Search NASA⌕ Search

Engineering topics

Groebner, R J

Publications and source records attributed to Groebner, R J.

Intrinsic rotation produced by ion orbit loss and X-loss

A practical calculation model for the intrinsic rotation imparted to the edge plasma by the directionally preferential loss of ions on orbits that cross the last closed flux surface is presented and applied to calculate intrinsic rotation in several DIII-D [J. Luxon, Nucl. Fusion 42, 614 (2002)] discharges. The intrinsic rotation produced by ion loss is found to be sensitive to the edge temperature and radial electric field profiles, which has implications for driving intrinsic rotation in future large tokamaks.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

The EPED pedestal model and edge localized mode-suppressed regimes: Studies of quiescent H-mode and development of a model for edge localized mode suppression via resonant magnetic perturbations

The EPED model predicts the H-mode pedestal height and width based upon two fundamental and calculable constraints: (1) onset of non-local peeling-ballooning modes at low to intermediate mode number, (2) onset of nearly local kinetic ballooning modes at high mode number. We present detailed tests of the EPED model in discharges with edge localized modes (ELMs), employing new high resolution measurements, and finding good quantitative agreement across a range of parameters. The EPED model is then applied for the first time to quiescent H-mode (QH), finding a similar level of agreement between predicted and observed pedestal height and width, and suggesting that the model can be used to predict the critical density for QH-mode operation. Finally, the model is applied toward understanding the suppression of ELMs with 3D resonant magnetic perturbations (RMP). Combining EPED with plasma response physics, a new working model for RMP ELM suppression is developed. We propose that ELMs are suppressed when a 'wall' associated with the RMP blocks the inward penetration of the edge transport barrier. A calculation of the required location of this 'wall' with EPED is consistent with observed profile changes during RMP ELM suppression and offers an explanation for the observed dependence on safety factor (q{sub 95}).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Pedestal density fluctuation dynamics during the inter-ELM cycle in DIII-D

Detailed 2D measurements of long-wavelength density fluctuations in the pedestal region with beam emission spectroscopy during the period between edge localized modes (ELMs) indicate two distinct bands of fluctuations propagating in opposite poloidal directions in the plasma frame: one lower frequency band (50-150 kHz) advects in the ion-diamagnetic drift direction (ion mode) and a higher frequency band (200-400 kHz) advects in the electron diamagnetic drift direction (electron mode). The ion mode amplitude is modulated with the ELM cycle: it increases rapidly after an ELM and then saturates, similar to the evolution of the pedestal electron pressure and density gradients. The electron mode, in contrast, has no significant time evolution between ELMs. The decorrelation time of the ion mode is <5 {mu}s[{tau}{sub c}(c{sub s}/c{sub s}aa){<=}1], the radial correlation length is of order 10 {rho}{sub i} and has poloidal wave-number k{sub {theta}{rho}i{approx}}0.1, and the mode advects at near the ion diamagnetic velocity in the plasma frame. These spatiotemporal dynamics are qualitatively similar to features predicted for kinetic ballooning modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Poloidally and radially resolved parallel D{sup +} velocity measurements in the DIII-D boundary and comparison to neoclassical computations

First measurements of the D{sup +} parallel velocity, V{sub ||}{sup D+}, in L-mode discharges in the DIII-D [J. L. Luxon, Nucl. Fusion 42, 614 (2002)] tokamak boundary region at two poloidal locations, {theta}{approx}0 deg. and {theta}{approx}255 deg., made using Mach probes, feature a peak with velocities of up to 80 km/s at the midplane last closed flux surface (LCFS), as high as ten times the charge exchange recombination C{sup 6+} toroidal velocity, V{sub {phi}}{sup C6+}, in the same location. The V{sub ||}{sup D+} profiles are very asymmetric poloidally, by a factor of 8-10, and feature a local peak at the midplane. This peak, 1-2 cm wide, is located at or just inside the LCFS, and it suggests a large source of momentum in that location. This momentum source is quantified at {approx}0.31 N m by using a simple momentum transport model. This is the most accurate measurement of the effects of so called 'intrinsic' edge momentum source to date. The V{sub ||}{sup D+} measurements are quantitatively consistent with a purely neoclassical computational modeling of V{sub ||}{sup D+} by the code NEO[E. A. Belli and J. Candy, Plasma Phys. Controlled Fusion 50, 095010 (2008)], using V{sub {phi}}{sup C6+} as input, for {rho}{approx}0.7-0.95 at the two poloidal locations, where V{sub ||}{sup D+} measurements exist. The midplane NEO-calculated V{sub ||}{sup D+} grows larger than V{sub ||}{sup C6+} in the steeper edge gradient region and trends to agreement with the probe-measured V{sub ||}{sup D+} data near {rho}{approx}1, where the local V{sub ||}{sup D+} velocity peak exists. The measurements and computations were made in OH and L-mode discharges on an upper single null, with ion {nabla}B{sub T} drift away from the divertor. The rotating layer finding is similar in auxiliary heated discharges with and without external momentum input, except that at higher density the edge velocity weakens.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Force balance and ion particle transport differences in high and low confinement tokamak edge pedestals

The various terms in the radial force balance in the edge plasma are evaluated using experimental data from the low (L) and high (H) confinement phase of a DIII-D [J. Luxon, Nucl. Fusion 42, 614 (2002)] discharge in order to investigate the differences in the radial force balance among the several electromagnetic and pressure gradient forces in L-mode and H-mode. The roles of cross-field toroidal momentum transport and of a radial pinch velocity in determining different radial particle fluxes in L-mode and H-mode are elucidated.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Measurements of the internal magnetic field using the B-Stark motional Stark effect diagnostic on DIII-D (inivited)

