Search NASA⌕ Search

Engineering topics

Gullikson, E. M.

Publications and source records attributed to Gullikson, E. M..

Nanometer flat blazed x-ray gratings using ion beam figure correction

With the development of nanometer accuracy stitching interferometry, ion beam figuring (IBF) of x-ray mirrors can now be achieved with unprecedented performance. However, the process of producing x-ray diffraction gratings on these surfaces may degrade the figure quality due to process errors introduced during the ruling of the grating grooves. To address this challenge, we have investigated the post-production correction of gratings using IBF, where stitching interferometry is used to provide in-process feedback. A concern with ion beam correction in this case is that ions will induce enough surface mobility of atoms to cause smoothing of the grating structure and degradation of diffraction efficiency. In this study we found however that it is possible to achieve a nanometer-level planarity of the global grating surface with IBF, while preserving the grating structure. The preservation was so good, that we could not detect a change in the diffraction efficiency after ion beam correction. This is of major importance in achieving ultra-high spectral resolution, and the preservation of brightness for coherent x-ray beams.

36 MATERIALS SCIENCE↗

6000 lines/mm blazed grating for a high-resolution x-ray spectrometer

We have designed and fabricated a high groove density blazed grating for a Resonant Inelastic X-ray Scattering spectrometer for the new Qerlin beamline at the Advanced Light Source (ALS) synchrotron facility. The gratings were fabricated using a set of nanofabrication techniques including e-beam lithography, nanoimprint, plasma etch, and anisotropic wet etching. Two gratings with groove density of 6000 lines/mm and 3000 lines/mm and optimized for operation in the 1st and 2nd negative diffraction order respectively were fabricated and tested. We report on fabrication details and characterization of the gratings at beamline 6.3.2 of the ALS.

36 MATERIALS SCIENCE↗

Highly efficient ultra-low blaze angle multilayer grating

We have developed an advanced process for blaze angle reduction of x-ray gratings for the soft, tender, and EUV spectral ranges. The process is based on planarization of an anisotropically etched Si blazed grating followed by a chemically selective plasma etch. This provides a way to adjust the blaze angle to any lower value with high accuracy. Here we demonstrate the reduction of the blaze angle to an extremely low value of 0.04°±0.004°. For a 100 lines/mm grating with a Mo/Si multilayer coating, the grating exhibits diffraction efficiency of 58% in the 1 st diffraction order at a wavelength of 13.3 nm. This technique will be applicable to a wide range of uses of high efficiency gratings for synchrotron sources, as well as for Free Electron Lasers (FEL).

42 ENGINEERING↗

Probing single-unit-cell resolved electronic structure modulations in oxide superlattices with standing-wave photoemission

Control of structural coupling at complex-oxide interfaces is a powerful platform for creating ultrathin layers with electronic and magnetic properties unattainable in the bulk. Yet, with the capability to design and control the electronic structure of such buried layers and interfaces at a unit-cell level, a new challenge emerges to be able to probe these engineered emergent phenomena with depth-dependent atomic resolution as well as element- and orbital selectivity. In this work, we utilize a combination of core-level and valence-band soft x-ray standing-wave photoemission spectroscopy, in conjunction with scanning transmission electron microscopy, to probe the depth-dependent and single-unit-cell resolved electronic structure of an isovalent manganite superlattice [Eu 0.7 Sr 0.3 MnO 3 /La 0.7 Sr 0.3 MnO 3 ]×15 wherein the electronic-structural properties are intentionally modulated with depth via engineered oxygen octahedra rotations/tilts and A-site displacements. Our unit-cell resolved measurements reveal significant transformations in the local chemical and electronic valence-band states, which are consistent with the layer-resolved first-principles theoretical calculations, hence opening the door for future depth-resolved studies of a wide variety of heteroengineered material systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Innovative diffraction gratings for high-resolution resonant inelastic soft x-ray scattering spectroscopy

