Search NASA⌕ Search

Engineering topics

Halpert, G.

Publications and source records attributed to Halpert, G..

At least 55 records · Page 3
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

(abstract) Effect of Electrolyte Composition on Carbon Electrode Performance

Rechargeable lithium cells containing lithium foil anodes are reported to have limited cycle life (at 100% DOD) performance and safety problems. These limitations are understood to be due to the high reactivity of elemental Li with the electrolyte and the formation of high surface area Li during cycling. To mitigate these problems, several lithium alloys and lithium intercalation compounds are being investigated as alternate lithium anode materials. Li(sub x)C has been identified as a promising lithium anode material due to its low equivalent weight, low voltage vs. Li, and improved stability towards various electrolytes. In this paper, we report the results of our studies on the electrolyte evaluation for the Li(sub x)C anode.

lithium carbon electrode electrolyte rechargeable ↗
NASA NTRS1993

Advanced Energy Storage for Space Applications

NASA is planning a number of space science and space exploration missions into the early 21st century. The JPL Advanced Battery Program, which has the goal of developing batteries for these missions, is described. Under program consideration are Li-SOCl(sub 2) cells, secondary lithium cells, advanced metal hydride cells, and high-temperature sodium-nickel chloride cells.

JPL Advanced Battery Program energy storage batter↗
NASA NTRS1993

Composite Solid Electrolyte for Li Battery Applications

The electrochemical, bulk and interfacial properties of the polyethylene oxide (PEO) based composite solid electrolyte (CSE) comprising LiI, PEO, and Al2O3 have been evaluated for Li battery applications. The bulk interfacial and transport properties of the CSEs seem to strongly depend on the alumina particle size. For the CSE films with 0.05 micron alumina while the bulk conductivity is around 10(exp -4) (mho/cm) at 103 C, the Li ion transport number seems to be close to unity at the same temperature. Compared to the PEO electrolyte this polymer composite electrolyte seems to exhibit robust mechanical and interfacial properties. We have studied three different films with three different alumina sizes in the range 0.01-0.3 micron. Effects of Al2O3 particle size on the electrochemical performance of polymer composite electrolyte is discussed. With TiS2 as cathode a 10 mAh small capacity cell was charged and discharged at C/40 and C/20 rates respectively.

Nagasubramanian, G.↗
NASA NTRS1993

Electrochemical impedance spectroscopy of lithium-titanium disulfide rechargeable cells

The two-terminal alternating current impedance of Li/TiS2 rechargeable cells was studied as a function of frequency, state-of-charge, and extended cycling. Analysis based on a plausible equivalent circuit model for the Li/TiS2 cell leads to evaluation of kinetic parameters for the various physicochemical processes occurring at the electrode/electrolyte interfaces. To investigate the causes of cell degradation during extended cycling, the parameters evaluated for cells cycled 5 times were compared with the parameters of cells cycled over 600 times. The findings are that the combined ohmic resistance of the electrolyte and electrodes suffers a tenfold increase after extended cycling, while the charge-transfer resistance and diffusional impedance at the TiS2/electrolyte interface are not significantIy affected. The results reflect the morphological change and increase in area of the anode due to cycling. The study also shows that overdischarge of a cathode-limited cell causes a decrease in the diffusion coefficient of the lithium ion in the cathode.

Narayanan, S. R.↗
NASA NTRS1993

Effect of cycling on the lithium/electrolyte interface in organic electrolytes

Nondestructive methods such as ac impedance spectroscopy and microcalorimetry are used to study the effect of cell cycling on the lithium/electrolyte interface. The reactivity of both uncycled and cycled lithium towards various electrolytes is examined by measuring the heat evolved from the cells under open-circuit conditions at 25 C by microcalorimetry. Cycled cells at the end of charge/discharge exhibited considerably higher heat output compared with the uncycled cells. After 30 d of storage, the heat output of the cycled cells is similar to that of the uncycled cells. The cell internal resistance increases with cycling, and this is attributed to the degradation of the electrolyte with cycling.

Surampudi, S.↗
NASA NTRS1993

Advances in Direct Methanol Fuel Cells at JPL

A new liquid feed direct methanol fuel cell has been developed based on a proton exchange membrane electrolyte and Pt/Ru and Pt catalyzed carbon fuel and air/O2 electrodes respectively.

