Search NASA⌕ Search

Engineering topics

Hamilton, H. H., II

Publications and source records attributed to Hamilton, H. H., II.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Hypersonic Aerodynamic Characteristics of a Proposed Single-Stage-To-Orbit Vehicle

The hypersonic aerodynamic characteristics of a winged body concept representing a candidate single- stage-to-orbit vehicle which features wing tip fin controllers and elevon/body flap control surfa'Fs are predicted at points along a nominal trajectory for Mach numbers from 5 to 27 and angles of attack from 19 to 32 degrees. Predictions are derived from surface properties based on flow solvers for inviscid and viscous, laminar flows acting as a perfect gas, as a gas in chemical equilibrium and as a gas in chemical non- equilibrium. At a Mach number of 22, the lateral aerodynamic characteristics of the vehicle are determined based on an inviscid analysis at side slip angles of 2 and 4 degrees and 32 degrees angle of attack; a viscous analysis was carried out to determine the effect of gas chemistry model on surface pressure and to determine the incremental aerodynamics for control surface deflections. The results show that the longitudinal pitch characteristics of the baseline configuration, i.e., zero control surface deflections, are significantly altered by real gas chemistry at angles of attack greater than 30 degrees and Mach numbers greater than 9; and, that aerodynamics derived from inviscid solutions are of sufficient accuracy for preliminary analysis. Also, it is shown that a Mach number of 22, the choice of gas chemistry model has a large impact on surface pressure levels at highly localized regions on the vehicle and that the vehicle can be trimmed at control surface deflections less than 11 degrees.

Weilmuenster, K. James↗
NASA NTRS1993

An approximate method for calculating heating rates on three-dimensional vehicles

An approximate method for calculating heating rates on three-dimensional vehicles at angle of attack is presented. The method is based on the axisymmetric analog for three-dimensional boundary layers and uses a generalized body fitted coordinate system. Edge conditions for the boundary layer solution are obtained from an inviscid flowfield solution, and because of the coordinate system used the method is applicable to any blunt body geometry for which a inviscid flowfield solution can be obtained. It is validated by comparing with experimental heating data and with Navier-Stokes calculations on the Shuttle orbiter at both wind tunnel and flight conditions and with Navier-Stokes calculations on the HL-20 at wind tunnel conditions.

Hamilton, H. H., II↗
NASA NTRS1991

Comparison of heating rate calculations with experimental data on a modified Shuttle orbiter at Mach 6

Heating-rate calculations from an 'engineering' code and a 'benchmark' Navier-Stokes code are compared with experimental wind tunnel data obtained on a 'modified' 0.0075-scale Shuttle orbiter at a Mach number of 6 and a freestream Reynolds number of 1.9 x 10 to the 6th/m. Comparisons are presented along the windward symmetry plane, in a circumferential direction around the body, and along the wing leading edge at angles of attack of 30 and 40 deg. Both codes provide accurate predictions of the heating rate over most of the body, but because the run time for the engineering code is relatively short, it is an ideal tool for both parametric and design studies.

Hamilton, H. H., II↗
NASA NTRS1991

Flight stagnation-point heating calculations on Aeroassist Flight Experiment vehicle

NASA's Aeroassist Flight Experiment (AFE) vehicle will be deployed from the Space Shuttle Orbiter in 1994 to make a data-gethering aeropass through the upper atmosphere before returning to orbit for Shuttle pickup. An axisymmetric, chemically-reacting viscous shock-layer code is presently used to calculate AFE heating rates which automatically accounts for the viscous-inviscid interaction and entropy layer-swallowing effects which are ignored by the conventional boundary-layer methods. Results are presented for the stagnation-point heating of the current AFE baseline trajectory.

Hamilton, H. H., II↗
NASA NTRS1986

Geometerial description for a proposed aeroassist flight experiment vehicle

One geometry currently under consideration for the Aeroassist Flight Experiment (AFE) vehicle is composed of several segments of simple general conics: an ellipsoidal nose tangent to an elliptical cone and a base skirt with the base plane raked relative to the body axis. An analytic representation for the body coordinates and first and second partial derivatives of this configuration has been developed. Equations are given which define the body radius and partial derivatives for a prescribed axial and circumferential position on the vehicle. The results for a sample case are tabulated and presented graphically.

