Search NASA⌕ Search

Engineering topics

Han, Ming

Publications and source records attributed to Han, Ming.

Simultaneous measurement of temperature and strain by cascaded fiber Bragg grating-silicon Fabry-Perot interferometer sensor

We report a fiber-optic sensor configuration with a cascaded fiber Bragg grating (FBG) and a silicon Fabry-Perot interferometer (FPI) for simultaneous measurement of temperature and strain. The sensor is composed of a 5 mm FBG on a single mode fiber and a 100μm thick silicon FPI attached to the tip of the optical fiber. The FBG is surface mounted on the host structure, and the FPI tip is suspended. Due to the stress-free, cantilever configuration, the silicon FPI is insensitive to strain, but sensitive to temperature with a sensitivity much higher than the FBG due to the large thermo-optic coefficient of silicon. The sensor is tested from room temperature to 100°C with varying strain up to ∼150με. The silicon FPI provides high temperature sensitivity of 89 pm/°C unaffected by strain. Since the FBG is attached to the host structure, it is affected by both thermal and mechanical strain; the sensitivity of these was experimentally obtained 32 pm/°C and 1.09 pm / με, respectively. Interrogated with a broadband light source and a high-speed spectrometer, the sensor shows temperature and strain resolutions of 1.9 × 10 −3 °C and 0.042 με, respectively. Here, due to the small size, enhanced sensitivity, and high resolution, this cascaded FBG-FPI sensor can be used in applications where accurate measurement of temperature and strain is required.

42 ENGINEERING↗

Fiber Optic Temperature Sensor Using Dual Air- Filled Fabry-Pérot Cavities With Variable Pressure

We present an approach for high temperature measurement using a pair of fiber-optic Fabry–Pérot (FP) cavities filled with gas of identical but variable pressure. One of the FPs (reference FP) is placed in the cold zone with a known temperature. The temperature of the measuring FP can be deduced by the spectral fringe shift vs. pressure of the two FPs. This method does not require measurement of the pressure or the knowledge of the optical properties of the gas. The use of gas as the sensing material and the measurement mechanism also implies long-term stability and eliminates the cross-sensitivity to strain. We fabricated the sensors and tested them for measuring temperature up to 800 °C. Here, the sensor shows good linearity in the range. Long-term test conducted at 800 °C exhibited the stability of the sensor with fluctuations of ≤0.3% over a duration exceeding 100 hours.

42 ENGINEERING↗

SSR COST – COmposite Structural Technologies for advanced reactor deployment (Final Scientific/Technical Report)

Moltex is designing a Generation 4 or Advanced nuclear reactor, the molten salt fast spectrum SSR-W. The design intent is to reduce the cost and complexity of the nuclear systems by relying on inherent safety characteristics, instead of engineered systems. One such characteristic as a natural tendency for power to decrease as temperature increases. Another characteristic that improves natural safety is the fact that the working fluids (molten salts) are at atmospheric pressure at operating temperatures. This significantly reduces the need for pressure boundary components and systems. Moltex is highly motivated to develop simple and economic reactors to reduce the carbon intensity and improve energy security of global electricity production. The COST project investigated the opportunities for reducing construction cost of advanced reactors with the adoption of Rigid Elastic Composite Civil works (RECC). The construction design and methods used in currently operational light water power plants would generally be suboptimal for the SSR-W since there is no requirement for civil structures to withstand high pressure accidents such as hydrogen combustion or steam explosion. In parallel to downselecting the most promising RECC-type technology, accident scenarios representing the largest credible challenge to the SSR-W civil and construction design were modelled. The capability of an SSR-W reactor constructed with and without the selected construction technology was evaluated and the consequential licensing challenges identified. A construction schedule and cost estimate of the SSR-W with and without the selected RECC construction technology was developed. Once the above data was collected, then Moltex was able to review the safety performance, license-ability and cost/schedule benefit of applying the preferred construction technology. The CAPEX/NPV benefit was quantified, and the licensing risks and opportunities were documented. Finally, the CAPEX/NPV benefit of the advanced construction technology was modest due to the suitability of traditional stick-built construction for the SSR-W design. However, previously unidentified benefits of the advanced construction technology were revealed during the studies that could credibly de-risk certain aspects of the design to be licensed. Since licensing (duration and delays) are very significant in new build project costs, the cost benefits may be significant. Further studies on the risk reduction of the construction technology are foreseen.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Fiber-Optic Bolometer and Calorimeter Arrays for Magnetically Confined Plasmas