Methanol Fuel↗
NASA NTRS1992

Effects of 12-crown-4 ether on the electrochemical performance of CoO2 and TiS2 cathodes in Li polymer electrolyte cells

The effect of adding 12-crown-4 ether (12Cr4) to the polyethylene oxide (PEO) electrolyte on the electrochemical properties of cells with Li(x)CoO2 or TiS2 as the cathode was investigated. The polymer electrolyte films were: (1) PEO, LiBF4; (2) PEO, LiBF4 with 12Cr4; (3) Li(x)CoO2, PEO, and LiBF4; and (4) Li(x)CoO2, PEO, LiBF4, and 12Cr4. It was found that, although 12Cr4 improved the cell performance over cells without 12Cr4 in the shallow c/d cycles (cyclic voltammetric behavior), it did not seem to prolong the active life of the cell. The cells with CoO2 as the cathode failed after a few c/d cycles, while similar cells with TiS2 did not fail even after 12 c/d cycles. The probable cause of failure in the case of CoO2 is ascribed to the instability of the CoO2 cathode.

Nagasubramanian, G.↗
NASA NTRS1992

Secondary lithium cells for space applications

It is concluded that secondary lithium batteries are suitable for planetary missions requiring high specific energy, long active shelf life, and limited cycle life. Titanium disulfide cathode material meet all the requirements for rechargeable lithium cell, including high intrinsic reversibility and realizable specific energy. Secondary lithium technology is still evolving, although low capacity cells have been demonstrated and greater than 700 cycle life was achieved. Work is in progress to improve the cycle life and safety of the electrolytes, alternate lithium anode, and the separators.

Surampudi, S.↗
NASA NTRS1992

Sodium-metal chloride batteries

It was concluded that rapid development in the technology of sodium metal chloride batteries has been achieved in the last decade mainly due to the: expertise available with sodium sulfur system; safety; and flexibility in design and fabrication. Long cycle lives of over 1000 and high energy densities of approx. 100 Wh/kg have been demonstrated in both Na/FeCl2 and Na/NiCl2 cells. Optimization of porous cathode and solid electrolyte geometries are essential for further enhancing the battery performance. Fundamental studies confirm the capabilities of these systems. Nickel dichloride emerges as the candidate cathode material for high power density applications such as electric vehicle and space.

Ratnakumar, B. V.↗
NASA NTRS1992

Design analysis of bipolar Li-TiS2 batteries

The present study uses an empirical model to assess the feasibility of using the Li-TiS2 bipolar battery for high power applications. Predicted performance outputs at a variety of conditions were calculated. The effects of the design parameters on the performance of bipolar Li-TiS2 batteries are presented. Specific energies greater than 150 Wh/kg can be achieved at low rates. Specific power levels in excess of 100 W/kg can be reached at high rates but with a reduction of the specific energy to less than 70 Wh/kg.

Shen, D. H.↗
NASA NTRS1991

Alternate cathodes for sodium-metal chloride batteries

Various metal chlorides were tested as possible cathode materials for sodium-metal batteries (in addition to Fe and Ni chlorides, which have been already developed to a stage of commercialization), using an electrochemical cell consisting of a pyrex tube, heated to 250 C, with the metal wire as working electrode, concentric Ni foil as counterelectrode, and high-purity Al as reference electrode. In particular, the aim of this study was to identify metal chlorides insoluble even in neutral melts, possible at the interface during overcharge, in order to eliminate the failure mode of the cell through a cationic exchange of the dissolved metal ions with sodium beta-double-prime alumina solid electrolyte. Results indicate that Mo and Co are likely alternatives to FeCl2 and NiCl2 cathodes in sodium batteries. The open circuit voltages of Na/CoCl(x) and Na/MoCl(x) cells at 250 C would be 2.55 V and 2.64 V, respectively.

Ratnakumar, B. V.↗
NASA NTRS1991

Evaluation of advanced NiCd cell designs for NASA applications

It is pointed out that an advanced NiCd cell based on a Hughes Aircraft Company design appears to show the most promise in the current generation of aerospace NiCd batteries. The cell was designed to ameliorate the major failure mechanisms of NiCd cells. This required cell design and process modifications and the use of alternate materials for some of the components (the most notable one being the substitution of zirconia cloth for nylon as the separator material). Recent reports in the literature indicate that the improvement in the performance of this technology appears to have been verified for GEO (geosynchronous)-type applications. The authors report on initial results of the evaluation of the advanced NiCd technology for applications of interest to NASA. They summarize the characteristics of cells based on the advanced technology from the time of manufacture to their current cell cycling status.

Di Stefano, S.↗