Engineering topics

Guidos, Mike

Publications and source records attributed to Guidos, Mike.

6 records

NASA NTRS2012

Transient Side Load Analysis of Out-of-Round Film-Cooled Nozzle Extensions

There was interest in understanding the impact of out-of-round nozzle extension on the nozzle side load during transient startup operations. The out-of-round nozzle extension could be the result of asymmetric internal stresses, deformation induced by previous tests, and asymmetric loads induced by hardware attached to the nozzle. The objective of this study was therefore to computationally investigate the effect of out-of-round nozzle extension on the nozzle side loads during an engine startup transient. The rocket engine studied encompasses a regeneratively cooled chamber and nozzle, along with a film cooled nozzle extension. The computational methodology is based on an unstructured-grid, pressure-based computational fluid dynamics formulation, and transient inlet boundary flow properties derived from an engine system simulation. Six three-dimensional cases were performed with the out-of-roundness achieved by three different degrees of ovalization, elongated on lateral y and z axes: one slightly out-of-round, one more out-of-round, and one significantly out-of-round. The results show that the separation line jump was the primary source of the peak side loads. Comparing to the peak side load of the perfectly round nozzle, the peak side loads increased for the slightly and more ovalized nozzle extensions, and either increased or decreased for the two significantly ovalized nozzle extensions. A theory based on the counteraction of the flow destabilizing effect of an exacerbated asymmetrical flow caused by a lower degree of ovalization, and the flow stabilizing effect of a more symmetrical flow, created also by ovalization, is presented to explain the observations obtained in this effort.

Wang, Ten-See↗

NASA NTRS2010

Transient Three-Dimensional Side Load Analysis of Out-of-Round Film Cooled Nozzles

The objective of this study is to investigate the effect of nozzle out-of-roundness on the transient startup side loads. The out-of-roundness could be the result of asymmetric loads induced by hardware attached to the nozzle, asymmetric internal stresses induced by previous tests and/or deformation, such as creep, from previous tests. The rocket engine studied encompasses a regeneratively cooled thrust chamber and a film cooled nozzle extension with film coolant distributed from a turbine exhaust manifold. The computational methodology is based on an unstructured-grid, pressure-based computational fluid dynamics formulation, and a transient inlet history based on an engine system simulation. Transient startup computations were performed with the out-of-roundness achieved by four degrees of ovalization of the nozzle: one perfectly round, one slightly out-of-round, one more out-of-round, and one significantly out-of-round. The computed side load physics caused by the nozzle out-of-roundness and its effect on nozzle side load are reported and discussed.

Wang, Ten-See↗

NASA NTRS2010

Transient Three-Dimensional Side Load Analysis of Out-of-Round Film Cooled Nozzles

The objective of this study is to investigate the effect of nozzle out-of-roundness on the transient startup side loads at a high altitude, with an anchored computational methodology. The out-of-roundness could be the result of asymmetric loads induced by hardware attached to the nozzle, asymmetric internal stresses induced by previous tests, and deformation, such as creep, from previous tests. The rocket engine studied encompasses a regeneratively cooled thrust chamber and a film cooled nozzle extension with film coolant distributed from a turbine exhaust manifold. The computational methodology is based on an unstructured-grid, pressure-based computational fluid dynamics formulation, and a transient inlet history based on an engine system simulation. Transient startup computations were performed with the out-of-roundness achieved by four different degrees of ovalization: one perfectly round, one slightly out-of-round, one more out-of-round, and one significantly out-of-round. The results show that the separation-line-jump is the peak side load physics for the round, slightly our-of-round, and more out-of-round cases, and the peak side load increases as the degree of out-of-roundness increases. For the significantly out-of-round nozzle, however, the peak side load reduces to comparable to that of the round nozzle and the separation line jump is not the peak side load physics. The counter-intuitive result of the significantly out-of-round case is found to be related to a side force reduction mechanism that splits the effect of the separation-line-jump into two parts, not only in the circumferential direction and most importantly in time.

Wang, Ten-See↗

NASA NTRS2008

Transient Three-Dimensional Side Load Analysis of a Film Cooled Nozzle

Transient three-dimensional numerical investigations on the side load physics for an engine encompassing a film cooled nozzle extension and a regeneratively cooled thrust chamber, were performed. The objectives of this study are to identify the three-dimensional side load physics and to compute the associated aerodynamic side load using an anchored computational methodology. The computational methodology is based on an unstructured-grid, pressure-based computational fluid dynamics formulation, and a transient inlet history based on an engine system simulation. Ultimately, the computational results will be provided to the nozzle designers for estimating of effect of the peak side load on the nozzle structure. Computations simulating engine startup at ambient pressures corresponding to sea level and three high altitudes were performed. In addition, computations for both engine startup and shutdown transients were also performed for a stub nozzle, operating at sea level. For engine with the full nozzle extension, computational result shows starting up at sea level, the peak side load occurs when the lambda shock steps into the turbine exhaust flow, while the side load caused by the transition from free-shock separation to restricted-shock separation comes at second; and the side loads decreasing rapidly and progressively as the ambient pressure decreases. For the stub nozzle operating at sea level, the computed side loads during both startup and shutdown becomes very small due to the much reduced flow area.

Wang, Ten-See↗

NASA NTRS2003

Transient Simulation of the Integrated Powerhead Demonstrator (IPD) Rocket Engine

The IPD rocket engine is the product of a joint Air Force/NASA program to demonstrate the concept of a full-flow staged combustion power cycle. In this type of rocket engine cycle, both the entire fuel flow and the entire oxidizer flow are combusted in one of two pre-bumers and used to drive two turbopumps, thus utilizing the flow work of the total propellant flow. The basis of the IPD engine program relies on integrating newly developed and pre-existing hardware to demonstrate the component and material technologies to make this concept feasible, while simultaneously saving development time and costs. To provide insight to the project team and contractors during engine development and test phases, the engine system was modeled at MSFC using the Rocket Engine Transient Simulation (ROCETS) software to analyze system performance and determine component integration issues. The ROCETS software is used extensively a MSFC to perform steady-state power-balances and transient simulations of thermodynamic power and general fluid systems. The software is favored for its capability to solve large systems of non-linear equations, its librarie of fluid properties and flow devices, its flexibility to modify existing code to improve the physics-derived approximations of real fluid thermodynamic behavior, and the ability to add unique system constraints. The purpose of this paper is to present the methodology used to model the IPD engine system, detail the pitfalls encountered with the software, and explain the approximations made to more accurately represent engine component and fluid behavior. Engine system performance output from the model will be presented and explained in comparison with real fluid and component behavior.

Guidos, Mike↗

NASA NTRS2001

Future Modeling Needs in Pulse Detonation Rocket Engine Design

This paper presents a performance model rocket engine design that takes advantage of pulse detonation to generate thrust. The contents include: 1) Introduction to the Pulse Detonation Rocket Engine (PDRE); 2) PDRE modeling issues and options; 3) Discussion of the PDRE Performance Workshop held at Marshall Space Flight Center; and 4) Identify needs involving an open performance model for Pulse Detonation Rocket Engines. This paper is in viewgraph form.

Meade, Brian↗