Bolometers measure the plasma radiation and provide essential diagnostic information both for safe, sustainable operation of magnetic-confinement fusion (MCF) devices and for study of the relevant physics. The fusion community has been replying on resistive bolometers for plasma radiation measurement. However, their performance is greatly compromised by the strong electromagnetic interference present in MCF devices. Previously, we have demonstrated a fiber-optic bolometer that has the promise to overcome the challenges related to the strong EMI in the MCF environment. In this project, we study the performance of the fiber-optic bolometer in a simulated MCF environment and improved the sensitivity through a novel sensor design. Part of the work reported here was performed between 09/01-12/31/2017 when the PI was with University of Nebraska-Lincoln under the same project but with a different award number (DE-SC0018273).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Fluctuating hydrodynamics of chiral active fluids

Active materials are characterized by continuous injection of energy at the microscopic level and typically cannot be adequately described by equilibrium thermodynamics. Here we study a class of active fluids in which equilibrium-like properties emerge when fluctuating and activated degrees of freedom are statistically decoupled, such that their mutual information is negligible. We analyse three paradigmatic systems: chiral active fluids composed of spinning frictional particles that are free to translate, oscillating granular gases and active Brownian rollers. In all of these systems, a single effective temperature generated by activity parameterizes both the equation of state and the emergent Boltzmann statistics. The same effective temperature, renormalized by velocity correlations, relates viscosities to steady-state stress fluctuations via a Green–Kubo relation. To rationalize these observations, we develop a theory for the fluctuating hydrodynamics of these non-equilibrium fluids and validate it through large-scale molecular dynamics simulations. Our work sheds light on the microscopic origin of odd viscosities and stress fluctuations characteristic of parity-violating fluids, in which mirror symmetry and detailed balance are broken.

74 ATOMIC AND MOLECULAR PHYSICS↗

Fiber-Optic Silicon Fabry-Perot Interferometric Bolometer: The Influence of Mechanical Vibration and Magnetic Field

Plasma radiation plays an important role in the operation and control of magnetic confinement fusion and is typically measured by bolometers. Here, we study the influence of mechanical vibration and magnetic field, which are typically present in magnetic confinement fusion devices, on the performance of a fiber-optic bolometer (FOB) based on silicon Fabry-Perot interferometer (FPI) demodulated by a scanning diode laser. It is found that both the vibration and magnetic field could cause large noise due to the birefringence of the silicon FPI. To mitigate the birefringence effects, we demonstrated two effective methods: polarization maintaining FOB and polarization scrambling. We show that two methods can be effective in mitigating the effect caused by the sensor birefringence: (1) replacing the regular single-mode fiber in the FOB system with polarization-maintaining fiber and (2) using a polarization scrambler after the laser source. For both methods, no significant increase in the noise was observed in the vibration and magnetic field tests. Finally, our research highlights the importance of the polarization management for the FOB systems toward their practical applications in magnetic-confinement fusion systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Fiber optic bolometer

The present disclosure is directed to a fiber optic bolometer device. In an implementation, a fiber optic bolometer device includes an optical fiber and a silicon layer that comprises a Fabry-Pérot interferometer. The silicon layer includes a first surface and a second surface. The fiber optic bolometer device includes a reflective dielectric film disposed over the first surface of the silicon layer where the reflective dielectric film is adjacent to an end face of the optical fiber. The fiber optic bolometer device also includes an absorptive coating disposed over the second surface of the silicon layer (e.g., the surface distal to the end face of the optical fiber).

