Engineering topics

Groth, M. (ORCID:0000000173971586)

Publications and source records attributed to Groth, M. (ORCID:0000000173971586).

3 records

DOE OSTI2024

Validation of the ERO2.0 code using W7-X and JET experiments and predictions for ITER operation

Abstract The paper provides an overview of recent modelling of global material erosion and deposition in the fusion devices Wendelstein 7-X (W7-X), JET and ITER using the Monte-Carlo code ERO2.0. For validating the modelling tool in a three-dimensional environment, W7-X simulations are performed to describe carbon erosion from the graphite test divertor units, which were equipped in operational phase OP 1.2 and analysed post-mortem. Synthetic spectroscopy of carbon line emission is compared with experimental results from the divertor spectrometer measurement system, showing a good agreement in the e-folding lengths in the radial intensity profiles of carbon. In the case of metallic wall materials, earlier modelling of the Be/W environment in JET and ITER is revisited and extended with an updated set of sputtering and reflection data, as well as including the mixing model for describing the Be/W dynamics in the divertor. Motivated by recent H/D/T isotope experiments in JET, limited and diverted configuration pulses are modelled, showing the expected trend of both Be and W erosion increasing with isotope mass. For the JET diverted configuration pulses, it is shown that Be migrates predominantly to the upper part of the inner divertor where it initially leads to strong W erosion. With longer exposure time, the growth of a Be deposited layer leads to a reduction of W erosion in that region. A similar trend is observed in simulations of the ITER baseline Q = 10 scenario, however with a more symmetric Be migration pattern leading to deposition also on the outer divertor.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Spectroscopic measurement of increases in hydrogen molecular rotational temperature with plasma-facing surface temperature and due to collisional-radiative processes in tokamaks

Abstract Spatially resolved rotational temperature of ground state hydrogen molecules desorbed from plasma-facing surface was measured in QUEST, LTX-β, and DIII-D tokamaks, and the increases of the rotational temperature with the surface temperature and due to collisional-radiative processes in the plasmas were evaluated. The increase due to collisional-radiative processes was calculated by solving rate equations considering electron and proton collisional excitation and deexcitation and spontaneous emission. The calculation results suggest a high sensitivity for the rotational temperature to electron and proton densities, but a negligible sensitivity to the electron, proton, and surface temperatures. In the three tokamaks with different plasma parameters and plasma-facing surface materials, the spatial profile of the rotational temperature was estimated using Fulcher-α emission lines (600–608 nm). In QUEST, the spatial profile of the rotational temperature was estimated from spatially resolved spectra. In the other tokamaks, the rotational temperature was evaluated assuming a single point emission with a location determined from the Fulcher-α emission profile as measured with a filtered camera. In metal-walled devices QUEST and LTX-β, the rotational temperature increased with the surface temperature, and the calculated collisional-radiative increase is consistent with measured increase assuming that the rotational temperature at the surface is approximately 500–600 K higher than the surface temperature. In DIII-D with carbon walls, a larger collisional-radiative increase than the other tokamaks was observed because of the higher density leading to a large difference from the calculated increase compared to the other smaller tokamaks. Measurement of the Fulcher-α emission profile with higher spatial resolution in DIII-D may reduce the difference and reveal the effect of the surface temperature on the rotational temperature. These results show the increases in the rotational temperature with the surface temperature and due to the collisional-radiative processes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2023

Parameter dependencies of the separatrix density in low triangularity L-mode and H-mode JET-ILW plasmas

Abstract The midplane electron separatrix density, n e,sep , in JET-ILW L-mode and H-mode low triangularity deuterium fuelled plasmas exhibits a strong explicit dependence on the averaged outer divertor target electron temperature, n e,sep ∼ T e,ot −1/2 . This dependence is reproduced by analytic reversed two point model (rev-2PM), and arises from parallel pressure balance, as well as the ratio of the power and momentum volumetric loss factors, (1 − f cooling )/(1 − f mom-loss ). Quantifying the influence of the (1 − f cooling ) and (1 − f mom-loss ) loss factors on n e,sep has been enabled by measurement estimates of these quantities from L-mode density (fueling) ramps in the outer horizontal, VH(C), and vertical target, VV, divertor configurations. Rev-2PM n e,sep estimates from the extended H-mode and more limited L-mode datasets are recovered to within ±25% of the measurements, with a scaling factor applied to account for use of T e,ot , an averaged quantity, rather than flux tube resolved target values. Both the (1 − f cooling ) and (1 − f mom-loss ) trends and recovery of n e,sep using the rev-2PM formatting are reproduced in EDGE2D-EIRENE L-mode-like and H-mode-like density scan simulations. The general lack of a divertor configuration effect in the JET-ILW n e,sep trends can be attributed to a significant influence of main chamber recycling, which has been shown in the EDGE2D-EIRENE results to moderate n e,sep with respect to changes in divertor neutral leakage imposed by changes in the divertor configuration. The unified n e,sep vs T e,ot trends can, however, be broken if large modifications to the divertor geometry (e.g. complete removal of the outer divertor baffle structure) are introduced in the model. The more pronounced high-field side high density region formation in the VH(C) configuration with reduced clearance to the separatrix does not appear to have a significant influence on the outer midplane separatrix and pedestal parameters when mapped to T e,ot , although conditions at the inner midplane could not be assessed.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