Search NASA⌕ Search

Engineering topics

Han, Yinglei

Publications and source records attributed to Han, Yinglei.

Comparison of the Chemical Composition of Liquids from the Pyrolysis and Hydrothermal Liquefaction of Lignocellulosic Materials

Major differences in thermal stability and hydrotreatment behavior of HTL and pyrolysis oils have been reported in the literature. However, little is known about the variations in the chemical composition of these oils that could explain such differences. Two commercial wood pyrolysis oils (Pyrovac and BTG), and their water-soluble (WS) and water-insoluble fractions (WIS) were analyzed and compared with the aqueous (WS WD-57 ) and oily (WIS WS-57 ) fractions obtained from hydrothermal liquefaction (HTL) of Douglas-fir. The samples were characterized by GC/MS, Karl Fischer titration, carbonyl content, total acid number, elemental composition, calorific value, proximate analysis, Fourier Transform Infrared Spectroscopy (FTIR), Folin-Ciocalteu (FC), and UV fluorescence. All the fractions were also analyzed by Fourier Transform Ion Cyclotron Resonance Mass Spectroscopy (FT-ICR-MS) and by Electrospray Ionization (EI). The most prevalent class of compounds in the water insoluble phases were phenols derived from lignin. Water-soluble phases contain mostly the oxygenated compounds derived from cellulose and hemicellulose and were richer in carbonyl functional groups. The water content of the resulting aqueous phases were between: 65 (WS BTG ) and 96 (WS Pyrovac ) wt. %. The bio-oil from BTG has higher water content and lower HHV, compared to Pyrovac oil. The GC/MS results of BTG oil show the presence of a more prominent acetic acid peak and higher TAN number than the Pyrovac oil. The GC/MS of Pyrovac oil showed more obvious mono-phenol peaks. The quantification of this family by Folin-Ciocalteu method confirmed higher content of monophenolic compounds compared with the BTG oil. The lower thermal stability of pyrolysis oils compared with HTL biocrudes can be partially explained by the fact that pyrolysis oils (BTG and Pyrovac) contain carbohydrates while HTL biocrude (WIS WD-57 ) doesn’t. Thus, we decided to further investigate the chemical differences between the phenolic rich fractions insoluble in water and the holocellulose derived compounds soluble in water. Even after water extraction, the acid content of the water insoluble fraction from BTG (WISBTG) was higher than the acid content of the water insoluble fraction obtained by HTL (WISWSD-57). Likewise, the acid content of the aqueous phases derived from pyrolysis oils (WS Pyrovac , WS BTG ) was also higher than for the aqueous phase obtained by HTL (WSWSD-57). This result is in part due to the use of bases in the HTL process that neutralizes the acid formed in that process. Moreover, the starting feedstock may also influence the differences between the oils. Although, the UV-Fluorescence spectra, ICR-MS and the EI analyses showed some minor differences in the molecular weight and chemical make-up of the oligomers soluble and insoluble in water from pyrolysis and HTL; the differences observed were not large enough to justify the differences in behavior between these oils reported in the literature. Our results suggest that the differences observed between HTL biocrudes and pyrolysis oils are likely partially due to the presence of holocellulose derived products in the pyrolysis oils and higher acid contents.

09 BIOMASS FUELS↗

Co-Hydrotreatment of Yellow Greases and the Water-Insoluble Fraction of Pyrolysis Oil. Part I: Experimental Design to Increase Kerosene Yield and Reduce Coke Formation

Here, this paper reports the co-hydrotreatment of Biomass Technology Group commercial pyrolysis oil water-insoluble (WIS) phase (also known as pyrolytic lignin) and yellow greases (waste cooking oil), aiming to produce sustainable aviation fuels (SAFs). We use a sulfided NiMo/Al 2 O 3 blend with 16 wt % WIS and a central composite experimental design to identify processing conditions increasing kerosene yield and reducing coke formation. The input variables were: (1) reaction temperature (320, 350, and 380 °C), (2) initial hydrogen pressure (5, 6, and 7 MPa), and (3) amount of catalyst (0.7, 1.0, and 1.3 g). The hydrotreated oily phases were distilled to obtain gasoline (<150 °C), kerosene (150–250 °C), diesel (250–350 °C), and residual oil (>350 °C). The reaction temperature is the main factor affecting the yield of gaseous, solid, and liquid products. Meanwhile, a higher initial hydrogen pressure and catalyst loading increased the yield of kerosene and other distillates and decreased the coke formation. A high temperature correlated with a lower content of oxygenates in kerosene cuts. Based on our experimental results, we propose to conduct hydrotreatment studies at 380 °C, initial H 2 pressure of 7 MPa, and 1.3 g of catalyst. Under the identified conditions, it was possible to improve the kerosene yield to more than 20 wt % and reduce the yield of coke to close to 2.0 wt %. The chemical composition and fuel properties of the gasoline, kerosene, and diesel cuts were thoroughly analyzed. The content of aromatics and phenols in the kerosene fraction produced at the conditions identified in this project exceeded the recommended values for SAFs. New strategies (such as blending and more intense hydrotreatment to remove oxygenated compounds) need to be implemented to reduce the content of these molecules in our final product.

