Search NASA⌕ Search

Engineering topics

Guo, Qianying

Publications and source records attributed to Guo, Qianying.

13 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Reliability of Materials and Components for Solid Oxide Fuel Cells

Planar stack solid-oxide fuel cells (SOFCs) require seals that must operate reliably under demanding conditions for lifetimes of 40000 hours. This includes temperature fluctuations between 800°C and RT during on and off cycles, thermal stresses, oxidizing environments and chemical degradation to name a few. This comprehensive report provides results from long term testing of two commercially available multicomponent barium alkali silicate glasses: SCN and G6, chosen as sealing candidates. In this scope, the glass seals were deposited on YSZ and Al 2 O 3 substrates simulating electrolytes (Zrbased) and coatings (both zirconia and Al 2 O 3 ). The seal-substrate couples were subjected to 800°C under air and steam+H 2 +N 2 environments up to 40000 hours to test their integrity under real operating conditions. Extensive studies on the effects of exposure have been conducted over the span of testing at various time intervals. Within the context of characterization, mechanical properties such as density, roughness, thermal expansion and glass transition, viscosity and wettability behavior; and microstructural properties such as glass chemistries, defect formation (cracks and pores), phase transformations (devitrification) and glass-interface reactions are investigated. Results and discussions are provided with a focus on the degradation of the properties over long term interrupted testing.

30 DIRECT ENERGY CONVERSION↗
DOE OSTI2021

Evolution of the structure and chemical composition of the interface between multi-component silicate glasses and yttria-stabilized zirconia after 40,000 h exposure in air at 800 °C

The chemical and structural stability of two commercial multicomponent silicate glasses (SCN and G6) in contact with yttria-stabilized zirconia (YSZ) was investigated after exposure times of up to 40,000 h in air at 800 °C. With exposure time, interfacial layers develop at the SCN-YSZ and G6-YSZ interfaces, which were characterized in detail using both quantitative chemical analysis and atomic-resolution imaging. At the SCN-YSZ interface, a Ca-Ba-Si-O reaction phase was found to grow by diffusion control. In G6-YSZ, Raman spectroscopy and electron microscopy revealed a disorganized interfacial reaction later between G6 and YSZ, and the occurrence of cubic to tetragonal to monoclinic phase transformations in YSZ. Finally, this microstructural evolution is discussed in terms of devitrification resistance of glass and diffusion processes at interfaces.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Defect detection in atomic-resolution images via unsupervised learning with translational invariance

Abstract Crystallographic defects can now be routinely imaged at atomic resolution with aberration-corrected scanning transmission electron microscopy (STEM) at high speed, with the potential for vast volumes of data to be acquired in relatively short times or through autonomous experiments that can continue over very long periods. Automatic detection and classification of defects in the STEM images are needed in order to handle the data in an efficient way. However, like many other tasks related to object detection and identification in artificial intelligence, it is challenging to detect and identify defects from STEM images. Furthermore, it is difficult to deal with crystal structures that have many atoms and low symmetries. Previous methods used for defect detection and classification were based on supervised learning, which requires human-labeled data. In this work, we develop an approach for defect detection with unsupervised machine learning based on a one-class support vector machine (OCSVM). We introduce two schemes of image segmentation and data preprocessing, both of which involve taking the Patterson function of each segment as inputs. We demonstrate that this method can be applied to various defects, such as point and line defects in 2D materials and twin boundaries in 3D nanocrystals.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Analytical modeling of the evolution of the nonlinearity parameter of sensitized stainless steel

Austenitic stainless steels are subject to the precipitation of chromium carbides (M 23 C 6 ) during exposure to high temperatures, causing these alloys to be susceptible to intergranular corrosion due to chromium depletion along grain boundaries. The acoustic nonlinearity parameter, β, shows sensitivity to the formation of carbides in these alloys. The Thermo-Calc TC-PRISMA module was used to model the nucleation and growth of grain boundary M 23 C 6 carbides. The model was verified with scanning transmission electron microscopy analysis that allowed measurements of the grain boundary precipitates. The paper introduces a reduced-order model of the acoustic nonlinearity based on the formation of misfit dislocations at the interface of the grain boundary precipitate and matrix to explain the change in β during isothermal aging. Furthermore, a direct relationship between the radius of the M 23 C 6 grain boundary carbides and β was observed and verified with nonlinear ultrasound measurements on 304L and 316L stainless steels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

W-ZrC composites prepared by reactive melt infiltration of Zr 2 Cu alloy into binder jet 3D printed WC preforms

