Engineering topics

Gunter, E. J.

Publications and source records attributed to Gunter, E. J..

At least 19 records

NASA NTRS1985

Changes of instability thresholds of rotor due to bearing misalignments

The influence of bearing misalignment upon the dynamic characteristics of statistically indeterminant rotor bearing systems is investigated. Both bearing loads and stability speed limits of a rotor may be changed significantly by magnitude and direction of bearing misalignment. The useful theory of short journal bearings is introduced and simple analytical expressions, governing the misalignment problem, are carried out. Polar plots for the bearing load capacities and stability maps, describing the speed limit in terms of misalignment, are presented. These plots can be used by the designer to estimate deviations between calculation and experimental data due to misalignment effects.

Springer, H.↗

NASA NTRS1983

Design study of magnetic eddy-current vibration suppression dampers for application to cryogenic turbomachinery

Cryogenic turbomachinery used to pump high pressure fuel (liquid H2) and oxidizer (liquid O2) to the main engines of the Space Shuttle have experienced rotor instabilities. Subsynchronous whirl, an extremely destructive instability, has caused bearing failures and severe rubs in the seals. These failures have resulted in premature engine shutdowns or, in many instances, have limited the power level to which the turbopumps could be operated. The feasibility of using an eddy current type of damping mechanism for the Space Shuttle Main Engine is outlined.

Gunter, E. J.↗

NASA NTRS1983

Influence of unbalance on the nonlinear dynamical response and stability of flexible rotor-bearing systems

In this paper, some of the effects of unbalance on the nonlinear response and stability of flexible rotor-bearing systems is presented from both a theoretical and experimental standpoint. In a linear system, operating above its stability threshold, the amplitude of motion grows exponentially with time and the orbits become unbounded. In an actual system, this is not necessarily the case. The actual amplitudes of motion may be bounded due to various nonlinear effects in the system. These nonlinear effects cause limit cycles of motion. Nonlinear effects are inherent in fluid film bearings and seals. Other contributors to nonlinear effects are shafts, couplings and foundations. In addition to affecting the threshold of stability, the nonlinear effects can cause jump phenomena to occur at not only the critical speeds, but also at stability onset or restabilization speeds.

Gunter, E. J.↗

NASA NTRS1981

A study of the modal truncation error in the component mode analysis of a dual-rotor system

In the component mode synthesis method, the equation of motion in the generalized coordinates is built upon the undamped eigenvalue data of the component structures. Error is inevitable when truncated modes are used. In this paper, two modal truncation schemes were evaluated with regard to the critical speed, stability, and unbalance response of a two-spool gas turbine engine. The numbers of modes required to yield acceptable accuracy in these cases were determined. Guidelines for modal truncation were derived from these results.

Li, D. F.↗

NASA NTRS1981

Component mode synthesis of large rotor systems

A scheme is presented for calculating the vibrations of large multi-component flexible rotor systems based on the component mode synthesis method. It is shown that, by a modal expansion of the elastic interconnecting elements, the system modal equation can be conveniently constructed from the undamped eigen representations of the component subsystems. The capability of the component mode method is demonstrated in two examples: a transient simulation of a two-spool gas turbine engine equipped with a squeeze-film damper; and an unbalance response analysis of the Space Shuttle Main Engine oxygen turbopump in which the dynamics of the rotor and the housing are both considered.

Li, D. F.↗

NASA NTRS1981

Unbalance response of a two spool gas turbine engine with squeeze film bearings

This paper presents a dynamic analysis of a two-spool gas turbine helicopter engine incorporating intershaft rolling element bearings between the gas generator and power turbine rotors. The analysis includes the nonlinear effects of a squeeze film bearing incorporated on the gas generator rotor. The analysis includes critical speeds and forced response of the system and indicates that substantial dynamic loads may be imposed on the intershaft bearings and main bearing supports with an improperly designed squeeze film bearing. A comparison of theoretical and experimental gas generator rotor response is presented illustrating the nonlinear characteristics of the squeeze film bearing. It was found that large intershaft bearing forces may occur even though the engine is not operating at a resonant condition.

Gunter, E. J.↗

NASA NTRS1981

Experimental measurements of the Space Shuttle main engine fuel and oxygen turbopump vibration characteristics

The vibration characteristics of the SSME (Space Shuttle main engine) are dealt with. The Space Shuttle engine consists of a main rocket nozzle and attached to it are high pressure fuel and oxygen pumps. Various vibration problems have been encountered with both the hydrogen and oxygen pumps. The vibration spectrum of the hydrogen and oxygen pumps has been analyzed by various techniques using synchronous tracking filters and FFT analyzers. The experimental data has been correlated to theoretical predictions of resonance frequencies.