Results are presented from the B-Stark diagnostic installed on the DIII-D tokamak. This diagnostic provides measurements of the magnitude and direction of the internal magnetic field. The B-Stark system is a version of a motional Stark effect (MSE) diagnostic based on the relative line intensities and spacing of the Stark split D{sub {alpha}} emission from injected neutral beams. This technique may have advantages over MSE polarimetry based diagnostics in future devices, such as the ITER. The B-Stark diagnostic technique and calibration procedures are discussed. The system is shown to provide accurate measurements of B{sub {theta}}/B{sub T} and |B| over a range of plasma conditions. Measurements have been made with toroidal fields in the range of 1.2-2.1 T, plasma currents in the range 0.5-2.0 MA, densities between 1.7 and 9.0x10{sup 19} m{sup -3}, and neutral beam voltages between 50 and 81 keV. The viewing direction and polarization dependent transmission properties of the collection optics are found using an in situ beam into gas calibration. These results are compared to values found from plasma equilibrium reconstructions and the MSE polarimetry system on DIII-D.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Limits to the H-mode pedestal pressure gradient in DIII-D

The spatial and temporal evolution of the total pedestal pressure profile has been measured during the pedestal evolution between successive edge localized modes (ELMs) of type-I ELMing H-mode discharges in DIII-D. Measurements are used to test a model that predicts that kinetic ballooning modes (KBMs) provide a strong constraint on the pedestal pressure gradient obtained during an inter-ELM cycle and cause the pedestal width to scale as the square root of the pedestal poloidal beta. Discharges in two different parameter regimes are examined for evidence that the evolution of the pressure gradient reaches a limit prior to the onset of an ELM. Both discharges show evidence of rapid evolution of the pressure profile very early in the recovery phase from an ELM. In one discharge, the pressure gradient reached approximate steady state within similar to 3 ms after the ELM event. In the other discharge, the pressure gradient just inboard of the last closed flux surface reached steady state early in the ELM recovery phase even as the pedestal expanded into the core and the maximum pressure gradient continued to rise during the remainder of the ELM cycle. Simple quantitative theoretical metrics show that pressure gradients in both discharges reached levels that were large enough to excite KBMs. In addition, the peeling-ballooning theory for the onset of type-I ELMs and the EPED1 model for pedestal height and width make predictions consistent with the data of both discharges.

CONFINEMENT↗

Demonstration of ITER operational scenarios on DIII-D

The DIII-D programme has recently initiated an effort to provide suitably scaled experimental evaluations of four primary ITER operational scenarios. New and unique features of this work are that the plasmas incorporate essential features of the ITER scenarios and anticipated operating characteristics; e. g. the plasma cross-section, aspect ratio and value of I/aB of the DIII-D discharges match the ITER design, with size reduced by a factor of 3.7. Key aspects of all four scenarios, such as target values for beta(N) and H(98), have been replicated successfully on DIII-D, providing an improved and unified physics basis for transport and stability modelling, as well as for performance extrapolation to ITER. In all four scenarios, normalized performance equals or closely approaches that required to realize the physics and technology goals of ITER, and projections of the DIII-D discharges are consistent with ITER achieving its goals of >= 400MW of fusion power production and Q >= 10. These studies also address many of the key physics issues related to the ITER design, including the L-H transition power threshold, the size of edge localized modes, pedestal parameter scaling, the impact of tearing modes on confinement and disruptivity, beta limits and the required capabilities of the plasma control system. An example of direct influence on the ITER design from this work is a modification of the physics requirements for the poloidal field coil set at 15 MA, based on observations that the inductance in the baseline scenario case evolves to a value that lies outside the original ITER specification.

CONFINEMENT↗

Interpretation of particle pinches and diffusion coefficients in the edge pedestal of DIII-D H-mode plasmas

A procedure is described for evaluating particle pinches to be used in interpreting particle diffusion coefficients from measured density and temperature profiles in the edge pedestal of tokamak plasmas. Application to the interpretation of two DIII-D [J. Luxon, Nucl. Fusion 42, 614 (2002)]. discharges yields new information about particle pinches and particle diffusion coefficient profiles in the edge pedestal.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Plasma Shape Optimization for Steady-State Tokamak Development in DIII-D

For a more detailed account of the results summarized here and for references, see C.T. Holcomb et al., Phys. Plasmas 16, 056116 (2009). Advanced tokamak research on DIII-D is focused on developing a high fusion gain, steady-state scenario that would eliminate or greatly reduce the demands on an inductive transformer in future machines. Steady-state operation requires the inductively driven current density (j{sub Ind}) be zero everywhere. Most of the total current I{sub p} is typically from self-driven bootstrap current, with the remainder driven by external noninductive sources, such as neutral beam and radiofrequency current drive. This paper describes an extension of the fully noninductive condition (f{sub NI} {approx} 100%) to {approx}0.7 current relaxation times that was achieved by a combination of more available ECCD and new scientific insights. The insights are an optimization of performance through variation of the plasma shape parameter known as squareness ({zeta}) and an optimization of divertor magnetic balance. These optimizations simultaneously improve stability, confinement, and density control. These are each essential for achieving fully noninductive operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