W-ZrC composites were successfully prepared by reactive melt infiltration (RMI) of stoichiometric and excess amounts of Zr 2 Cu into sintered and un-sintered WC preforms made from binder jet 3D printing. The focus of this work was to study the conversion of reactant powders and liquid infiltrant with varying preform density and infiltrant amount by controlling the processing time to reach high conversion yield while understanding the phase composition, microstructure, and hardness. To investigate the effect of time, the reactive melt infiltration was conducted at 1400 °C for 2, 4 and 8 h in a furnace with 96% Ar - 4% H2 gas atmosphere. The increase in reaction time from 2 to 8 h increased the W and W 2 C phase contents and decreased the ZrC phase content when using sintered WC preforms. Samples prepared from un-sintered WC preforms exhibited improved reactive melt infiltration compared to sintered samples, and there was no detectable W 2 C phase and nearly full consumption of WC. Similar to sintered WC samples, the content of W and ZrC phases increased with the increase in time from 2 to 8 h. The interfaces and phases at reaction interfaces were investigated using electron diffraction analysis and S/TEM-EDS to understand material stability; the phases were identified and consistent with XRD analysis. Additionally, there was no Cu present at the interfaces. Increasing the amount of infiltrant led to better reactive melt infiltration. In general, the hardness increased with reaction time and the highest Vickers hardness was found in the W-ZrC sample formed from sintered WC reacted with excess Zr 2 Cu. Finally, this research addresses the critical comparison of sintering and RMI time and shows that by using un-sintered samples for 8 h we are able to achieve W-ZrC composites with fewer undesired phases.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In situ indentation and high cycle tapping deformation responses in a nanolaminate crystalline/amorphous metal composite

The incorporation of nanostructured and amorphous metals into modern applications is reliant on the understanding of deformation and failure modes in constrained conditions. To study this, a 105 nm crystalline Cu/160 nm amorphous Cu 45 Zr 55 (at.%) multilayer structure was fabricated with the two crystalline layers sputter deposited between the top-middle-bottom amorphous layers and prepared to electron transparency. The multilayer was then in situ indented either under a single load to a depth of ~ 100 nm (max load of ~ 100 μN) or held at 20 μN and then repeatedly indented with an additional 5 μN up to 20,000 cycles in a transmission electron microscope to compare the deformation responses in the nanolaminate. For the single indentation test, the multilayer showed serrated load-displacement behavior upon initial indentation inductive of shear banding. Additionally, at an indentation depth of ~ 32 nm, the multilayer exhibited perfect plastic behavior and no strain hardening. Both indented and fatigue-indented films revealed diffraction contrast changes with deformation. Subsequent Automated Crystal Orientation Mapping (ACOM) measurements confirmed and quantified global texture changes in the crystalline layers with specifically identified grains revealing rotation. Using a finite element model, the in-plane displacement vectors under the indent mapped conditions where ACOM determined grain rotation was observed, indicating the stress flow induced grain rotation. Furthermore, the single indented Cu layers also exhibited evidence of deformation induced grain growth, which was not evident in the fatigue-indented Cu based multilayer. Finally, the single indented multilayer retained a significant plastic crater in the upper most amorphous layer that directly contacted the indenter; a negligible crater impression in the same region was observed in the fatigued tested multilayer. These differences are explained by the different loading methods, applied load, and deformation mechanisms experienced in the multilayers.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Stable and Catalytically Active Shape-Engineered Cerium Oxide Nanorods by Controlled Doping of Aluminum Cations

Shape-engineered nanocrystals (SENs) promise a better selectivity and a higher activity in catalytic reactions than the corresponding non-shape-engineered ones because of their larger specific surface areas and desirable crystal facets. However, often, it is challenging to apply SENs in practical catalytic applications at high reaction temperatures, where SENs deforms into more stable, less active nanoparticles. In this paper, we show that atomic layer deposition (ALD) of Al 2 O 3 at 200 °C can controllably dope Al cations into the shape-engineered CeO 2 nanorods (NRs) to not only increase their shape transition temperature from 400 °C to beyond 700 °C but also greatly increase their specific reversible oxygen storage capacity (srOSC). Furthermore, the substituted Al3+ ions impede the surface diffusion of Ce ions and therefore improve the thermal stability of CeO 2 NRs. These Al3+ dopants form -Al–O–Ce–O– clusters, which are new Ce species and can be reversibly reduced and oxidized at 500–700 °C. This low-temperature chemical doping method decouples the synthesis process of SENs from the doping process and maintains the shape of the SENs during the activation of dopants. This concept could be adopted to enable the applications of other SENs in challenging high-temperature environments.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