Search NASA⌕ Search

Engineering topics

Guest, S. H.

Publications and source records attributed to Guest, S. H..

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Experimental study of damping of graphite epoxy composite material of the Space Telescope truss system

The truss system of the Hubble Space Telescope is made of graphite epoxy tubes and beams that have very low material damping. This paper describes a systematic experimental evaluation of the damping capacity of the graphite epoxy material used in the telescope truss system. The damping capacity of the composite material was measured both under normal and elevated temperatures in atmospheric conditions and in vacuum. Both free decay and steady state methods were used to measure the damping ratio of different specimens under different boundary conditions. A method that involves an iterative least-squares curve-fitting technique for the measured frequency response data has been developed to improve the accuracy of the damping ratio estimation. A unique experimental setup was developed to measure the damping of the material in a vacuum chamber. It was found that outgassing (moisture desorption) has little effect on the damping of the specimen. On the other hand, it was observed that temperature has a significant effect on both the damping and resonance frequencies of the specimen.

Rao, M. D.↗
NASA NTRS1985

Experimental evaluation of damping of graphite fiber composites

An investigation is described that was conducted to measure the damping of graphite fiber composites such as are to be used on the Hubble Space Telescope. The measurements were made on a composite cylinder under normal atmospheric conditions and in a vacuum chamber with varying thermal conditions. Such composites can outgas under vacuum conditions and this emission of trapped gases may have some influence on the material damping. Some results are presented for the damping coefficient measured under normal atmospheric conditions for a graphite fiber composite. The experimental damping data thus obtained were compared with the least square estimate obtained through a statistical analysis. The statistical analysis was based on a linear mathematical model consisting of a spring in parallel with a dashpot. It is observed that the discrepancy in the damping ratio between logarithmic decrement result and the least square fit is less than 6 percent for all the different tests made on the composite cylinder. Signal-to-noise ratio was maintained to be greater than 10.

Rao, M. D.↗
NASA NTRS1984

A correlation of scale model and flight aeroacoustic data for the Space Shuttle vehicle

A correlation is presented between aeroacoustic data acquired in the early Space Shuttle flights and in the various scale model tests from which the Shuttle vibroacoustic design environments were derived. These are the external acoustic data on the vehicle elements at liftoff, during the transonic and maximum dynamic pressure period of ascent flight, and during spent SRB reentry. The maximum external acoustic environment on the Shuttle elements in a given 1/3-octave frequency band comes from one of these critical flight regimes. The data correlation is seen to be good, testifying to adequate scale model measurement and test techniques. Some of the more salient features of the scale model test programs are described.

Dougherty, N. S.↗
NASA NTRS1982

Method and apparatus for suppressing ignition overpressure in solid rocket propulsion systems

The transient overpressure wave produced upon ignition of a solid rocket booster is suppressed by providing within the launch platform, a plurality of pipes and spray heads disposed around the periphery of the exhaust gas plume near its upper end and spraying water into the upper end of the plume during ignition. A large amount of water, preferably equivalent in mass of exhaust products being ejected, is sprayed into the plume in a direction generally perpendicular to plume flow.

Guest, S. H.↗
NASA NTRS1981

Propulsion system ignition overpressure for the Space Shuttle

Liquid and solid rocket motor propulsion systems create an overpressure wave during ignition, caused by the accelerating gas particles pushing against or displacing the air contained in the launch pad or launch facility and by the afterburning of the fuel-rich gases. This wave behaves as a blast or shock wave characterized by a positive triangular-shaped first pulse and a negative half-sine wave second pulse. The pulse travels up the space vehicle and has the potential of either overloading individual elements or exciting overall vehicle dynamics. The latter effect results from the phasing difference of the wave from one side of the vehicle to the other. This overpressure phasing, or delta P environment, because of its frequency content as well as amplitude, becomes a design driver for certain panels (e.g., thermal shields) and payloads for the Space Shuttle. The history of overpressure effects on the Space Shuttle, the basic overpressure phenomenon, Space Shuttle overpressure environment, scale model overpressure testing, and techniques for suppressing the overpressure environments are considered.

Ryan, R. S.↗
NASA NTRS1976

Space Shuttle noise suppression concepts for the Eastern Test Range

The basic objectives of the Space Shuttle noise suppression program for the Eastern Test Range were the definition of the acoustic environment of the Shuttle and the adjacent ground plane for both on-pad and liftoff conditions and the definition of realistic noise suppression techniques and modification of the launch facility that could reduce engine noise associated with supersonic flow. Scaling considerations for acoustic model testing based on the principle of dynamic similarity are detailed. Suppression approaches are described with emphasis placed on barriers and shields: exhaust flow trench covers, solid dividers between the SSME and SRB exhaust flows and a crossed pipe water injection system over the SSME exhaust flow trench. Graphs are presented summarizing noise data gathered for various noise sources and using different suppression approaches.

Guest, S. H.↗
NASA NTRS1974

Direct measurement of sound sources in air jets using the crossed beam correlation technique

Properties of density fluctuations were measured in the turbulent regions of a 2.54 cm air jet, at M = 0.7, 1.0 and 1.94. After calibration tests, it was found that the absorption of infrared radiation at 4.3 microns by the naturally present quantities of carbon-dioxide in air was directly proportional to the air density if a sufficiently wide bandpass (0.08 microns) was used. Moreover, regions of the band could be selected that adequately discriminated against temperature variations. The cross-correlation of two such beams intersecting in the jet gave a measure of the local properties at the intersection point. A derivation is presented relating the local density correlation function to the self and shear generated noise in the far field of the jet. The measured correlations are used to predict the axial distribution of source strengths and the spectrum of noise due to a unit volume of turbulence.

Damkevala, R. J.↗
NASA NTRS1972

Structural damage claims resulting from acoustic environments developed during static test firing of rocket engines

During static testing of multi-million pound thrust rocket engines areas adjacent to the test site have been subjected to the noise generated by rocket engines. Structural damage claims and subjective complaints were filed by those who alleged that the noise levels were excessive. The statistical analysis of these claims and complaints which were filed during these rocket engine development programs led to the determination of a relationship between claims and overall sound pressure level. Community exposure criteria are then assessed based on what can be considered allowable acoustic environments from large rocket engines.

Guest, S. H.↗