Search NASA⌕ Search

Engineering topics

Guo, J.

Publications and source records attributed to Guo, J..

At least 37 records · Page 2

Design of the Electron Ion Collider Electron Storage Ring SRF cavity

The Electron Ion Collider (EIC) under construction at Brookhaven National Laboratory is a high luminosity collider as the next major research facility for the nuclear physics community. Among the numerous RF subsystems in the EIC, the electron storage ring (ESR) fundamental RF cavities system is one of the most challenging. This system will handle a high beam current of up to 2.5A and replenish up to 10MW of beam power losses from synchrotron radiation and HOM. Variable coupling is required in the cavities due to the wide range of required total RF voltage and beam current combinations. In this paper, we will present the status of the design and future plans.

Guo, J.↗

Accelerator commissioning and rare isotope identification at the Facility for Rare Isotope Beams

In 2008, Michigan State University was selected to establish the Facility for Rare Isotope Beams (FRIB). Construction of the FRIB accelerator was completed in January 2022. Phased accelerator commissioning with heavy ion beams started in 2017 with the normal-conducting ion source and radio-frequency quadrupole. In April 2021, the full FRIB driver linear accelerator (linac) was commissioned, with heavy ion beams accelerated to energies above 200 MeV/nucleon by 324 superconducting radiofrequency (SRF) resonators operating at 2 K and 4 K with liquid-helium cooling. Further, in preparation for high-power operation, a liquid lithium charge stripper was commissioned with heavy ion beams up to uranium-238, followed by the simultaneous acceleration of multiple-charge-state heavy ion beams to energies above 200 MeV/nucleon. In December 2021, selenium-84 was produced with the FRIB target using a krypton-86 primary beam, demonstrating FRIB’s capability for scientific discovery.

07 ISOTOPE AND RADIATION SOURCES↗

Structure of the thermal boundary layer in turbulent channel flows at transcritical conditions

Enhanced fluctuations, steep gradients, and intensified heat transfer are characteristics of wall-bounded turbulence at transcritical conditions. Although such conditions are prevalent in numerous technical applications, the structure of the thermal boundary layer under realistic density gradients and heating conditions remains poorly understood. Specifically, statistical descriptions of the temperature field in such flows are provided inconsistently using existing models. To address this issue, direct numerical simulations are performed by considering fully developed transcritical turbulent channel flow at pressure and temperature conditions that cause density changes of a factor of up to $O(20)$ between the hot and cold walls. As a consequence of the proximity of the Widom line to the hot wall, significant asymmetries are observed when comparing regions near the cold wall and near the hot wall. Previous transformations that attempt to collapse the near-wall mean temperature profiles among different cases to a single curve are examined. By addressing model deficiencies of these transformations, a formulation for an improved mean temperature transformation is proposed, with appropriate considerations for real fluid effects that involve strong variations in thermodynamic quantities. Our proposed transformation is shown to perform well in collapsing the slope of the logarithmic region to a single universal value with reduced uncertainty. Coupled with a predictive framework to estimate the non-universal shift parameter of the logarithmic region using a priori information, our transformation provides an analytic profile to model the near-wall mean temperature. These results thus provide a framework to guide the development of models for wall-bounded transcritical turbulence.

42 ENGINEERING↗

The Design of a High Charge Polarized Preinjector for the Electron-Ion Collider

The design of the electron pre-injector of the Electron-Ion Collider (EIC) project to generate 4 x 7 nC bunch has been advancing to meet the requirements for injection into the Rapid Cycling Synchrotron (RCS). The major challenges are high charge transport and achieving small energy spread from 3 GHz traveling-wave plate(TWP). The designed preinjector includes the polarized electron source, bunching section, TWP Linac, zigzag phase space manipulation and spin rotator. In this report, we will discuss the RF frequency selection and the way to reduce energy spread down to 0.2% by longitudinal phase space manipulate. We will also report the results of beamline simulation using space charge code and the conceptual design of spin rotator.