Gunter, E. J.↗

NASA NTRS1980

Rotor transient analysis

Undamped modes approximate dynamic behavior of rotors and bearings. Application of modal analysis to uncouple equations of motion simplifies stability, steady-state unbalance response, and transient response analysis of system; nonlinear stability is predicted from calculated frequency spectra. Analysis provides designers with complete information without involving large-scale computational costs. Programs are written in FORTRAN IV for use on CDC 6600 computer.

Allaire, P. E.↗

NASA NTRS1980

Stabilization of aerodynamically excited turbomachinery with hydrodynamic journal bearings and supports

A method of analyzing the first mode stability and unbalance response of multimass flexible rotors is presented whereby the multimass system is modeled as an equivalent single mass modal model including the effects of rotor flexibility, general linearized hydrodynamic journal bearings, squeeze film bearing supports and rotor aerodynamic cross coupling. Expressions for optimum bearing and support damping are presented for both stability and unbalance response. The method is intended to be used as a preliminary design tool to quickly ascertain the effects of bearing and support changes on rotor-bearing system performance.

Barrett, L. E.↗

NASA NTRS1978

Dynamics of short eccentric plain seals with high axial Reynolds number

Plain seals with high axial flow rates produce large stiffness and damping coefficients that can help stabilize high-speed rotating machinery. When the shaft is eccentric in the seal, a Bernoulli effect low-pressure region occurs on the large-clearance side of the shaft. A fluid-restoring force tends to center the shaft and reduce vibrations. This work extends the previous theory for short plain centered seals to large eccentricities using a perturbation analysis. Surface roughness effects are also included. An analysis of seals used in the Space Shuttle main engine hydrogen fuel turbopump indicates the desirability of plain seals over the labyrinth type. Experimental results confirm this.

Allaire, P. E.↗

NASA NTRS1978

Dynamic analysis of flexible rotor-bearing systems using a modal approach

The generalized dynamic equations of motion were obtained by the direct stiffness method for multimass flexible rotor-bearing systems. The direct solution of the equations of motion is illustrated on a simple 3-mass system. For complex rotor-bearing systems, the direct solution of the equations becomes very difficult. The transformation of the equations of motion into modal coordinates can greatly simplify the computation for the solution. The use of undamped and damped system mode shapes in the transformation are discussed. A set of undamped critical speed modes is used to transform the equations of motion into a set of coupled modal equations of motion. A rapid procedure for computing stability, steady state unbalance response, and transient response of the rotor-bearing system is presented. Examples of the application of this modal approach are presented. The dynamics of the system is further investigated with frequency spectrum analysis of the transient response.

Choy, K. C.↗

NASA NTRS1978

Modal analysis of turborotors using planar modes - Theory

The generalized dynamic equations of motion have been obtained by the direct stiffness method for multimass flexible rotor bearing systems including the effects of gyroscopic moments, disk skew, and rotor acceleration. A set of undamped critical speed mode shapes calculated from the average horizontal and vertical bearing stiffness is used to transform the equations of motion into a set of coupled modal equations of motion. The modal equations are coupled by the generalized bearing coefficients and the gyroscopic moments. An analysis using only undamped critical speeds or decoupled modal analysis assuming proportional damping may lead to erroneous results. This paper presents a rapid method of calculating rotor resonance speeds with their corresponding amplification factors, stability and unbalance response of turborotors. Examples of the application of this modal approach are presented and results are compared to those of other methods such as matrix transfer analysis.

Gunter, E. J.↗

NASA NTRS1978

Fast Fourier transform analysis of rotor-bearing systems

Nonlinear transient analysis of rotor-bearing systems is becoming increasingly important in the analysis of modern-day rotating machinery to model such phenomena as oil film whirl. This paper develops an analysis technique incorporating modal analysis and fast Fourier transform techniques to analyze rotors with residual shaft bow and realistic nonlinear bearings. The technique is demonstrated on single-mass and three-mass rotor examples. Comparisons of the theoretical results with experimental data give excellent agreement.

