Engineering topics

Gupta, A. K.

Publications and source records attributed to Gupta, A. K..

7 records

NASA NTRS2003

Characteristics of Gaseous Diffusion Flames with High Temperature Combustion Air in Microgravity

The characteristics of gaseous diffusion flames have been obtained using high temperature combustion air under microgravity conditions. The time resolved flame images under free fall microgravity conditions were obtained from the video images obtained. The tests results reported here were conducted using propane as the fuel and about 1000 C combustion air. The burner included a 0.686 mm diameter central fuel jet injected into the surrounding high temperature combustion air. The fuel jet exit Reynolds number was 63. Several measurements were taken at different air preheats and fuel jet exit Reynolds number. The resulting hybrid color flame was found to be blue at the base of the flame followed by a yellow color flame. The length and width of flame during the entire free fall conditions has been examined. Also the relative flame length and width for blue and yellow portion of the flame has been examined under microgravity conditions. The results show that the flame length decreases and width increases with high air preheats in microgravity condition. In microgravity conditions the flame length is larger with normal temperature combustion air than high temperature air.

Ghaderi, M.↗

NASA NTRS2001

Combustion of Gaseous Fuels with High Temperature Air in Normal- and Micro-gravity Conditions

The objective of this study is determine the effect of air preheat temperature on flame characteristics in normal and microgravity conditions. We have obtained qualitative (global flame features) and some quantitative information on the features of flames using high temperature combustion air under normal gravity conditions with propane and methane as the fuels. This data will be compared with the data under microgravity conditions. The specific focus under normal gravity conditions has been on determining the global flame features as well as the spatial distribution of OH, CH, and C2 from flames using high temperature combustion air at different equivalence ratio.

Wang, Y.↗

NASA NTRS1983

A three-stage power amplifier for a 20 GHz monolithic transmit module

Design, fabrication, and test results of a three-stage GaAs monolithic power amplifier covering the 17.7 to 20.2 GHz band are described. Intermediate results for single and two-stage amplifiers are also presented. The 1.5 x 3.1 millimeter three-stage amplifier chip has 15 dB gain from 16.5 to 20.2 GHz. Measured saturated output power is between +20 and +21 dBm with improvement expected from minor circuit and device changes.

Petersen, W. C.↗

NASA NTRS1983

A two-stage monolithic buffer amplifier for 20 GHz satellite communication

Design, fabrication, and test results of a two-stage GaAs monolithic buffer amplifier for 20 GHz satellite communication are described in this paper. A gain of 13 + or - 0.75 dB from 17.7 to 20.2 GHz was obtained from the 1.5 x 1.5 millimeter chip, which includes all necessary bias and dc blocking circuitry.

Petersen, W. C.↗

NASA NTRS1982

Flow aerodynamics modeling of an MHD swirl combustor - Calculations and experimental verification

This paper describes a computer code for calculating the flow dynamics of constant density flow in the second stage trumpet shaped nozzle section of a two stage MHD swirl combustor for application to a disk generator. The primitive pressure-velocity variable, finite difference computer code has been developed to allow the computation of inert nonreacting turbulent swirling flows in an axisymmetric MHD model swirl combustor. The method and program involve a staggered grid system for axial and radial velocities, and a line relaxation technique for efficient solution of the equations. Turbulence simulation is by way of a two-equation Kappa-epsilon model. The code produces as output the flowfield map of the nondimensional stream function, axial, and swirl velocity. Good agreement was obtained between the theoretical predictions and the qualitative experimental results. The best seed injector location for uniform seed distribution at combustor exit is with injector located centrally on the combustor axis at entrance to the second stage combustor.

Gupta, A. K.↗

NASA NTRS1982

Modeling parameter influences on MHD swirl combustion nozzle design

Attention is given to a research project which has the goal to develop a two-stage slagging gasifier-combustor in the form of a high-intensity combustor, taking into account a suitable aerodynamic design of the second stage nozzle which will prevent the separation of the boundary layer as the flow turns from axial to radial direction. The specific objectives of the present investigation are to test the effect of various second-stage nozzle geometries, flow rates, swirl number, and distribution in the first and second stages upon the corresponding flowfield in the second stage. Special emphasis is given to the avoidance of boundary layer separation as the flow turns from axial to radial direction into the MHD disk generator.

Lilley, D. G.↗

NASA NTRS1981

Flow aerodynamics modeling of an MHD swirl combustor - Calculations and experimental verification

The paper describes a computer code for calculating the flow dynamics of a constant-density flow in the second-stage trumpet shaped nozzle section of a two-stage MHD swirl combustor for application to a disk generator. The primitive pressure-velocity variable, finite-difference computer code has been developed for the computation of inert nonreacting turbulent swirling flows in an axisymmetric MHD model swirl combustor. The method and program involve a staggered grid system for axial and radial velocities, and a line relaxation technique for the efficient solution of the equations. The code produces as output the flow field map of the nondimensional stream function, axial and swirl velocity. It was found that the best location for seed injection to obtain a uniform distribution at the combustor exit is in the central location for seed injected at the entrance to the second stage combustor.

Gupta, A. K.↗