Wang, E.↗

RF Harmonic Kicker R&D Demonstration and Its Application to the RCS Injection of the EIC

The Rapid Cycling Synchrotron (RCS) of the Electron-Ion Collider (EIC) at Brookhaven National Laboratory (BNL) is an accelerating component of the electron injection complex, which provides polarized electrons in electron-ion collisions in the main Electron Storage Ring (ESR). We present the injection scheme into the RCS based on an ultra-fast harmonic kicker, whose "five odd-harmonic modes" prototype was developed in the context of the Jefferson Lab EIC (JLEIC) conceptual design. In its early stage of R&D, the sharp (~3 ns width) waveform construction, beam dynamics, and pulsed power operation with short ramping time (~10 us) will be discussed together with the fabrication work of the JLEIC prototype.

Park, G. -T.↗

The RCS Design Status for the Electron Ion Collider

The design of the Electron-Ion Collider Rapid Cycling Synchrotron (RCS) to be constructed at Brookhaven National Laboratory is advancing to meet the injection requirements for the Electron Storage Ring (ESR). Over the past year activities are focused on developing the approach to inject two 28 nC bunches every second, up from the original design of one 10nC bunch every second. The solution requires several key changes concerning the injection and extraction kickers, charge accumulation via bunch merging and a carefully calibrated RF acceleration profile to match the longitudinal emittance required by the ESR.

Ranjbar, V. H.↗

Low-Energy Cooling for Electron Ion Collider

Luminosity parameters at the highest hadron energy in the Electron Ion Collider (EIC) require a proton beam with a small vertical emittance. Such a small emittance can be obtained using the technique of electron cooling, by pre-cooling of the proton bunches at an injection energy of 23:8 GeV. After pre-cooling, the proton bunches are accelerated to the maximum energy for collisions. Once at the top energy, such proton bunches can be refilled frequently to maintain a high average luminosity, or, alternatively, cooling at the top energy could be provided with relaxed requirements of just counteracting the emittance growth due to Intra-Beam Scattering (IBS) and thus maintaining the luminosity close to its initial peak value. Presently, several schemes of cooling at the top energy of 275 GeV are being considered with the goal to maintain the initial proton beam parameters, thus relying on pre-cooling at the low energy to obtain such initial parameters of proton bunches. For the lowest proton collision energy of 41 GeV in the EIC, there is a need for an electron cooler which counteracts the beam emittance growth due to IBS. This can be achieved by the same electron cooler which is used for cooling of protons at 23.8 GeV. In this case, we assume the electron cooler rst pre-cools protons at an injection energy of 23.8 GeV and then, after acceleration, cools the 41 GeV protons, counteracting IBS and maintaining the beam emittances. In this report, we summarize a feasibility study of an electron cooler that would be needed to cool protons at 23.8 GeV to obtain a small vertical emittance, as well as to counteract beam growth due to IBS for collisions at 41 GeV. The traditional electron cooling system employed at a typical low-energy cooler is based on an electron beam generated with an electrostatic electron gun in DC operating mode, immersed in a longitudinal magnetic field. To cool protons at 23.8 and 41 GeV, electron beam energies of 13.0 and 22.3MeV, respectively, are required. Due to the technical limitations of static high-voltage acceleration, these beam energies require RF acceleration of a pulsed electron beam. Electron cooling using RF-accelerated electron bunches was recently successfully commissioned in RHIC, allowing us to consider such an approach for EIC low-energy electron cooling.

43 PARTICLE ACCELERATORS↗

MAGNETIZED ELECTRON SOURCE FOR JLEIC COOLER

Magnetized bunched-beam electron cooling is a critical part of the Jefferson Lab Electron Ion Collider (JLEIC). Strong cooling of ion beams will be accomplished inside a cooling solenoid where the ions co-propagate with an electron beam generated from a source immersed in a magnetic field. This contribution describes the production and characterization of magnetized electron beam using a compact 300 kV DC high voltage photogun and bialkali-antimonide photocathodes. Beam magnetization was studied using a diagnostic beamline that includes viewer screens for measuring the shearing angle of the electron beamlet passing through a narrow upstream slit. Correlated beam emittance with magnetic field (0-1.5 kG)at the photocathode was measured for various laser spot sizes. Measurements of photocathode lifetime were carried out at different magnetized electron beam currents up to 28 mA and high bunch charge up to 0.7 nano-Coulomb was demonstrated.

