Search NASA⌕ Search

Engineering topics

Gunning, Brendan P.

Publications and source records attributed to Gunning, Brendan P..

Using machine learning with optical profilometry for GaN wafer screening

Abstract To improve the manufacturing process of GaN wafers, inexpensive wafer screening techniques are required to both provide feedback to the manufacturing process and prevent fabrication on low quality or defective wafers, thus reducing costs resulting from wasted processing effort. Many of the wafer scale characterization techniques—including optical profilometry—produce difficult to interpret results, while models using classical programming techniques require laborious translation of the human-generated data interpretation methodology. Alternatively, machine learning techniques are effective at producing such models if sufficient data is available. For this research project, we fabricated over 6000 vertical PiN GaN diodes across 10 wafers. Using low resolution wafer scale optical profilometry data taken before fabrication, we successfully trained four different machine learning models. All models predict device pass and fail with 70–75% accuracy, and the wafer yield can be predicted within 15% error on the majority of wafers.

36 MATERIALS SCIENCE↗

Demonstration of >6.0-kV Breakdown Voltage in Large Area Vertical GaN p-n Diodes With Step-Etched Junction Termination Extensions

Vertical gallium nitride (GaN) p-n diodes have garnered significant interest for use in power electronics where high-voltage blocking and high-power efficiency are of concern. In this article, we detail the growth and fabrication methods used to develop a large area (1 mm 2 ) vertical GaN p-n diode capable of a 6.0-kV breakdown. We also demonstrate a large area diode with a forward pulsed current of 3.5 A, an 8.3-mΩ$\cdot$cm 2 differential specific ON-resistance, and a 5.3-kV reverse breakdown. In addition, we report on a smaller area diode (0.063 mm 2 ) that is capable of 6.4-kV breakdown with a differential specific ON-resistance of 10.2 mΩ$\cdot$cm 2 , when accounting for current spreading through the drift region at a 45° angle. Finally, the demonstration of avalanche breakdown is shown for a 0.063-mm 2 diode with a room temperature breakdown of 5.6 kV. In this work, these results were achieved via epitaxial growth of a 50-μm drift region with a very low carrier concentration of <1×10 15 cm –3 and a carefully designed four-zone junction termination extension.

42 ENGINEERING↗

A discussion on various experimental methods of impact ionization coefficient measurement in GaN

Impact ionization coefficients play a critical role in semiconductors. In addition to silicon, silicon carbide and gallium nitride are important semiconductors that are being seen more as mainstream semiconductor technologies. As a reflection of the maturity of these semiconductors, predictive modeling has become essential to device and circuit designers, and impact ionization coefficients play a key role here. Recently, several studies have measured impact ionization coefficients. We dedicated the first part of our study to comparing three experimental methods to estimate impact ionization coefficients in GaN, which are all based on photomultiplication but feature characteristic differences. The first method inserts an InGaN hole-injection layer, the accuracy of which is challenged by the dominance of ionization in InGaN, leading to possible overestimation of the coefficients. The second method utilizes the Franz–Keldysh effect for hole injection but not for electrons, where the mixed injection of induced carriers would require a margin of error. The third method uses complementary p–n and n–p structures that have been at the basis of this estimation in Si and SiC and leans on the assumption of a constant electric field, and any deviation would require a margin of error. In the second part of our study, we evaluated the models using recent experimental data from diodes demonstrating avalanche breakdown.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Optimizing performance and yield of vertical GaN diodes using wafer scale optical techniques

Abstract To improve the manufacturing of vertical GaN devices for power electronics applications, the effects of defects in GaN substrates need to be better understood. Many non-destructive techniques including photoluminescence, Raman spectroscopy and optical profilometry, can be used to detect defects in the substrate and epitaxial layers. Raman spectroscopy was used to identify points of high crystal stress and non-uniform conductivity in a substrate, while optical profilometry was used to identify bumps and pits in a substrate which could cause catastrophic device failures. The effect of the defects was studied using vertical P-i-N diodes with a single zone junction termination extention (JTE) edge termination and isolation, which were formed via nitrogen implantation. Diodes were fabricated on and off of sample abnormalities to study their effects. From electrical measurements, it was discovered that the devices could consistently block voltages over 1000 V (near the theoretical value of the epitaxial layer design), and the forward bias behavior could consistently produce on-resistance below 2 mΩ cm 2 , which is an excellent value considering DC biasing was used and no substrate thinning was performed. It was found that high crystal stress increased the probability of device failure from 6 to 20%, while an inhomogeneous carrier concentration had little effect on reverse bias behavior, and slightly (~ 3%) increased the on-resistance (R on ). Optical profilometry was able to detect regions of high surface roughness, bumps, and pits; in which, the majority of the defects detected were benign. However a large bump in the termination region of the JTE or a deep pit can induce a low voltage catastrophic failure, and increased crystal stress detected by the Raman correlated to the optical profilometry with associated surface topography.

