected in the jet-fuel range as SAF fractions. The rest of the hydrotreated product could be valorized as fuels (e.g., diesel) or chemicals. The SAF fractions with oxygen contents below the detection limit (<0.01 wt%) met ASTM D7566 finished fuel blend and D4054 Tier 1 specifications with respect to density, lower heating value (LHV), volatility, flash point, and freeze point. These results indicate hydrotreating lignocellulosic biomass-derived CFP oil as a promising pathway to produce high-quality SAF rich in cycloalkanes. Continued research is required to increase the SAF yield by process improvements, such as increased CFP oil yields, and an enhanced production of SAF-range molecules via e.g., cracking of high-molecular weight compounds either during CFP or hydrotreating, as well as evaluation of a broader range of jet fuel properties and performance requirements.

09 BIOMASS FUELS↗
DOE OSTI2024

Opening pathways for the conversion of woody biomass into sustainable aviation fuel via catalytic fast pyrolysis and hydrotreating

Meeting aggressive decarbonization targets set by the International Civil Aviation Organization (ICAO) will require the rapid development of technologies to produce sustainable aviation fuel (SAF). Catalytic fast pyrolysis (CFP) can support these efforts by opening pathways for the conversion of woody biomass into an upgraded biogenic oil that can be further processed to SAF and other fuels. However, the absence of end-to-end experimental data for the process leads to uncertainty in the yield, product quality, costs, and sustainability of the pathway. The research presented here serves to address these needs through a series of integrated experimental campaigns in which real biomass feedstocks are converted to a final SAF product using large bench-scale continuous reactor systems. For these campaigns, the degree of catalytic upgrading during CFP was varied to produce CFP-oils with oxygen contents of 17 and 20 wt% on a dry basis. The CFP-oils were then hydrotreated and distilled into gasoline, diesel, and SAF fractions. Detailed yield and compositional data were obtained for each step of the process to inform technoeconomic and lifecycle analyses, and the fuel properties of the SAF fraction were evaluated to provide first-of-its-kind insight into the quality of the final product. This research reveals opportunities to optimize process carbon efficiency by tuning the degree of catalytic upgrading during the CFP step and highlights routes to produce a high-quality cycloalkane-rich SAF with 85–92% reduction in greenhouse gas emissions compared to fossil-based pathways.

09 BIOMASS FUELS↗
DOE OSTI2023

Catalytic pyrolysis as a platform technology for supporting the circular carbon economy

Catalytic pyrolysis, a process that combines pyrolysis and vapour-phase catalytic upgrading, is a versatile technology platform capable of direct liquefaction of biomass and waste plastic into intermediates that can enable the decarbonized production of chemicals and/or transportation fuels. Recently, catalytic pyrolysis has attracted substantial research and commercialization attention, with over 15,000 journal articles and patents published in the past decade alone. Here, in this Perspective, we chart a path towards commercial-scale catalytic pyrolysis of waste plastic and biomass by identifying key short-term and long-term technological barriers. Within the proposed development roadmap addressing these barriers, catalytic pyrolysis can move from the demonstration scale to integrated biorefinery networks producing fuels and plastics precursors at a scale of between 0.1 and 1 billion tonnes of carbon per year.

09 BIOMASS FUELS↗
DOE OSTI2023

Towards improved conversion of wet waste to jet fuel with atomic layer deposition-coated hydrodeoxygenation catalysts

The conversion of wet waste-derived volatile fatty acids into jet fuel-range hydrocarbons is a promising route for increasing the production of sustainable aviation fuel; however, the cost and moderate alkane selectivity of Pt-based hydrodeoxygenation catalysts present challenges for commercialization. Here, to address this, we used atomic layer deposition to apply TiO 2 overcoats to Pt/Al 2 O 3 catalysts and create new interface sites that exhibited 8 times higher site time yield of the desirable n-alkane product than uncoated catalyst. Through TPR/TPD, XPS, CO DRIFTS, and DFT calculations, we found that the increased selectivity of the ALD-coated catalyst was due to the creation of O vacancies at the Pt-TiO 2 interface under reducing conditions, resulting in new Ti 3+ acid sites near the active metal. Maximum conversion and alkane selectivity during HDO was achieved with an ALD-coated 0.5% wt Pt catalyst, indicating that TiO 2 ALD can be used to maximize the utility of precious-metal catalysts.