Suleiman, R.↗

HIGH CURRENT HIGH CHARGE MAGNETIZED AND BUNCHED ELEC-TRON BEAM FROM A DC PHOTOGUN FOR JLEIC COOLER

A high current, high charge magnetized electron beam-line was developed for fast and efficient cooling of ion beams for the proposed Jefferson Lab Electron Ion Col-lider (JLEIC). In this paper, we describe recent achieve-ments that include the generation of picosecond-bunch magnetized beams at average currents up to 28 mA with exceptionally long photocathode lifetime, and independent demonstrations of magnetized beam with high bunch charge up to 700 pC at 10s of kHz repetition rates. In addition, a detailed description of an extremely stable and reliable fiber-based drive laser system that employs a gain-switched master oscillator is presented. These ac-complishments mark important steps toward demonstrat-ing the feasibility of a technically challenging JLEIC cooler design using magnetized beams

Adderley, P.↗

Pulsed Operation of CEBAF for JLEIC Injection

JLab Electron Ion Collider (JLEIC) is planning to use the recently upgraded 12 GeV CEBAF 1497 MHz SRF CW recirculating linac as a full-energy injector for the electron collider ring. The JLEIC electron injection requires 3-4µs long bunch trains with a 20-400ms spacing in between, resulting in uneven beam loading for the CW CEBAF. With the high beam current in JLEIC collider rings, the low duty factor of injection also requires to a very high pulsed beam current from CEBAF, exacerbating the transient beam loading issue. In this paper, we will present CEBAFs detailed pulsed operation scheme for JLEIC injection, as well as some experimental results at CEBAF.

Guo, J.↗

Design of a low-cost, compact SRF accelerator for flue gas and wastewater treatment

The treatment of flue gases from power plants and municipal or industrial wastewater using electron beam irradiation technology has been successfully demonstrated in small-scale pilot plants. The beam energy requirement is rather modest, of the order of few MeV, however the adoption of the technology at an industrial scale requires the availability of a high beam power, of the order of 1 MW, in a cost effective way. In this report we present the design of a compact superconducting accelerator capable of delivering a cw electron beam with a current of 1 A and an energy of 1 MeV. The main components are an rf-gridded thermionic gun and a conduction cooled beta= 0.5 elliptical Nb3Sn cavity with dual coaxial power couplers. An engineering and cost analysis shows that the proposed design would result in a processing cost competitive with alternative treatment methods.

43 PARTICLE ACCELERATORS↗

Interplanetary Coronal Mass Ejection Observed at STEREO-A, Mars, Comet 67P/Churyumov-Gerasimenko, Saturn,and New Horizons En Route to Pluto: Comparison of Its Forbush Decreases at 1.4, 3.1, and 9.9 AU

We discuss observations of the journey throughout the Solar System of a large interplanetary coronal mass ejection (ICME) that was ejected at the Sun on 14 October 2014. The ICME hit Mars on 17 October, as observed by the Mars Express, Mars Atmosphere and Volatile EvolutioN Mission (MAVEN), Mars Odyssey, and Mars Science Laboratory (MSL) missions, 44 h before the encounter of the planet with the Siding-Spring comet, for which the space weather context is provided. It reached comet 67P/Churyumov-Gerasimenko, which was perfectly aligned with the Sun and Mars at 3.1 AU, as observed by Rosetta on 22 October. The ICME was also detected by STEREO-A on 16 October at 1 AU, and by Cassini in the solar wind around Saturn on the 12 November at 9.9 AU. Fortuitously, the New Horizons spacecraft was also aligned with the direction of the ICME at 31.6 AU. We investigate whether this ICME has a nonambiguous signature at New Horizons. A potential detection of this ICME by Voyager 2 at 110-111 AU is also discussed. The multispacecraft observations allow the derivation of certain properties of the ICME, such as its large angular extension of at least 116deg, its speed as a function of distance, and its magnetic field structure at four locations from 1 to 10 AU. Observations of the speed data allow two different solar wind propagation models to be validated. Finally, we compare the Forbush decreases (transient decreases followed by gradual recoveries in the galactic cosmic ray intensity) due to the passage of this ICME at Mars, comet 67P, and Saturn.

Witasse, O.↗