42 ENGINEERING↗

Fabrication and field emission properties of vertical, tapered GaN nanowires etched via phosphoric acid

The controlled fabrication of vertical, tapered, and high-aspect ratio GaN nanowires via a two-step top-down process consisting of an inductively coupled plasma reactive ion etch followed by a hot, 85% H 3 PO 4 crystallographic wet etch is explored. The vertical nanowires are oriented in the $[0001]$ direction and are bound by sidewalls comprising of $\{33\bar{6}2\}$ semipolar planes which are at a 12° angle from the [0001] axis. High temperature H3PO4 etching between 60 °C and 95 °C result in smooth semipolar faceting with no visible micro-faceting, whereas a 50 °C etch reveals a micro-faceted etch evolution. High-angle annular dark-field scanning transmission electron microscopy imaging confirms nanowire tip dimensions down to 8–12 nanometers. The activation energy associated with the etch process is 0.90 ± 0.09 eV, which is consistent with a reaction-rate limited dissolution process. The exposure of the $\{33\bar{6}2\}$ type planes is consistent with etching barrier index calculations. The field emission properties of the nanowires were investigated via a nanoprobe in a scanning electron microscope as well as by a vacuum field emission electron microscope. Finally, the measurements show a gap size dependent turn-on voltage, with a maximum current of 33 nA and turn-on field of 1.92 V nm -1 for a 50 nm gap, and uniform emission across the array.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Improved forward voltage and external quantum efficiency scaling in multi-active region III-nitride LEDs

Ultra-low voltage drop tunnel junctions (TJs) were utilized to enable multi-active region blue light emitting diodes (LEDs) with up to three active regions in a single device. The multi-active region blue LEDs were grown monolithically by metal-organic chemical vapor deposition (MOCVD) without growth interruption. This is the first demonstration of a MOCVD grown triple-junction LED. Optimized TJ design enabled near-ideal voltage and EQE scaling close to the number of junctions. Furthermore, this work demonstrates that with proper TJ design, improvements in wall-plug efficiency at high output power operation are possible by cascading multiple III-nitride based LEDs.

42 ENGINEERING↗

Ultralow Voltage GaN Vacuum Nanodiodes in Air

The III-nitride semiconductors have many attractive properties for field-emission vacuum electronics, including high thermal and chemical stability, low electron affinity, and high breakdown fields. In this work, we report top-down fabricated gallium nitride (GaN)-based nanoscale vacuum electron diodes operable in air, with record ultralow turn-on voltages down to ~0.24 V and stable high field-emission currents, tested up to several microamps for single-emitter devices. We leverage a scalable, top-down GaN nanofabrication method leading to damage-free and smooth surfaces. Gap-dependent and pressure-dependent studies provide new insights into the design of future, integrated nanogap vacuum electron devices. The results show promise for a new class of high-performance and robust, on-chip, III-nitride-based vacuum nanoelectronics operable in air or reduced vacuum.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

All-MOCVD-grown gallium nitride diodes with ultra-low resistance tunnel junctions

In this work, we carefully investigate three important effects including postgrowth activation annealing, delta (δ) dose and magnesium (Mg) buildup delay as well as experimentally demonstrate their influence on the electrical properties of GaN homojunction p–n diodes with a tunnel junction (TJ). The diodes were monolithically grown by metalorganic chemical vapor deposition (MOCVD) in a single growth step. By optimizing the annealing parameters for Mg activation, δ-dose for both donors and acceptors at TJ interfaces, and p + -GaN layer thickness, a significant improvement in tunneling properties is achieved. For the TJs embedded within the continuously-grown, all-MOCVD GaN diode structures, ultra-low voltage penalties of 158 mV and 490 mV are obtained at current densities of 20 A cm –2 and 100 A cm –2 , respectively. The diodes with the engineered TJs show a record-low differential resistivity of 1.6 × 10 –4 Ω cm 2 at 5 kA cm –2 .