09 BIOMASS FUELS↗
DOE OSTI2022

Model quantification of the effect of coproducts and refinery co-hydrotreating on the economics and greenhouse gas emissions of a conceptual biomass catalytic fast pyrolysis process

Here we present model results for a scaled-up conceptual process informed by bench scale biomass catalytic fast pyrolysis (CFP) and hydrotreating experimental data. This process uses a Pt/TiO 2 catalyst during CFP, which produces a partially deoxygenated organic biocrude intermediate that is then hydroprocessed to a hydrocarbon fuel blendstock; the catalyst also enables high yields of acetone and methyl-ethyl-ketone (MEK) coproducts. Two options for hydroprocessing were modeled: (A) co-hydrotreating at a petroleum refinery using hydrogen sourced from steam reforming of natural gas and (B) standalone hydrotreating at a biorefinery using hydrogen sourced from CFP off gases. The results revealed that Case A was economically advantageous with a modeled minimum fuel selling price (MFSP) of $\$$2.83/GGE or gallon gasoline equivalent (in 2016 US dollars), while the additional cost of standalone hydrotreating facilities in Case B increased the MFSP to $3.13/GGE. Conversely, greenhouse gas (GHG) emissions were lower for Case B (3.9 g CO 2 e/MJ) compared to Case A (21.5 g CO 2 e/MJ) due to the use of biogenic (Case B) and fossil-derived (Case A) hydrogen. In a third option (Case C), the requirements for separation and purification of acetone and MEK were removed from the refinery co-processing scenario (Case A) to evaluate the impacts of this process simplification. Elimination of these coproducts increased the MFSP to $3.21/GGE and GHG emissions to 35 g CO 2 e/MJ. These comparisons based on our detailed conceptual models provide economic and sustainability guidance regarding processing choices for future biorefineries. While refinery coprocessing using existing equipment and the production of relatively valuable coproducts can benefit the economics, the hydrogen-source and biogenic coproducts can have significant impacts on the sustainability of the process, and feasibility to use CFP off-gases or other renewable sources for hydrogen production can help lower GHG emissions.

09 BIOMASS FUELS↗
DOE OSTI2022

Sustainable Aviation Fuel via Hydroprocessing of Catalytic Fast Pyrolysis Oil

Cycloalkanes have been identified as a promising alternative for sustainable aviation fuel (SAF) in a recent US Department of Energy Review of Technical Pathways to SAF. Cycloalkanes can provide desirable SAF properties, including energy density, and, in addition, they may be able to provide necessary seal swelling and leakage protection and replace undesirable aromatics in aviation fuel. Catalytic fast pyrolysis (CFP) followed by hydroprocessing constitutes a platform well suited for converting biomass to cycloalkanes. CFP oils are rich in phenolic compounds and, depending on CFP catalyst, in aromatic hydrocarbons, which can both be hydrogenated to form cycloalkanes. In this work, we report results from hydroprocessing of two types of CFP oil to produce fractions boiling in the sustainable aviation fuel range and meeting tested aviation fuel specifications. CFP oils prepared over a zeolite catalyst (ZSM-5) and a hydrodeoxygenation catalyst (Pt/TiO2) were hydroprocessed over a sulfided NiMo/Al2O3 catalyst in a two-stage process (1st stage ~250 degrees C and 2nd stage 385 degrees C) in a continuous trickle-bed hydrotreater. The hydrotreated product contained 39-40% material boiling in the SAF range by distillation with a carbon efficiency of 36-37% from CFP oil to SAF fraction. The SAF fractions consisted of 82-87% of cycloalkanes, had non-detectable oxygen contents and lower heating values (LHV) above the jet fuel minimum limit of 42.8 MJ/kg. The SAF-range product also had acceptable volatility and freeze and flash points per aviation fuel specifications. The results suggest a promising pathway for SAF production via the catalytic fast pyrolysis pathway. Methods to enhance the yield of SAF will be discussed.

BASIC BIOLOGICAL SCIENCES,BIOMASS FUELS↗
DOE OSTI2022

Investigating Deposition Sequence During Synthesis of Pd/Al2O3 Catalysts Modified with Organic Monolayers

Modification of supported metal catalysts with self-assembled monolayers (SAMs) has been shown to improve selectivity and turnover frequencies (TOFs) for many catalytic reactions. However, these benefits are often accompanied by a decrease in overall mass activity due to partial blocking of active sites by the monolayers. Therefore, a potential method for increasing site accessibility is to deposit the active metal (e.g., Pd) after deposition of a SAM modifier on the support material. In this work, Pd/Al2O3 catalysts were synthesized using both a conventional, "metal-first" sequence in which the phosphonic acid (PA) SAM was deposited on Pd/Al2O3 and a "SAM-first" technique in which the ligands were deposited onto the support prior to deposition of the metal. Although metal-first catalysts showed a significant increase in TOF during benzyl alcohol HDO, they exhibited only a modest increase in overall mass activity due to a decrease in the number of active sites. Meanwhile, SAM-first catalysts showed similar improvements in TOF and toluene selectivity but exhibited significantly improved HDO rates compared to metal-first catalysts. The rate increase was attributed to reduced site blocking as evidenced by CO chemisorption measurements. Additionally, analysis of catalysts having high Pd loadings using transmission electron microscopy (TEM) showed that SAM-first catalysts generally resulted in lower average particle sizes than traditionally modified and unmodified catalysts, suggesting that precoating the support surface with PAs changes the way that Pd is deposited during incipient wetness, leading here to improved activity.

