Engineering topics

Hall, D. W.

Publications and source records attributed to Hall, D. W..

8 records

NASA NTRS1991

Advanced aircraft for atmospheric research

The development of aircraft for high-altitude research is described in terms of program objectives and environmental, technological limitations, and the work on the Perseus A aircraft. The need for these advanced aircraft is proposed in relation to atmospheric science issues such as greenhouse trapping, the dynamics of tropical cyclones, and stratospheric ozone. The implications of the study on aircraft design requirements is addressed with attention given to the basic categories of high-altitude, long-range, long-duration, and nap-of-the-earth aircraft. A strategy is delineated for a platform that permits unique stratospheric measurements and is a step toward a more advanced aircraft. The goal of Perseus A is to carry scientific air sampling payloads weighing at least 50 kg to altitudes of more than 25 km. The airfoils are designed for low Reynolds numbers, the structural weight is very low, and the closed-cycle power plant runs on liquid oxygen.

Russell, P.↗

NASA NTRS1987

Carbon Dioxide Observational Platform System (CO-OPS), feasibility study

The Carbon Dioxide Observational Platform System (CO-OPS) is a near-space, geostationary, multi-user, unmanned microwave powered monitoring platform system. This systems engineering feasibility study addressed identified existing requirements such as: carbon dioxide observational data requirements, communications requirements, and eye-in-the-sky requirements of other groups like the Defense Department, the Forestry Service, and the Coast Guard. In addition, potential applications in: earth system science, space system sciences, and test and verification (satellite sensors and data management techniques) were considered. The eleven month effort is summarized. Past work and methods of gathering the required observational data were assessed and rough-order-of magnitude cost estimates have shown the CO-OPS system to be most cost effective (less than $30 million within a 10 year lifetime). It was also concluded that there are no technical, schedule, or obstacles that would prevent achieving the objectives of the total 5-year CO-OPS program.

Bouquet, D. L.↗

NASA NTRS1985

Mission analysis of solar powered aircraft

The effect of a real mission scenario on a solar powered airplane configuration which had been developed in previous work were assessed. The mission used was surveillance of crop conditions over a route from Phoenix to Tucson to Tombstone, Arizona. Appendices are attached which address the applicability of existing platforms and payloads to do this mission.

Hall, D. W.↗

NASA NTRS1984

Structural sizing of a solar powered aircraft

The development of sizing algorithms for very lightweight aircraft structure was studied. Three types of bracing schemes were analyzed and fully cantilevered strut bracing and wire bracing and scaling rules were determined. It is found that wire bracing provides the lightest wing structure for solar high altitude powered platforms.

Hall, D. W.↗

NASA NTRS1983

A Preliminary Study of Solar Powered Aircraft and Associated Power Trains

The feasibility of regeneratively powered solar high altitude powered platform (HAPP) remotely piloted vehicles was assessed. Those technologies which must be pursued to make long duration solar HAPPs feasible are recommended. A methodology which involved characterization and parametric analysis of roughly two dozen variables to determine vehicles capable of fulfilling the primary mission are defined. One of these vehicles was then conceptually designed. Variations of each major design parameter were investigated along with state-of-the-art changes in power train component capabilities. The midlatitude mission studied would be attainable by a solar HAPP if fuel cell, electrolyzer and photovoltaic technologies are pursued. Vehicles will be very large and have very lightweight structures in order to attain the combinations of altitude and duration required by the primary mission.

Hall, D. W.↗

NASA NTRS1980

A three-dimensional body-fitted coordinate system for flow field calculations on asymmetric nosetips

A three dimensional body-fitted coordinate system developed for use in the calculation of inviscid flows over ablated, asymmetric reentry vehicle nosetips is described. Because of the potential geometric asymmetries, no standard coordinate system (e.g., spherical, axisymmetric reference surface-normal) is capable of being closely aligned with the nosetip surface. To generate a 3-D, body-fitted coordinate system an analytic mapping procedure is applied that is conformal within each meridional plane of the nosetip; these transformations are then coupled circumferentially to yield a three dimensional coordinate system. The mappings used are defined in terms of hinge points, which are points selected to approximate the body contours in each meridional plane. The selection of appropriate hinge points was automated to facilitate the use of the resulting nosetip flow field code.

Hall, D. W.↗

NASA NTRS1979

Extended analytical study of the free-wing/free-trimmer concept

The free wing/free trimmer concept was analytically studied in order to: (1) compare the fore and aft trimmer configurations on the basis of equal lift capability, rather than equal area; (2) assess the influence of tip mounted aft trimmers, both free and fixed, on the lateral directional modes and turbulence responses; (3) examine the feasibility of using differential tip mounted trimmer deflection for lateral control; (4) determine the effects of independent fuselage attitude on the lateral directional behavior; and (5) estimate the influence of wing sweep on dynamic behavior and structural weight. Results indicate that the forward trimmer concept is feasible with the reduced size examined, but it remains inferior to the aft trimmer in every respect except structural weight. Differential motion of the aft trimmer is found to provide powerful lateral control; while the effect of fuselage deck angle is a reduction of the dutch roll damping ratio for nose-down attitudes.

Porter, R. F.↗

NASA NTRS1978

Analytical study of a free-wing/free-trimmer concept

The free-wing/free-trimmer is a NASA-Conceived extension of the free-wing concept intended to permit the use of high-lift flaps. Wing pitching moments are balanced by a smaller, external surface attached by a boom or equivalent structure. The external trimmer is, itself, a miniature free wing, and pitch control of the wing-trimmer assembly is effected through a trailing-edge control tab on the trimmer surface. The longitudinal behavior of representative small free-wing/free-trimmer aircraft was analyzed. Aft-mounted trimmer surfaces are found to be superior to forward trimmers, although the permissible trimmer moment arm is limited, in both cases, by adverse dynamic effects. Aft-trimmer configurations provide excellent gust alleviation and meet fundamental stick-fixed stability criteria while exceeding the lift capabilities of pure free-wing configurations.

Porter, R. F.↗