Choy, K. C.↗

NASA NTRS1975

Design of a squeeze-film damper for a multi-mass flexible rotor

A single mass flexible rotor analysis was used to optimize the stiffness and damping of a flexible support for a symmetric five-mass rotor. The flexible support attenuates the rotor motions and forces transmitted to the support bearings when the rotor operates through and above its first bending critical speed. An oil squeeze-film damper was designed based on short bearing lubrication theory. The damper design was verified by an unbalance response computer program. Rotor amplitudes were reduced by a factor of 16 and loads reduced by a factor of 36 compared with the same rotor on rigid bearing supports.

Cunningham, R. E.↗

NASA NTRS1975

Design and application of squeeze film dampers for turbomachinery stabilization

The steady-state transient response of the squeeze film damper bearing was investigated. Both the steady-state and transient equations for the hydrodynamic bearing forces are derived; the steady-state equations were used to determine the damper equivalent stiffness and damping coefficients. These coefficients are used to find the damper configuration which will provide the optimum support characteristics based on a stability analysis of the rotor-bearing system. The effects of end seals and cavitated fluid film are included. The transient analysis of rotor-bearing systems was conducted by coupling the damping and rotor equations and integrating forward in time. The effects of unbalance, cavitation, and retainer springs are included. Methods of determining the stability of a rotor-bearing system under the influence of aerodynamic forces and internal shaft friction are discussed.

Gunter, E. J.↗

NASA NTRS1975

Stability and transient motion of a plain journal mounted in flexible damped supports

Results are presented for an extensive study of the influence of damped flexible supports on the stability-threshold speed of a symmetric rotor mounted in nonlinear fluid-film bearings. A stability analysis is conducted by applying the Routh criteria and calculating the damped eigenvalues of the system. Stability maps are given in dimensionless form for a range of support stiffness, damping, and mass ratios. The effect of rotor imbalance on the stability of rotor systems is examined, and it is shown that time transient orbits of shaft and support motions clearly indicate their dynamic behavior for both stable and unstable operating speeds. Simple design criteria are proposed for choosing the support stiffness and damping on the basis of rotor weight and journal clearance to promote optimum stability. It is concluded that the use of a flexible damped support system may increase the stability threshold of a plain journal bearing and that damper supports should promote smoother and quieter machine operation by suppressing oil whirl and attenuating unbalanced rotational forces.

Kirk, R. G.↗

NASA NTRS1975

Steady-state and transient analysis of a squeeze film damper bearing for rotor stability

A study of the steady-state and transient response of the squeeze film damper bearing is presented. Both the steady-state and transient equations for the hydrodynamic bearing forces are derived. The bearing equivalent stiffness and damping coefficients are determined by steady-state equations. These coefficients are used to find the bearing configuration which will provide the optimum support characteristics based on a stability analysis of the rotor-bearing system. The transient analysis of rotor-bearing systems is performed by coupling the bearing and journal equations and integrating forward in time. The effects of unbalance, cavitation, and retainer springs are included in the analysis. Methods of determining the stability of a rotor-bearing system under the influence of aerodynamic forces and internal shaft friction are discussed with emphasis on solving the system characteristic frequency equation and on producing stability maps. It is shown that for optimum stability and low force transmissability the squeeze bearing should operate at an eccentricity ratio epsilon 0.4.

Barrett, L. E.↗

NASA NTRS1973

Nonlinear transient analysis of multi-mass flexible rotors - theory and applications

The equations of motion necessary to compute the transient response of multi-mass flexible rotors are formulated to include unbalance, rotor acceleration, and flexible damped nonlinear bearing stations. A method of calculating the unbalance response of flexible rotors from a modified Myklestad-Prohl technique is discussed in connection with the method of solution for the transient response. Several special cases of simplified rotor-bearing systems are presented and analyzed for steady-state response, stability, and transient behavior. These simplified rotor models produce extensive design information necessary to insure stable performance to elastic mounted rotor-bearing systems under varying levels and forms of excitation. The nonlinear journal bearing force expressions derived from the short bearing approximation are utilized in the study of the stability and transient response of the floating bush squeeze damper support system. Both rigid and flexible rotor models are studied, and results indicate that the stability of flexible rotors supported by journal bearings can be greatly improved by the use of squeeze damper supports. Results from linearized stability studies of flexible rotors indicate that a tuned support system can greatly improve the performance of the units from the standpoint of unbalanced response and impact loading. Extensive stability and design charts may be readily produced for given rotor specifications by the computer codes presented in this analysis.

Kirk, R. G.↗