catalytic reactions↗
DOE OSTI2021

Deactivation by Potassium Accumulation on a Pt/TiO 2 Bifunctional Catalyst for Biomass Catalytic Fast Pyrolysis

Biomass-derived feedstocks bring significant challenges to the longevity of the catalysts used for their conversion, and alkali metals, for example, K, in the feedstock have been widely ascribed as one of the important factors causing catalyst deactivation. To address this challenge, it is critical to understand the mechanism of catalyst deactivation caused by K accumulation to guide the improvement of catalysts and processes and the development of catalyst regeneration strategies. In this work, we report a deep understanding of the impact of K on a bifunctional Pt/TiO 2 catalyst, which is an efficient catalyst for the ex situ catalytic fast pyrolysis of biomass. We simulated the K-poisoning of Pt/TiO 2 catalysts by purposely loading different amounts of K (100-6000 ppm by weight) on the catalysts. A series of characterization approaches, including scanning transmission electron microscopy, Fourier transform infrared spectroscopy, and chemical titration, were combined with a kinetic assessment of multiple probe reactions to elucidate the mechanism of Pt/TiO 2 deactivation by K accumulation. At low K loadings (<800 ppm), K preferentially poisons the strong Lewis acid sites, leading to significantly reduced activity for acid-catalyzed alcohol dehydration. However, acetone condensation is less sensitive to the poisoning of strong Lewis acid sites. Reactions that occur on Pt sites or at the metal-support interface, including alkene hydrogenation, m-cresol hydrodeoxygenation (HDO), and CO oxidation, were not impacted. At high K loadings (>800 ppm), K starts to accumulate on the Pt-TiO 2 interfacial area, poisoning the interfacial active sites for HDO and CO oxidation reactions. We further found that the poisoning of the Pt/TiO 2 catalyst by K is reversible, and water washing can successfully remove the accumulated K and recover the activities for both alcohol dehydration and m-cresol HDO reactions.

09 BIOMASS FUELS↗
DOE OSTI2021

Performing In Situ Closed-Cell Gas Reactions in the Transmission Electron Microscope

Gas reactions studied by in situ electron microscopy can be used to capture the real-time morphological and microchemical transformations of materials at length scales down to the atomic level. In situ closed-cell gas reaction (CCGR) studies performed using (scanning) transmission electron microscopy (STEM) can separate and identify localized dynamic reactions, which are extremely challenging to capture using other characterization techniques. For these experiments, we used a CCGR holder that utilizes microelectromechanical systems (MEMS)-based heating microchips (hereafter referred to as "E-chips"). The experimental protocol described here details the method for performing in situ gas reactions in dry and wet gases in an aberration-corrected STEM. This method finds relevance in many different materials systems, such as catalysis and high-temperature oxidation of structural materials at atmospheric pressure and in the presence of various gases with or without water vapor. Here, several sample preparation methods are described for various material form factors. During the reaction, mass spectra obtained with a residual gas analyzer (RGA) system with and without water vapor further validates gas exposure conditions during reactions. Integrating an RGA with an in situ CCGR-STEM system can, therefore, provide critical insight to correlate gas composition with the dynamic surface evolution of materials during reactions. In situ/operando studies using this approach allow for detailed investigation of the fundamental reaction mechanisms and kinetics that occur at specific environmental conditions (time, temperature, gas, pressure), in real-time, and at high spatial resolution.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Atomic Layer Deposition with TiO2 for Enhanced Reactivity and Stability of Aromatic Hydrogenation Catalysts

Hydrogenation of aromatic molecules in fossil- and bio-derived fuels is essential for decreasing emissions of harmful combustion products and addressing growing concerns around urban air pollution. In this work, we used atomic layer deposition to significantly enhance the hydrogenation performance of a conventional supported Pd catalyst by applying an ultrathin coating of TiO2 in a scalable powder coating process. The TiO2-coated catalyst showed substantial gains in the conversion of multiple aromatic molecules, including a 5-fold improvement in turnover frequency versus the uncoated catalyst in the hydrogenation of naphthalene. This activity enhancement was maintained upon scaling the coating synthesis process from 3 to 100 g. Based on the results from Xray photoelectron spectroscopy, X-ray absorption spectroscopy, and computational modeling, the activity enhancement was attributed to ensemble effects resulting from partial TiO2 coverage of the Pd surface rather than fundamental changes to the Pd electronic structure. Additional durability testing confirmed that the TiO2 coating improved the thermal and hydrothermal stability of the catalyst as well as tolerance toward sulfur impurities in the reactant stream. Using an economic model of an industrial deep hydrogenation process, we found that an increase in catalyst activity or lifetime of 2× would justify even a relatively high estimate for the cost of TiO2 atomic layer deposition coatings at scale

atomic layer↗
DOE OSTI2021

Assessing the Role of Interfacial and Metal Sites in Pt/TiO2-Catalyzed Acetic Acid Hydrodeoxygenation