42 ENGINEERING↗

A study on the impact of mid-gap defects on vertical GaN diodes

GaN is a favorable martial for future efficient high voltage power switches. GaN has not dominated the power electronics market due to immature substrate, homoepitaxial growth, and immature processing technology. Understanding the impact of the substrate and homoepitaxial growth on the device performance is crucial for boosting the performance of GaN. Here, we studied vertical GaN PiN diodes that were fabricated on non-homogenous Hydride Vapor Phase Epitaxy (HVPE) substrates from two different vendors. We show that defects which stemmed from growth techniques manifest themselves as leakage hubs. Different non-homogenous substrates showed different distribution of those defects spatially with the lesser quality substrates clustering those defects in clusters that causes pre-mature breakdown. Energetically these defects are mostly mid-gap around 1.8Ev with light emission spans from 450nm to 700nm. Photon emission spectrometry and hyperspectral electroluminescence were used to locate these defects spatially and energetically.

42 ENGINEERING↗

GaN/InGaN Blue Light-Emitting Diodes on Polycrystalline Molybdenum Metal Foils by Ion Beam-Assisted Deposition

Light-emitting diode (LED) arrays fabricated on a polycrystalline metal substrate are demonstrated using a novel technique that enables the growth of epitaxial metal-organic chemical vapor deposition (MOCVD) GaN layers on non-single-crystal substrates. Epitaxial GaN is deposited directly on metal foil using an intermediate ion beam-assisted deposition (IBAD) aligned layer. For a single 170 μm-diameter LED on the metal foil, electroluminescence (EL) spectrum shows a peak wavelength of ≈452 nm and a full width at half maximum (FWHM) of ≈24 nm. The current–voltage (I –V ) characteristics show a turn-on voltage of 3.7 V, a series resistance of 10 Ω. LEDs on metal show a relative external quantum efficiency (EQE) that is roughly 3× lower than that of similar LEDs fabricated on a sapphire substrate. Finally, InGaN LEDs on large-area non-single-crystal substrates such as metal foils enable large-area manufacturing, reducing production cost, and opening the door for new applications in lighting and displays.

36 MATERIALS SCIENCE↗

III-nitride photonic crystal emitters by selective photoelectrochemical etching of heterogeneous quantum well structures

We demonstrate a top-down fabrication strategy for creating a III-nitride hole array photonic crystal (PhC) with embedded quantum wells (QWs). Our photoelectrochemical (PEC) etching technique is highly bandgap selective, permitting the removal of QWs with well-defined indium (In) concentration. Room-temperature micro-photoluminescence (μ-PL) measurements confirm the removal of one multiple quantum well (MQW) while preserving a QW of differing In concentration. Moreover, PhC cavity resonances, wholly unobservable before, are present following PEC etching. Our results indicate an interesting route for creating III-nitride membranes with tailorable emission wavelengths. Our top-down fabrication approach offers exciting opportunities for III-nitride based light emitters.

36 MATERIALS SCIENCE↗

A review of the synthesis of reduced defect density In x Ga 1-x N for all indium compositions

A review of metal rich and nitrogen rich (N-rich), low-temperature grown In x Ga 1-x N is provided, focusing on two low-temperature approaches that have resulted in non-phase separated In x Ga 1-x N. The metal modulated epitaxy (MME) and N-rich, low temperature approaches to the reduction of defects in In x Ga 1-x N are described and are capable of growing In x Ga 1-x N throughout the miscibility gap. MME films remain smooth at all thicknesses but show device quality material primarily for x < 0.2 and x > 0.6. Low temperature, N-rich grown films show a critical thickness extend well beyond the theoretical values and results in slower relaxation through the 0.2 < x < 0.6 range most interesting for light emitters and solar cells. This reduced defect density results in improved optical emission, but due to increased roughening with increased thickness, low temperature, N-rich films are limited to thin layers. Future thick In x Ga 1-x N substrates are necessary to increase design freedom, as well as improve optoelectronic device performance. The initial results with films up to 800 nm are shown to display evidence of defect annihilation which could be promising for future thick optoelectronic templates and thick devices.

42 ENGINEERING↗

Phase degradation in B x Ga 1–x N films grown at low temperature by metalorganic vapor phase epitaxy

Using metalorganic vapor phase epitaxy, a comprehensive study of B x Ga 1-x N growth on GaN and AlN templates is described. BGaN growth at high-temperature and high-pressure results in rough surfaces and poor boron incorporation efficiency, while growth at low-temperature and low-pressure (750–900 °C and 20 Torr) using nitrogen carrier gas results in improved surface morphology and boron incorporation up to ~7.4% as determined by nuclear reaction analysis. However, further structural analysis by transmission electron microscopy and x-ray pole figures points to severe degradation of the high boron composition films, into a twinned cubic structure with a high density of stacking faults and little or no room temperature photoluminescence emission. Films with <1% triethylboron (TEB) flow show more intense, narrower x-ray diffraction peaks, near-band-edge photoluminescence emission at ~362 nm, and primarily wurtzite-phase structure in the x-ray pole figures. For films with >1% TEB flow, the crystal structure becomes dominated by the cubic phase. As a result, only when the TEB flow is zero (pure GaN), does the cubic phase entirely disappear from the x-ray pole figure, suggesting that under these growth conditions even very low boron compositions lead to mixed crystalline phases.

