Engineering topics

H Q Yang

Publications and source records attributed to H Q Yang.

3 records

NASA NTRSDate not supplied

Slosh-Induced Ullage Collapse Validation by Computational Fluid Dynamics and Application to In-space Propellant Dynamics

Ullage collapse predictions made using Computational Fluid Dynamics (CFD) were validated then made for an in-space cryogenic propellant unsettling application. Ullage collapse is the decrease in propellant tank pressure due to cooling of the ullage gas, which can be significant for cryogenic propulsion systems. Vehicles may be developed that are robust to temperature and pressure changes caused by heat leaks, e.g., propellant tanks with high maximum operation pressures, technologies yielding active thermal conditioning, and systems with ample pressurant for conditioning. These methods are robust because additional mass, cost, and complexity are used to address cryogenic fluid management (CFM). As vehicles are optimized for increased payload capacity, tracking of events such as ullage collapse and self-pressurization in tanks will become increasingly important for propellant inventory calculations. Some ullage collapse events can be studied through ground experimentation, but propellant unsettling in and around in-space coast mission phases must be studied in the absence of an acceleration field. Computational Fluid Dynamics is a powerful tool to address this need, enabling prediction of complex physics prior to flight. Validation of the chosen CFD tool and modeling methodology was done using data from a previously conducted subscale slosh-induced ullage collapse ground test performed in part by the Japan Aerospace Exploration Agency (JAXA). A small tank was partially filled with liquid nitrogen and pressurized with gaseous nitrogen at various temperatures. The tank was oscillated laterally to induce high amplitude slosh dynamics resulting in wave breakup. Successful qualitative validation of slosh wave dynamics and quantitative validation of ullage collapse promoted confidence in extending ullage collapse predictions to a flight application. Mechanisms of ullage collapse caused by main engine cutoff while in-space were identified. Both slosh dynamics leading to engine shutdown and body dynamics following shutdown were shown to contribute to propellant unsettling and ullage collapse.

J M Brodnick↗

NASA NTRSDate not supplied

Validation of Ullage Collapse Due to Violent Lateral Slosh

Understanding the coupling between thermodynamics and propellant sloshing is important for cryogenic upper stages, especially during the lift-off phase and in missions including multiple engine restarts, as the fluid dynamic condition of the propellant is mainly influenced by various flight maneuvers. This paper describes the development and validation of a Volume of Fluid (VOF)-based CFD solver, Loci/STREAM-VOF, to the ullage collapse under violent later slosh conditions. Loci/STREAM-VOF is shown to be able to capture detailed slosh dynamics, including slosh frequency, non-linear slosh damping, and violent surface breakup due to forced acceleration. The comparison of surface shape and small drops formed during large amplitude slosh with experimental imagery shows excellent agreement throughout the sloshing period. Comparison of temperature histories in the ullage, at the gas-liquid interface, and inside liquid with the experiment conducted at JAXA also show very good agreement. The simulation points to a stratified temperature field inside the liquid near the interface, critical to the ullage pressure after the collapse. The predicted pressure collapse matches well with the experimental value due to sloshing. Parametric sensitivity studies suggest that high-fidelity Loci/STREM-VOF simulations can play an essential role in predicting the actual thermodynamics of ullage collapse when following the recommended simulation methodology.

H Q Yang↗

NASA NTRSDate not supplied

Validation of Cryogenic Propellant Tank Filling using Computational Fluid Dynamics Simulation

Validation of cryogenic propellant tank filling was performed using the Computational Fluid Dynamics (CFD) solver Loci/STREAM-VoF. The validation effort helped identify modeling methodologies that enable NASA to best support its partners in both launch pad and on-orbit filling operations. Data from liquid hydrogen ground tests filled via jet injection were used for the validation effort which include a sensitivity to initial tank wall temperature. Initially hot walls are expected to yield rapid evaporation and possibly boiling. A Volume of Fluid (VoF) methodology was used to capture the gas-liquid interface. Rapid breakup of the liquid jet was observed in simulation results as liquid evaporated and expanded. Inflowing liquid transitioned to a contiguous jet as tank temperatures decreased, gas pressure increased, and saturation conditions at the incoming liquid temperature were approached. The final phase of filling was distinguished by rapid gas pressure rise due to a higher rate of gas volume compression than condensation at the liquid surface. Key physics of propellant tank filling were captured in the computational predictions, and opportunities for added simulation robustness and efficiency in future modeling efforts were identified.

CFM↗