Search NASA⌕ Search

Engineering topics

Hallo, L

Publications and source records attributed to Hallo, L.

In-situ small-angle x-ray scattering study of nanoparticles in the plasma plume induced by pulsed laser irradiation of metallic targets

Small angle x-ray scattering was used to probe in-situ the formation of nanoparticles in the plasma plume generated by pulsed laser irradiation of a titanium metal surface under atmospheric conditions. The size and morphology of the nanoparticles were characterized as function of laser irradiance. Two families of nanoparticles were identified with sizes on the order of 10 and 70 nm, respectively. These results were confirmed by ex-situ transmission electron microscopy experiments.

36 MATERIALS SCIENCE↗

Laser plasma plume structure and dynamics in the ambient air: The early stage of expansion

Laser ablation plasma plume expanding into the ambient atmosphere may be an efficient way to produce nanoparticles. From that reason it would be interesting to study the properties of these laser induced plasmas formed under conditions that are known to be favorable for nanoparticles production. In general, plume behavior can be described as a two-stage process: a 'violent' plume expansion due to the absorption of the laser beam energy (during the laser pulse) followed by a fast adiabatic expansion in the ambient gas (after the end of the laser pulse). Plasma plume may last a few microseconds and may have densities 10{sup -6} times lower than the solid densities at temperatures close to the ambient temperature. Expansion of the plasma plume induced by the impact of a nanosecond laser beam ({lambda} 1064 nm) on the surface of metallic samples in the open air has been investigated by means of fast photography. Spatio-temporal evolution of the plume at the early stage of its expansion (first 330 ns) has been recorded. Structure and dynamics of the plasma plume have been investigated and compared to numerical simulations obtained with a hydro-code, as well as some scaling laws. In addition, measurements using different sample materials (Al, Fe, and Ti) have been performed in order to analyze the influence of target material on plume expansion.

36 MATERIALS SCIENCE↗

Surface structuring by ultrashort laser pulses: A review of photoionization models

Photoionization models have been introduced and compared in a three-dimensional code utilizing electromagnetic wave propagation in dielectric materials such as fused silica. Ionization rates are initially compared and matched to linear and circular polarizations. Then, they are implemented in the propagation code followed by some hydrodynamic simulations. Results on the structural and optical modifications have been compared with available experimental data. Experimental damage, ablation threshold, and a theoretical damage threshold criteria have been utilized to discriminate between the different models.

36 MATERIALS SCIENCE↗

The HiPER Experimental Road Map

WP10 is one of the working packages of the HiPER project and it has the goal of addressing, in a systematic and programmatic way, some of the key experimental uncertainties on the way towards fast ignition (and shock ignition) in a perspective of risk reduction, so to contribute to the definition of the basic characteristics of the HiPER project. The paper describes the key points contained in the short term HiPER experimental road map, as well as the results of two first experiments performed in 'HiPER dedicated time slots' in European Laser Facilities.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Toward a new nanoLIFT transfer process

The Laser Induced Forward Transfer (LIFT) is a direct-write technique used to print biological materials such as living cells or molecules. During the LIFT process, the biomaterial to be printed is deposited on a target submitted to a nanosecond laser shot, and the ejecta are collected onto a receiving substrate. Despite the several advantages of this technique (control of the propelled quantity, no spoiling of the substrate), it remains difficult to be employed due to the high sensitivity of its control parameters. Recently, Duocastella published some experimental results which exhibit the real-time jet formation process, under conditions similar to those present in the LIFT process. In the first Section, a typical experimental setup for LIFT process is presented. Then, simulations of Duocastella's and Guillemot's experiments are carried out to model the jet formation in water when irradiated by an ultraviolet nanosecond laser pulse. The 2D axisymmetric hydrodynamic code CHIC (Code d'Hydrodynamique et d'Implosion du CELIA) is used for these simulations with included equations of state (EOS) to take into account the behavior of water under standard conditions. Finally, an improvement of the LIFT technique which consists in using femtosecond lasers instead of nanosecond ones, is presented. It would allow to process smaller bioelements and to control the jet diameter, as it is directly related to the laser beam waist.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Self-consistent modeling of jet formation process in the nanosecond laser pulse regime

Laser induced forward transfer (LIFT) is a direct printing technique. Because of its high application potential, interest continues to increase. LIFT is routinely used in printing, spray generation and thermal-spike sputtering. Biological material such as cells and proteins have already been transferred successfully for the creation of biological microarrays. Recently, modeling has been used to explain parts of the ejection transfer process. No global modeling strategy is currently available. In this paper, a hydrodynamic code is utilized to model the jet formation process and estimate the constraints obeyed by the bioelements during the transfer. A self-consistent model that includes laser energy absorption, plasma formation via ablation, and hydrodynamic processes is proposed and confirmed with experimental results. Fundamental physical mechanisms via one-dimensional modeling are presented. Two-dimensional (2D) simplified solutions of the jet formation model equations are proposed. Predicted results of the model are jet existence and its velocity. The 2D simulation results are in good agreement with a simple model presented by a previous investigator.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Formation of nanocavities in dielectrics: A self-consistent modeling

Tight focusing of a subpicosecond laser pulse in transparent dielectrics is an efficient way to release laser energy and to produce plasma. A micro-explosion results in a submicrometer cavity formation if the deposited laser energy exceeds a threshold. A self-consistent model is developed that describes this process. The energy deposition is described by a full set of Maxwell's equations in the three-dimensional geometry and it accounts for nonlinear propagation phenomena in the femtosecond time scale. The calculated energy deposition is transferred to a hydrodynamic code that describes the cavity formation. Numerical simulations show that cavity size in silica depends strongly on the latent heat of sublimation. An equation of state is developed and introduced into the hydrodynamic model that takes into account the influence of such material parameters as the binding energy, the bulk modulus, and the Grueneisen coefficient. The cavity and shock-affected region sizes are compared to experimental data. This comparison suggests that laser micro-explosions might allow to tune the parameters of equations of state in the domain of phase transitions in a cold dense matter.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