Search NASA⌕ Search

Engineering topics

Hamilton, H. Harris

Publications and source records attributed to Hamilton, H. Harris.

9 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Development of a Boundary Layer Property Interpolation Tool in Support of Orbiter Return To Flight

A new tool was developed to predict the boundary layer quantities required by several physics-based predictive/analytic methods that assess damaged Orbiter tile. This new tool, the Boundary Layer Property Prediction (BLPROP) tool, supplies boundary layer values used in correlations that determine boundary layer transition onset and surface heating-rate augmentation/attenuation factors inside tile gouges (i.e. cavities). BLPROP interpolates through a database of computed solutions and provides boundary layer and wall data (delta, theta, Re(sub theta)/M(sub e), Re(sub theta)/M(sub e), Re(sub theta), P(sub w), and q(sub w)) based on user input surface location and free stream conditions. Surface locations are limited to the Orbiter s windward surface. Constructed using predictions from an inviscid w/boundary-layer method and benchmark viscous CFD, the computed database covers the hypersonic continuum flight regime based on two reference flight trajectories. First-order one-dimensional Lagrange interpolation accounts for Mach number and angle-of-attack variations, whereas non-dimensional normalization accounts for differences between the reference and input Reynolds number. Employing the same computational methods used to construct the database, solutions at other trajectory points taken from previous STS flights were computed: these results validate the BLPROP algorithm. Percentage differences between interpolated and computed values are presented and are used to establish the level of uncertainty of the new tool.

Greene, Francis A.↗
NASA NTRS2001

Research on Streamlines and Aerodynamic Heating for Unstructured Grids on High-Speed Vehicles

Engineering codes are needed which can calculate convective heating rates accurately and expeditiously on the surfaces of high-speed vehicles. One code which has proven to meet these needs is the Langley Approximate Three-Dimensional Convective Heating (LATCH) code. It uses the axisymmetric analogue in an integral boundary-layer method to calculate laminar and turbulent heating rates along inviscid surface streamlines. It requires the solution of the inviscid flow field to provide the surface properties needed to calculate the streamlines and streamline metrics. The LATCH code has been used with inviscid codes which calculated the flow field on structured grids, Several more recent inviscid codes calculate flow field properties on unstructured grids. The present research develops a method to calculate inviscid surface streamlines, the streamline metrics, and heating rates using the properties calculated from inviscid flow fields on unstructured grids. Mr. Chris Riley, prior to his departure from NASA LaRC, developed a preliminary code in the C language, called "UNLATCH", to accomplish these goals. No publication was made on his research. The present research extends and improves on the code developed by Riley. Particular attention is devoted to the stagnation region, and the method is intended for programming in the FORTRAN 90 language.

DeJarnette, Fred R.↗
NASA NTRS2001

N-Factor Computations for the X-33 Vehicle

N-Factor computations for the X-33 vehicle on the lower side of the body were per-formed. The transition prediction code e-Malik was used to compute the N-Factors and the meanflow field was computed using the CFD code LAURA. The computations are done at two angles of attack 30 and 40 degrees and the freestream Mach number and Reynolds number are M= 6 and Re = 7.7* 10(exp 6). The N-Factors obtained are very low in the range of 2-3 near the experimentally observed transition onset regions. The stability computations show that at 30 degrees angle of attack, the transition occurs due to crossflow instability and at higher angles of attack the transition occurs due to first mode inviscid instability.

Balakumar, P.↗
NASA NTRS2001

Qualitative Assessment of the Acoustic Disturbance Environment in the NASA LaRC 20-Inch MACH 6 Wind Tunnel

An experimental investigation was conducted on a 5-degree-half-angle cone with a flare in a conventional Mach 6 wind tunnel to examine the effect of facility noise on boundary layer transition. The effect of tunnel noise was inferred by comparing transition onset locations determined from the present test to that previously obtained in a Mach 6 quiet tunnel. Together, the two sets of experiments are believed to represent the first direct comparison of transition onset between a conventional and a quiet hypersonic wind tunnel using a common test model. In the present conventional hypersonic tunnel experiment, adiabatic wall temperatures were measured and heat transfer distributions were inferred on the cone flare model at zero degree angle of attack over a range of length Reynolds numbers (2 x 10(exp 6) to 10 x 10(exp 6)) which resulted in laminar and turbulent flow. Wall-to-total temperature ratio for the transient heating measurements and the adiabatic wall temperature measurements were 0.69 and 0.86, respectively. The cone flare nosetip radius was varied from 0.0001 to 0.125-inch to examine the effects of bluntness on transition onset. At comparable freestream conditions the transition onset Reynolds number obtained on the cone flare model in the conventional "noisy" tunnel was approximately 25% lower than that measured in the low disturbance tunnel.

Horvath, Thomas J.↗
NASA NTRS1994

Approximate method for calculating heating rates on three-dimensional vehicles

An approximate method for calculating heating rates on three-dimensional vehicles at angle of attack is presented. The method is based on the axisymmetric analog for three-dimensional boundary layers and uses a generalized body-fitted coordinate system. Edge conditions for the boundary-layer solution are obtained from an inviscid flowfield solution, and because of the coordinate system used, the method is applicable to any blunt body geometry for which an inviscid flowfield solution can be obtained. The method is validated by comparing with experimental heating data and with thin-layer Navier-Stokes calculations on the shuttle orbiter at both wind-tunnel and flight conditions and with thin-layer Navier-Stokes calculations on the HL-20 at wind-tunnel conditions.

Hamilton, H. Harris↗
NASA NTRS1988

Overview of CFD methods and comparison with flight aerothermal data

An overview of previously published aerothermal investigations which demonstrate the capabilities of detailed computational fluid dynamics and engineering codes to predict the aerothermal environment about an entry vehicle is presented. The overview consists of a brief discussion of the computational methods and experimental data and includes comparisons between the computed results and data. The overview focuses primarily on analyses of flight data since these data provide the unique capability to assess the real-gas chemistry options in the codes. The computed results are based on a series of codes which are employed by the Aerothermodynamics Branch of the Space System Division at the Langley Research Center. The flight data, which were measured on the Reentry F, the Space Shuttle, and the Fire II vehicles, represent a wide range of vehicle configurations and freestream conditions. Also, results of one recent set of ground tests are included since the tests provide data on a model of a pending flight project. The comparisons of the predicted results and data demonstrate the adequacy of the present computational fluid dynamics capabilities and indicate the potential to predict the aerothermal environment about future flight vehicles.

Sutton, Kenneth↗
NASA NTRS1972

Inviscid surface streamline program for use in predicting shuttle heating rates

A number of methods are currently under development for computing the exact three-dimensional flow field about real configurations. However, even when these methods are available, they will require large computational times on present generation computers. Thus, there is still a need to develop approximate methods to solve three-dimensional flow problems. An inviscid-surface-streamline program (for predicting shuttle heating rates) which uses approximate methods to obtain a solution is described.

Hamilton, H. Harris↗