36 MATERIALS SCIENCE↗

Control of ion content and nitrogen species using a mixed chemistry plasma for GaN grown at extremely high growth rates >9 μm/h by plasma-assisted molecular beam epitaxy

Utilizing a modified nitrogen plasma source, plasma assisted molecular beam epitaxy (PAMBE) has been used to achieve higher growth rates in GaN. A higher conductance aperture plate, combined with higher nitrogen flow and added pumping capacity, resulted in dramatically increased growth rates up to 8.4 μm/h using 34 sccm of N{sub 2} while still maintaining acceptably low operating pressure. It was further discovered that argon could be added to the plasma gas to enhance growth rates up to 9.8 μm/h, which was achieved using 20 sccm of N{sub 2} and 7.7 sccm Ar flows at 600 W radio frequency power, for which the standard deviation of thickness was just 2% over a full 2 in. diameter wafer. A remote Langmuir style probe employing the flux gauge was used to indirectly measure the relative ion content in the plasma. The use of argon dilution at low plasma pressures resulted in a dramatic reduction of the plasma ion current by more than half, while high plasma pressures suppressed ion content regardless of plasma gas chemistry. Moreover, different trends are apparent for the molecular and atomic nitrogen species generated by varying pressure and nitrogen composition in the plasma. Argon dilution resulted in nearly an order of magnitude achievable growth rate range from 1 μm/h to nearly 10 μm/h. Even for films grown at more than 6 μm/h, the surface morphology remained smooth showing clear atomic steps with root mean square roughness less than 1 nm. Due to the low vapor pressure of Si, Ge was explored as an alternative n-type dopant for high growth rate applications. Electron concentrations from 2.2 × 10{sup 16} to 3.8 × 10{sup 19} cm{sup −3} were achieved in GaN using Ge doping, and unintentionally doped GaN films exhibited low background electron concentrations of just 1–2 × 10{sup 15} cm{sup −3}. The highest growth rates resulted in macroscopic surface features due to Ga cell spitting, which is an engineering challenge still to be addressed. Nonetheless, the dramatically enhanced growth rates demonstrate great promise for the future of III-nitride devices grown by PAMBE.

36 MATERIALS SCIENCE↗

Comprehensive study of the electronic and optical behavior of highly degenerate p-type Mg-doped GaN and AlGaN

The bulk and 2-dimensional (2D) electrical transport properties of heavily Mg-doped p-type GaN films grown on AlN buffer layers by Metal Modulated Epitaxy are explored. Distinctions are made between three primary p-type conduction mechanisms: traditional valence band conduction, impurity band conduction, and 2D conduction within a 2D hole gas at a hetero-interface. The bulk and 2D contributions to the overall carrier transport are identified and the relative contributions are found to vary strongly with growth conditions. Films grown with III/V ratio less than 1.5 exhibit high hole concentrations exceeding 2 × 10{sup 19} cm{sup −3} with effective acceptor activation energies of 51 meV. Films with III/V ratios greater than 1.5 exhibit lower overall hole concentrations and significant contributions from 2D transport at the hetero-interface. Films grown with III/V ratio of 1.2 and Mg concentrations exceeding 2 × 10{sup 20} cm{sup −3} show no detectable inversion domains or Mg precipitation. Highly Mg-doped p-GaN and p-AlGaN with Al fractions up to 27% similarly exhibit hole concentrations exceeding 2 × 10{sup 19} cm{sup −3}. The p-GaN and p-Al{sub 0.11}Ga{sub 0.89}N films show broad ultraviolet (UV) photoluminescence peaks, which intercept the valence band, supporting the presence of a Mg acceptor band. Finally, a multi-quantum-well light-emitting diode (LED) and p-i-n diode are grown, both of which demonstrate rectifying behavior with turn-on voltages of 3–3.5 V and series resistances of 6–10 Ω without the need for any post-metallization annealing. The LED exhibits violet-blue luminescence at 425 nm, while the p-i-n diode shows UV luminescence at 381 nm, and both devices still show substantial light emission even when submerged in liquid nitrogen at 77 K.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