36 MATERIALS SCIENCE↗

Fiber-Optic Bolometer and Calorimeter Arrays for Magnetically Confined Plasmas Final Technical Report

Exhaust control is critical for sustained and safe operation of magnetic confinement fusion (MCF), which requires bolometers to measure the radiations converted from the exhaust power. Traditional bolometers are based on a radiation absorber and a resistive temperature sensor and their performance is greatly compromised by the strong electromagnetic interference (EMI). Previously, we have demonstrated a fiber-optic bolometer that has the promise to overcome the challenges related to the strong EMI in the MCF environment. However, it shows relatively large noise that limits its usefulness in MCF applications. In this project, we reduced the noise by more than 20 times through novel sensor design and signal demodulation. The availability of such bolometers will help to better understand and control the exhaust control strategies in MCF. The original project duration was three years. Because the PI moved to another institution on 1/1/2018, the project was closed after four months and a new grant was awarded to the PI in his new institution to continue the work.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reversible self-assembly of superstructured networks

Soft structures in nature, such as protein assemblies, can organize reversibly into functional and often hierarchical architectures through noncovalent interactions. Molecularly encoding this dynamic capability in synthetic materials has remained an elusive goal. We report on hydrogels of peptide-DNA conjugates and peptides that organize into superstructures of intertwined filaments that disassemble upon the addition of molecules or changes in charge density. Experiments and simulations demonstrate that this response requires large-scale spatial redistribution of molecules directed by strong noncovalent interactions among them. Simulations also suggest that the chemically reversible structures can only occur within a limited range of supramolecular cohesive energies. Storage moduli of the hydrogels change reversibly as superstructures form and disappear, as does the phenotype of neural cells in contact with these materials.

36 MATERIALS SCIENCE↗

Effective temperature concept evaluated in an active colloid mixture

Significance In the long-standing debate on whether the insights of statistical thermodynamics could apply to nonequilibrium systems, a key unsolved problem is whether it is useful to postulate an emergent effective temperature, different from the thermal temperature. Here, we introduce a two-component system of driven Janus colloids such that collisions induced by external energy sources play the role of temperature. We find that this nonequilibrium system quantitatively behaves as if at equilibrium, with collisions caused by differential rhythmic motion between the two components acting as a strict analog to thermal motion. We demonstrate that the effective temperature can serve as a common control parameter for both kinetics and phase behavior.

36 MATERIALS SCIENCE↗

Pt nanoparticles modified by rare earth oxides: Electronic effect and influence to catalytic hydrogenation of 3-phenoxybenzaldehyde

Graphical abstract: - Highlights: • The rare earths modified Pt/Al{sub 2}O{sub 3} were prepared by colloidal deposition method. • Modification of Pt by the rare earth enhanced catalytic hydrogenation activity. • The activity improvement is due to electron interaction between Pt and rare earth. • The hydrogenation mechanism of rare earth modified Pt catalyst was proposed. - Abstract: The rare earth elements (La, Ce, Nd, Sm, Pr, and Gd) modified Pt/Al{sub 2}O{sub 3} catalysts were prepared by the colloidal deposition and chemical reduction methods, respectively. Pt nanoparticles with average size 3 ± 0.5 nm were uniformly dispersed on the surface of Al{sub 2}O{sub 3} for the samples prepared by the colloidal deposition method, which exhibited higher activities in the hydrogenation of 3-phenoxybenzadehyde than the corresponding samples prepared by chemical reduction method. Moreover, except Gd, the catalysts modified by rare earth elements showed better catalytic performance than unmodified Pt/Al{sub 2}O{sub 3}. For Pt–Ce/Al{sub 2}O{sub 3} catalyst, when the weight percent of Pt and Ce was 0.5 and 0.25, respectively, the hydrogenation conversion of 3-phenoxybenzaldehyde was 97.3% after 6 h reaction. This activity improvement is due to the electronic interaction between Pt and rare earth elements, which was investigated by X-ray photoelectron spectroscopy.

36 MATERIALS SCIENCE↗