Engineering topics
Gupta, Ramesh
Publications and source records attributed to Gupta, Ramesh.
Low temperature superconductor and aligned high temperature superconductor magnetic dipole system and method for producing high magnetic fields
A dipole-magnet system and method for producing high-magnetic-fields, including an open-region located in a radially-central-region to allow particle-beam transport and other uses, low-temperature-superconducting-coils comprised of low-temperature-superconducting-wire located in radially-outward-regions to generate high magnetic-fields, high-temperature-superconducting-coils comprised of high-temperature-superconducting-tape located in radially-inward-regions to generate even higher magnetic-fields and to reduce erroneous fields, support-structures to support the coils against large Lorentz-forces, a liquid-helium-system to cool the coils, and electrical-contacts to allow electric-current into and out of the coils. The high-temperature-superconducting-tape may be comprised of bismuth-strontium-calcium-copper-oxide or rare-earth-metal, barium-copper-oxide (ReBCO) where the rare-earth-metal may be yttrium, samarium, neodymium, or gadolinium. Advantageously, alignment of the large-dimension of the rectangular-cross-section or curved-cross-section of the high-temperature-superconducting-tape with the high-magnetic-field minimizes unwanted erroneous magnetic fields. Alignment may be accomplished by proper positioning, tilting the high-temperature-superconducting-coils, forming the high-temperature-superconducting-coils into a curved-cross-section, placing nonconducting wedge-shaped-material between windings, placing nonconducting curved-and-wedge-shaped-material between windings, or by a combination of these techniques.
Development of an Accelerator-Quality High-Field Common-Coil Dipole Magnet
Explore the source record for details and available documents.
Development of Magnesium Diboride Superconducting Coils for Nuclear Physics Application
The primary objective of this project is to develop an affordable magnet technology at 10-25K and then take it to a level that it can be considered mature enough to be used in a real Nuclear Physics accelerator system. We believe that because of the lower cost of magnesium diboride (MgB2) as compared to the other HTS, it offers the best such chance. Once successfully demonstrated, this exciting and innovative technology could potentially revolutionize the field the same way the conventional superconducting NbTi magnets did several decades ago. MgB2 magnets could reduce the cost of ownership (capital +operation) while enhancing performance. Another innovation is the overall cooling scheme where the exhaust gas of an existing superconducting magnet cools the inner tube which conduction cools the MgB2 coils. In several instances during the upgrade of existing facilities or designing new facilities in the Nuclear Physics or High Energy Physics communities, it is found that magnets made neither with copper coils nor with conventional superconducting NbTi coils offer an acceptable solution. Whereas copper coils limit the performance of the machine and consume large amount of power, NbTi require 4 K cryogenic facilities. This is particularly applicable in those Nuclear Physics machines where the magnetic field requirements are rather modest. One such case has been found in the Relativistic Heavy Ion Collider (RHIC) at Brookhaven National Laboratory (BNL) where an e-lens system is under construction to increase RHIC luminosity. In this case, magnesium diboride (MgB2) operating at 10-25 K seems to offer an exciting and practical solution. The main objective in Phase II is to demonstrate the reliability and robustness of the MgB2 coil technology, so that it is ready for use in RHIC and other user facilities. We will do this by fabricating several MgB2 coils and by conducting an exhaustive series of lifetime cycle tests. The tests will involve about a thousand ramp-up and ramp-down cycles, about 20 over current or thermal-excursions hitting the quench limit and about 10 thermal cycles. Phase II will begin with a design modeling effort of the MgB2 coils for the e-lens system with enough detail so that the magnetic, thermal and stress requirements can be understood for the fabrication and testing of representative MgB2 coils. After the technology is proven in Phase II for reliability, we will propose to use this in Phase III to upgrade RHIC e-lens system for improved luminosity performance and expect that more applications will follow in other accelerator and medical facilities.