High-resolution Resonant Inelastic X-ray Scattering (RIXS) requires diffraction gratings with very exacting characteristics. The gratings should provide both very high dispersion and high efficiency which are conflicting requirements and extremely challenging to satisfy in the soft x-ray region for a traditional grazing incidence geometry. To achieve high dispersion one should increase the groove density of a grating; this however results in a diffraction angle beyond the critical angle range and results in drastic efficiency loss. The problem can be solved by use of multilayer coated blazed gratings (MBG). In this work we have investigated the diffraction characteristics of MBGs via numerical simulations and have developed a procedure for optimization of grating design for a multiplexed high resolution imaging spectrometer for RIXS spectroscopy to be built in sector 6 at the Advanced Light Source (ALS). We found that highest diffraction efficiency can be achieved for gratings optimized for 4{sup th} or 5{sup th} order operation. Fabrication of such gratings is an extremely challenging technological problem. We present a first experimental prototype of these gratings and report its performance. High order and high line density gratings have the potential to be a revolutionary new optical element that should have great impact in the area of soft x-ray RIXS.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Fabrication and characterization of Sb/B4C multilayer mirrors for soft X-rays

Structure characterization of Sb/B 4 C multilayers for soft X-ray optics with a layers thickness from 0.5 nm to 7 nm is reported for the first time. Sb/B 4 C coatings were manufactured via magnetron sputtering. Amorphous and crystalline phases of the layers and the multilayer structure parameters were characterized with the X-ray diffraction data and the TEM data. The Sb/B 4 C multilayers demonstrated long term stability of their parameters and performances. The reached value of the reflectance of the Sb/B 4 C multilayers is 19–28% measured at the near-normal incidence in the wavelength range of 6.64–8.5 nm. The influence of reduced Sb density on the reflectivity is discussed.

36 MATERIALS SCIENCE↗

High-peak-power surface high-harmonic generation at extreme ultra-violet wavelengths from a tape

Solid-based surface high-harmonic generation from a tape is experimentally studied. By operating at mildly relativistic normalized laser strengths a{sub 0}≲0.2, harmonics up to the 17th order are efficiently produced in the coherent wake emission (CWE) regime. CWE pulse properties, such as divergence, energy, conversion efficiency, and spectrum, are investigated for various tape materials and drive laser conditions. A clear correlation between surface roughness and harmonic beam divergence is found. At the measured pulse properties for the 15th harmonic (conversion efficiency ∼6.5×10{sup −7}, divergence ∼7−15 mrad), the 100-mJ-level drive laser produces several MWs of extreme ultra-violet pulses. The spooling tape configuration enables multi-Hz operation over thousands of shots, making this source attractive as a seed to the few-Hz laser-plasma-accelerator-driven free-electron laser (FEL). Models indicate that these CWE pulses with MW level powers are sufficient for seed-induced bunching and FEL gain.

36 MATERIALS SCIENCE↗

Ultra-high efficiency multilayer blazed gratings through deposition kinetic control

Diffraction efficiency of multilayer coated blazed gratings (MBG) strongly depends on the perfection of the saw-tooth-shaped layers in the overall composite structure. Growth of multilayers on saw-tooth substrates should be carefully optimized in order to reduce groove profile distortion and at the same time to avoid significant roughening of multilayer interfaces. In this work we report on a new way to optimize growth of sputter-deposited Mo/Si multilayers on saw-tooth substrates through variation of the sputtering gas pressure. Lastly, a new record for diffraction efficiency of 44% was achieved for a optimized MBG with groove density of 5250 lines /mm at the wavelength of 13.1 nm.

36 MATERIALS SCIENCE↗

Optical constants from mirror reflectivities measured at synchrotrons

Improved mirror reflectivity measurement techniques have been introduced to permit more accurate determinations of optical constants delta and beta in the complex index of refraction n = 1 - delta - i(beta) over the energy range 50 to 5000 eV. When the density has been determined by X-ray or other means, one can calculate the real and imaginary parts, f-prime and f-double prime, of the complex atomic scattering factor f = f(o) + f-prime + if-double prime from delta and beta. Preliminary results are given for the Ni LIII edge around 852 eV, and the Au M edge region from 2150 to 3500 eV. Since these are the first experimental evaluations of delta for these element edges, they are compared with appropriate reservations to semiempirical tabulations. There is much potential for this technique applied to synchrotron sources.

Blake, R. L.↗