The work summarized in this presentation builds off of these studies, utilizing atomic-scale modeling to discern the role of Pt-metal and Pt-TiO2-interfacial sites in promoting key C-C bond-breaking, C-O bond-breaking, and (de)hydrogenation steps in acetic acid HDO. By considering Pt(111) and Pt-TiO2-interface surface models, adsorption and reaction energetics calculated by density funcational theory provide fundamental insights into the role of both interfacial sites and oxygen vacancies in promoting desired deoxygenation pathways over undesired decarboxylation/decarbonylation pathways.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2021

Predicting Thermal Excursions During in situ Oxidative Regeneration of Packed Bed Catalytic Fast Pyrolysis Catalyst

Ex situ catalytic fast pyrolysis (CFP) uses a secondary reactor to upgrade biomass pyrolysis vapors to stabilized CFP oils with reduced oxygen content. In one configuration, the secondary reactor is operated as a packed-bed swing reactor system which allows coke-deactivated beds to be decarbonized in situ while other beds remain online for vapor upgrading. In situ decarbonization must be done carefully to avoid irreversible deactivation and/or physical degradation of catalyst pellets. Given that packed bed reactors are well known to have poor heat transfer characteristics, this is a critical issue impacting scaleability and commercial viability of the technology. To predict thermal excursions during regeneration, finite element computational models have been built to assist in scaling up oxidative decarbonization of a Pt/TiO2 CFP catalyst (0.5 mm spheres) from a bench scale packed bed with 100 g of catalyst to a pilot scale packed bed with 2 kg of catalyst and internal cooling tubes. Based on transient measurements of outlet temperature and effluent CO2 concentration, and using an assumed coke profile and activation energy, this paper demonstrates that specific combinations of effective thermal conductivity and wall heat transfer coefficient can fit bench scale oxidative regeneration data equally well. For the upscaled 2 kg bed, four bench-scale “best fit” parameter pairs give different predictions for location and magnitude of thermal excursions, with the maximum computed bed temperature gradients ranging from 30 °C cm-1 to as high as 3000 °C cm-1. The larger the fraction of heat removal by conduction through the cooling tubes, the greater the differences between the parameter pairs. The modelling results presented in this paper cast doubt on the industrial viability of the proposed combination of catalyst, bed and regeneration process, and point to the need for alternate reactor designs. However, there is considerable uncertainly in some of the key model parameters. The reliability of model predictions can be increased by adding more temperature measurements at key bed locations, testing additional variations in process conditions, performing careful bed dissections to determine the true coke profile, and perhaps most importantly, directly measuring the effective thermal conductivity of the catalyst pellets.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Organic Modifiers Promote Furfuryl Alcohol Ring Hydrogenation via Surface Hydrogen-Bonding Interactions

Interactions between surface adsorbed species can affect catalyst reactivity, and thus, the ability to tune these interactions is of considerable importance. Deposition of organic modifiers provides one method of intentionally introducing controllable surface interactions onto catalyst surfaces. In this study, Pd/Al2O 3 catalysts were modified with either thiol or phosphonic acid (PA) ligands and tested in the hydrogenation of furanic species. The thiol modifiers were found to inhibit ring hydrogenation (RH) activity, with the degree of inhibition trending with the thiol surface coverage. This suggests that thiols do not strongly interact with the reactants and simply serve to block active sites on the Pd surface. PAs, on the other hand, were found to enhance RH when furfuryl alcohol (FA) was used as the reactant. Density functional theory calculations suggested that this enhancement was due to hydrogen-bonding interactions between FA-derived surface intermediates and PA modifiers. Here, installation of hydrogen-bonding groups on the Pd surface served to preferentially stabilize RH product states. Furthermore, the promotional effect on the RH of FA was observed to be greater when a higher-coverage PA was used, providing a rate more than twice that of the unmodified Pd/Al2O 3 . The results of this work suggest that organic ligands can be designed to impart tunable surface interactions on heterogeneous catalysts, providing an additional method of controlling catalytic performance.

09 BIOMASS FUELS↗