Search NASA⌕ Search

Engineering topics

Guillon, Olivier

Publications and source records attributed to Guillon, Olivier.

Thermal stability and coalescence dynamics of exsolved metal nanoparticles at charged perovskite surfaces

Exsolution reactions enable the synthesis of oxide-supported metal nanoparticles, which are desirable as catalysts in green energy conversion technologies. It is crucial to precisely tailor the nanoparticle characteristics to optimize the catalysts’ functionality, and to maintain the catalytic performance under operation conditions. We use chemical (co)-doping to modify the defect chemistry of exsolution-active perovskite oxides and examine its influence on the mass transfer kinetics of Ni dopants towards the oxide surface and on the subsequent coalescence behavior of the exsolved nanoparticles during a continuous thermal reduction treatment. Nanoparticles that exsolve at the surface of the acceptor-type fast-oxygen-ion-conductor SrTi 0.95 Ni 0.05 O 3–δ (STNi) show a high surface mobility leading to a very low thermal stability compared to nanoparticles that exsolve at the surface of donor-type SrTi 0.9 Nb 0.05 Ni 0.05 O 3–δ (STNNi). Our analysis indicates that the low thermal stability of exsolved nanoparticles at the acceptor-doped perovskite surface is linked to a high oxygen vacancy concentration at the nanoparticle-oxide interface. For catalysts that require fast oxygen exchange kinetics, exsolution synthesis routes in dry hydrogen conditions may hence lead to accelerated degradation, while humid reaction conditions may mitigate this failure mechanism.

25 ENERGY STORAGE↗

Optimizing the Composite Cathode Microstructure in All‐Solid‐State Batteries by Structure‐Resolved Simulations

Abstract All‐solid‐state batteries are considered as an enabler for applications requiring high energy and power density. However, they still fall short of their theoretical potential due to various limitations. One issue is poor charge transport kinetics resulting from both material inherit limitations and non‐optimized design. Therefore, a better understanding of the relevant properties of the cathode microstructure is necessary to improve cell performance. In this article, we identify optimization potentials of the composite cathode by structure‐resolved electrochemical 3D‐simulations. In our simulation study, we investigate the influence of cathode active material fraction, density, particle size, and active material properties on cell performance. Special focus is set on the impact of grain boundaries on the cathode design. Based on our simulation results, we can predict target values for cell manufacturing and reveal promising optimization strategies for an improved cathode design.

25 ENERGY STORAGE↗

Improving the W Coating Uniformity by a COMSOL Model-Based CVD Parameter Study for Denser W f /W Composites

Tungsten (W) has the unique combination of excellent thermal properties, low sputter yield, low hydrogen retention, and acceptable activation. Therefore, W is presently the main candidate for the first wall and armor material for future fusion devices. However, its intrinsic brittleness and its embrittlement during operation bears the risk of a sudden and catastrophic component failure. As a countermeasure, tungsten fiber-reinforced tungsten (W f /W) composites exhibiting extrinsic toughening are being developed. A possible W f /W production route is chemical vapor deposition (CVD) by reducing WF 6 with H 2 on heated W fabrics. The challenge here is that the growing CVD-W can seal gaseous domains leading to strength reducing pores. In previous work, CVD models for W f /W synthesis were developed with COMSOL Multiphysics and validated experimentally. In the present article, these models were applied to conduct a parameter study to optimize the coating uniformity, the relative density, the WF 6 demand, and the process time. A low temperature and a low total pressure increase the process time, but in return lead to very uniform W layers at the micro and macro scales and thus to an optimized relative density of the W f /W composite. High H 2 and low WF 6 gas flow rates lead to a slightly shorter process time and an improved coating uniformity as long as WF 6 is not depleted, which can be avoided by applying the presented reactor model.

36 MATERIALS SCIENCE↗

Calcium-Iron Oxide as Energy Storage Medium in Rechargeable Oxide Batteries

Rechargeable oxide batteries (ROB) comprise a regenerative solid oxide cell (rSOC) and a storage medium for oxygen ions. A sealed ROB avoids pumping loss, heat loss, and gas purity expenses in comparison with conventional rSOC. However, the iron oxide base storage medium degrades during charging–discharging cycles. In comparison, CaFe 3 O 5 has improved cyclability and a high reversible oxygen storage capacity of 22.3 mol%. In this paper, we analyzed the redox mechanism of this compound. After a solid-state synthesis of CaFe 3 O 5 , we verified the phase composition and studied the redox reaction by means of X-ray diffraction, Mössbauer spectrometry, and scanning electron microscopy. Finally, results show a great potential to operate the battery with this storage material during multiple charging–discharging cycles.

25 ENERGY STORAGE↗

Influence of Microstructure and Surface Activation of Dual-Phase Membrane Ce 0.8 Gd 0.2 O 2-δ -FeCo 2 O 4 on Oxygen Permeation

In dual-phase oxygen transport membranes we noticed that there is fast-growing interest in research for oxyfuel combustion process application. One such potential candidate is CGO-FCO (60wt% Ce 0.8 Gd 0.2 O 2-δ -40wt% FeCo 2 O4) identified to provide good oxygen permeation flux with substantial stability in harsh atmosphere. Dense CGO-FCO membranes of 1mm thickness were fabricated by sintering dry pellets pressed from powders synthesized by one-pot method (modified Pechini process) at 1200 degrees C for 10h. Microstructure analysis indicates presence of a third orthorhombic perovskite phase in the sintered composite. We also identified that the spinel phase tends to form an oxygen deficient phase at the grain boundary of spinel and CGO phases. Surface exchange limitation of the membranes was overcome by La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3-δ (LSCF) porous layer coating over the composite. Moreover, the oxygen permeation flux of the CGO-FCO screen printed with a porous layer of 10mthick LSCF is 0.11mL/cm 2 per minute at 850 degrees C with argon as sweep and air as feed gas at the rates of 50 and 250mL/min.

36 MATERIALS SCIENCE↗