High Radiation Environment Nuclear Fragment Separator Magnet
Superconducting coils wound with HTS conductor can be used in magnets located in a high radiation environment. NbTi and Nb 3 Sn superconductors must operate at 4.5 K or below where removal of heat is less efficient. The HTS conductor can carry significant current at higher temperatures where the Carnot efficiency is significantly more favorable and where the coolant heat capacity is much larger. Using the HTS conductor the magnet can be operated at 40 K. This project examines the use of HTS conductor for the Michigan State University Facility For Rare Isotope Beams (FRIB) fragment separator dipole magnet which bends the beam by 30° and is located in a high radiation region that will not be easily accessible. Two of these magnets are needed to select the chosen isotope. There are a number of technical challenges to be addressed in the design of this magnet. The separator dipole is 2 m long and subtends a large angle. The magnet should keep a constant transverse field profile along its beam reference path. Winding coils with a curved inner segment is difficult as the conductor will tend to unwind during the process. In the Phase I project two approaches to winding the conductor were examined. The first was to wind the coils with curved sections on the inner and outer segments with the inner segment wound with negative curvature. The alternate approach was to use a straight segment on the inner segment to avoid negative curvature. In Phase I coils with a limited number of turns were successfully wound and tested at 77 K for both coil configurations. The Phase II program concentrated on the design, coil winding procedures, structural analysis, prototyping and testing of an HTS curved dipole coil at 40 K with a heat load representative of the radiation environment. One of the key criteria of the design of this magnet is to avoid the use of organic materials that would degrade rapidly in radiation. The Lorentz forces expected from the coils interacting with the magnetic field are large and in order minimize the deformation of the coils, mechanical support must be provided. Since the support structure cannot be made of organic materials with minimal thermal conductivity, an optimization was explored comparing the amount of coil deformation that can be tolerated and the amount of heat leakage that can be endured. A test coil containing 500 m of HTS was constructed to be tested at the 40 K operating temperature. The anticipated heat load was simulated with heater strips to demonstrate that the heat could be removed and that the coil can operate in a stable state. The FRIB project has decided that using HTS coils for this magnet was too risky considering their time and funding constraints and has opted for a more conservative approach with conventional coils. As an outcome of this STTR project, it is likely that HTS coils operating at higher temperatures will have beneficial applications for future accelerator projects.
Design, Construction and Testing of a Large Aperture High Field HTS SMES Coil
Explore the source record for details and available documents.
A hybrid HTS/LTS Superconductor Design for High-Field Accelerator Magnets
High magnetic fields approaching 25 T are needed for significant advances in the physics reach of colliders for high energy physics. Large Hadron Collider (LHC) at CERN needs very high field magnets for planned energy and luminosity upgrades. The envisioned Muon Collider needs such magnets in several areas of the machine. High Temperature Superconductors (HTS) currently offer the best chance of producing hybrid magnets for these applications because HTS has a significantly higher critical current density than any other superconductor at high fields.)
Magnet Coil Designs Using YBCO High Temperature Superconductor
Magnet coils built with the superconducting “cos θ” technology have proven extraordinarily popular, cost effective and reliable in modern particle accelerators. The term “cos θ” describes a coil design in which current conductors are placed on the surface of a cylindrical tube with more turns near the mid-plane and less near the pole proportional to the cosine of the angle measured from the mid-plane. Once this challenging technology is mastered, the design offers many options regarding cost, field intensity and quality, size of aperture, and multipole fields that are important to accelerator designers and builders for bending and controlling beam particles.
Development of Magnesium Diboride Superconducting Coils for Nuclear Physics Applications
In Phase I, BNL assisted Hyper Tech with appropriate modeling and magnet designs that were tailored to the current performance of 10-25 K MgB2 coils for RHIC. Hyper Tech conducted R&D to fabricate and test an MgB2 coil. A successful completion of Phase I has led to a Phase II where HyperTech and BNL has again teamed-up to utilize their expertise that will cumulate in an entire system which will undergo extended testing over a large number of power, quench and thermal cycles together with the field quality measurements and other rigorous evaluations to verify that the magnet performance and reliability is appropriate for use in a major Nuclear Physics facility consisting of superconducting magnets.
High Radiation Environment Nuclear Fragment Separator Magnet
Abstract not provided.
Heat load of a GaAs photocathode in an SRF electron gun
A great deal of effort has been made over the last decades to develop a better polarized electron source for high energy physics. Several laboratories operate DC guns with a gallium arsenide photocathode, which yield a highly polarized electron beam. However, the beam's emittance might well be improved by using a superconducting radio frequency (SRF) electron gun, which delivers beams of a higher brightness than that from DC guns because the field gradient at the cathode is higher. SRF guns with metal and CsTe cathodes have been tested successfully. To produce polarized electrons, a Gallium-Arsenide photo-cathode must be used: an experiment to do so in a superconducting RF gun is under way at BNL. Since a bulk gallium arsenide (GaAs) photocathode is normal conducting, a problem arises from the heat load stemming from the cathode. In this paper, we present our measurements of the electrical resistance of GaAs at cryogenic temperatures, a prediction of the heat load and verification by measuring the quality factor of the gun with and without the cathode at 2 K. We simulate heat generation and flow from the GaAs cathode using the ANSYS program. Finally, by following the findings with the heat load model, we designed and fabricated a new cathode holder (plug) to decrease the heat load from GaAs.