Cheatwood, F. M.↗
NASA NTRS1986

Time-dependent solution for axisymmetric flow over a blunt body with ideal gas, CF4, or equilibrium air chemistry

A time-asymptotic method has been used to obtain steady-flow solutions for axisymmetric inviscid flow over several blunt bodies including spheres, paraboloids, ellipsoids, and spherically blunted cones. Comparisons with experimental data and results of other computational methods have demonstrated that accurate solutions can be obtained using this approach. The method should prove useful as an analysis tool for comparing with experimental data and for making engineering calculations for blunt reentry vehicles.

Hamilton, H. H., II↗
NASA NTRS1986

Calculation of convective heating on proposed aeroassist flight experiment vehicle

Convective heating calculations of a NASA aeroassist flight experiment (AFE) configuration consisting of a blunted, elliptic cone raked off at the base, and fitted with a skirt-type afterbody with a generous corner radius, are presented. The HALIS inviscid flowfield code is used to supply edge properties to an approximate three-dimensional boundary-layer method to calculate the surface heating. Calculations at Mach number 9.86 and approximate Reynolds number of 500,000, for angles of attack from -10 to 10 degrees, are in general good agreement with Langley 31-inch Mach 10 Tunnel experimental data. The results validate the application of the present overall AFE configuration heating pattern heating contours to aeroassist orbital transfer vehicle heating distribution determinations.

Hamilton, H. H., II↗
NASA NTRS1986

A comparison of computed and measured aerodynamic characteristics of a proposed aeroassist flight experiment configuration

The use of experimental or computed data to evaluate the performance of aeroassist orbital transfer vehicles (AOTVs) is discussed. Aerodynamic and surface pressure data are derived from computed flowfield solutions (the HALIS inviscid flowfield code), the Newtonian theory, and ground-based, wind tunnel studies (hypersonic He tunnel, 31-inch Mach 10 tunnel, and a hypersonic CF4 tunnel). The wind tunnel and HALIS models were tested at angles-of-attack that ranged from -10 to 10 deg. The effects of the ellipticity of the nose, the radius of the circular arc, and the angle through which the arc passes on the aerodynamic characteristics of the vehicles are examined. It is observed that the HALIS and CF4 tunnel generated surface pressure on the AOTVs produced the most useful aerodynamic data. Good correlation is obtained for the experimental and computational data; however, the Newtonian results do not correspond to the tunnel/HALIS data.

Weilmuenster, K. J.↗
NASA NTRS1986

A comparison of computed and experimental surface pressure and heating on 70 deg sphere cones at angles of attack to 20 deg

A method for handling the flow fields around 70 deg spherical cones at angles of attack up to 20 deg is described. Surface pressure and heating results are compared with existing wind tunnel data. Computed surface pressures are found to be in excellent agreement with experimental data, while the surface heating from approximate and finite difference forms of the boundary layer equations are in good agreement with the data. The effect of bluntness ratio on surface pressures and heating is very small. Body corner radius, while not having a significant impact on body aerodynamics, produced large changes in surface pressure and heating distribution.

Weilmuenster, K. J.↗
NASA NTRS1983

A review of preflight estimates of real-gas effects on space shuttle aerodynamic characteristics

Preflight estimates of the hypersonic aerodynamic characteristics of the Shuttle orbiter were based on a diverse series of research studies using state of the art techniques developed by basic research in the 60's and 70's. Real-gas viscous calculations on simple shapes that were used to evaluate correlation parameters indicated that real-gas effects reduce aerodynamic forces and moments. Inviscid calculations on winged lifting shapes indicated reduced forces and a slight nose-up pitch resulted because of real-gas effects. Analysis of the extensive wind tunnel data base indicated viscous correlation parameters provided the most appropriate extrapolation technique for estimating flight aerodynamics. Variations because of changes in the ratio of specific heats, which was the only available experimental tool for evaluating real-gas effects, indicated that reduced loads and nose-up pitching moments would occur at high altitudes and Mach numbers but that the values would not exceed the tolerances and variations established about the aerodynamic design data book values derived from viscous correlations. During STS-1, nose-up pitching moments exceeded the established variations.

Woods, W. C.↗
NASA NTRS1983

Orbiter catalytic/noncatalytic heat transfer as evidenced by heating to contaminated surfaces on STS-2 and STS-3

During that portion of Space Shuttle orbiter entry when significant aerodynamic heat transfer occurs, the flow over the vehicle is in chemical nonequilibrium. The parameter which most significantly influences the level of surface heat transfer in such a flow field is the catalytic efficiency of the surface with respect to the recombination of dissociated oxygen atoms. Significant, and instantaneous, changes were observed in the level of heat transfer at several lower surface centerline locations on STS-2 and STS-3. This phenomenon apparently resulted from a sudden change in the surface catalytic efficiency at these locations due to contamination of the surface by metallic oxides. As a result, data obtained from affected measurements cannot be considered as benchmark data with which to attempt to characterize nonequilibrium heat transfer to the orbiter's lower surface centerline.

Throckmorton, D. A.↗
NASA NTRS1983

Filler bar heating due to stepped tiles in the shuttle orbiter thermal protection system

An analytical study was performed to investigate the excessive heating in the tile to tile gaps of the Shuttle Orbiter Thermal Protection System due to stepped tiles. The excessive heating was evidence by visible discoloration and charring of the filler bar and strain isolation pad that is used in the attachment of tiles to the aluminum substrate. Two tile locations on the Shuttle orbiter were considered, one on the lower surface of the fuselage and one on the lower surface of the wing. The gap heating analysis involved the calculation of external and internal gas pressures and temperatures, internal mass flow rates, and the transient thermal response of the thermal protection system. The results of the analysis are presented for the fuselage and wing location for several step heights. The results of a study to determine the effectiveness of a half height ceramic fiber gap filler in preventing hot gas flow in the tile gaps are also presented.

Petley, D. H.↗
NASA NTRS1983

Calculation of inviscid flow over shuttle-like vehicles at high angles of attack and comparisons with experimental data

A computer code HALIS, designed to compute the three dimensional flow about shuttle like configurations at angles of attack greater than 25 deg, is described. Results from HALIS are compared where possible with an existing flow field code; such comparisons show excellent agreement. Also, HALIS results are compared with experimental pressure distributions on shuttle models over a wide range of angle of attack. These comparisons are excellent. It is demonstrated that the HALIS code can incorporate equilibrium air chemistry in flow field computations.

Weilmuenster, K. J.↗
NASA NTRS1982

Approximate Method of Calculating Heating Rates at General Three-Dimensional Stagnation Points During Atmospheric Entry

An approximate method for calculating heating rates at general three dimensional stagnation points is presented. The application of the method for making stagnation point heating calculations during atmospheric entry is described. Comparisons with results from boundary layer calculations indicate that the method should provide an accurate method for engineering type design and analysis applications.

Hamilton, H. H., II↗
NASA NTRS1982

Preliminary Analysis of STS-3 Entry Heat-Transfer Data for the Orbiter Windward Centerline

A preliminary analysis of heat transfer data on the space shuttle orbiter windward centerline for the STS-3 mission entry is presented. Temperature-time history plots for each measurement location and tabulated wall temperature and convective heating rate data at 21 selected trajectory points are included. The STS-3 flight data are also compared with predictions by two approximation methods for computing convective heat transfer rates in equilibrium air.

Throckmorton, D. A.↗
NASA NTRS1982

Approximate method of predicting heating on the windward side of Space Shuttle Orbiter and comparisons with flight data

An approximate method is developed for predicting laminar and turbulent heating rates on the windward side of the Space Shuttle Orbiter for both the wind-tunnel and flight environments. The method is based on a 'local infinite swept cylinder' analysis and includes both equilibrium-air chemistry and variable boundary-layer-edge entropy. The method is validated by comparing with data from wind-tunnel experiments and from the first and second Space Shuttle flights both along the windward-symmetry plane and in a lateral direction off the symmetry plane. Agreement with the flight data is good from approximately 67 km (peak heating) downward.

Hamilton, H. H., II↗