09 BIOMASS FUELS↗

Ternary Phase Diagram of Water/Bio-Oil/Organic Solvent for Bio-Oil Fractionation

Separating bio-oil by fractionation with different chemical composition is a critical step to refine these oils and obtain high value products. Cold-water precipitation of pyrolytic lignin from bio-oil is the most common approach used. However, the obtained aqueous phase from this method still contain phenols, is diluted and difficult to use. In this study, the use of liquid-liquid extraction with different solvents (1-butanol, ethyl acetate, 1-octanol, dichloromethane, toluene, and hexane) for the separation of targeted molecules (lignin oligomers, sugars, acetic acid) is explored. Ternary phase diagrams for the organic solvent/water/bio-oil are reported. The partition coefficient of compounds of interest (both light and heavy fraction) is reported for the liquid-liquid equilibrium zone. When using butanol as solvent, the highest separation factor of total phenols over total sugars was observed. Furthermore, our results provide information to design L-L separation units with the capacity to selectively recover targeted molecules from pyrolysis oils.

09 BIOMASS FUELS↗

Hydrotreatment of pyrolysis bio-oil: A review

Fast pyrolysis is an effective process to convert more than 60 wt. % of lignocellulosic materials into a bio-oil that can be further hydrotreated for transportation fuel production. However, bio-oil is acidic, viscous, and chemically unstable due to its high oxygen content. Therefore, increasing attention has being paid to deoxygenation of bio-oil through catalytic hydrotreatment into a “drop-in” fuel has been gaining attention from researchers. The first section of this review is devoted to summarize our current understanding of bio-oil composition. Bio-oil hydrotreatment is typically conducted in two-steps. In the first step, known as stabilization, the reactive carbonyl and carboxyl functional groups are transformed into alcohols at a temperature between 373 and 573 K. In the second step, between 623 and 673 K, cracking and hydro-deoxygenation (HDO) occurs. The most common catalysts used in the stabilization step are noble metals (Pt, Ru, Pd) supported on carbon and metal oxides (TiO2, Al2O3, SiO2, Fe2O3, ZrO2). The most common catalysts for deoxygenation and hydrocracking are sulfided CoMo or NiMo. More recently transition metal phosphides and carbides have been shown to be active. The effect of hydrotreatment parameters and the main global reaction mechanisms are discussed. In the first section, we update the progresses made on bio-oil composition, followed by a detailed discussion on the role of heterogeneous catalysts. Many of the bio-oil hydrotreament studies in the literature are based on model compound results. The reactions revealed by such approach are summarized and discussed. Although these studies provide valuable information for developing upgrading strategies, bio-oil chemistry is difficult to describe by model compounds. Thus, we also reviewed a smaller number of hydrotreatment studies of pyrolysis oil fractions. The presence of several oxygenated functional groups (phenols, carboxylic acids, carbonyls, alcohols) in monomeric and oligomeric molecules is a major challenge to study hydrotreatment reactions. Under realistic industrial operational conditions undesirable polymerization and crosslinking reactions leading to catalyst deactivation are very important. In spite of the extensive work on bio-oil hydrotreatment, the nature of the reactions happening in these complex oils is still poorly known. Pyrolytic lignin and sugars have been identified as important contributors to coke formation. Both fractions can then undergo successful hydrogenation or hydrogenolysis over the catalysts. The review ends with a discussion on future prospects and challenges to hydrotreat pyrolysis oils. Because bio-oil is a liquid formed by hundreds of molecules covering a wide range of molecular weights and functionalities, it is very unlikely that a single hydrotreatment technology that makes a good use of each of its molecules could be found. In fact, current hydrotreatment schemes sacrifice some fractions (convert them into low value products) to maximize the conversion of others into fuel. Separation of bio-oil in fractions and processing of each of them via hydrotreatment or by other suitable technology at optimized conditions with well suited catalysts to obtain high value products seems to be the most promising path to reduce hydrogen consumption, coke formation and enhance the economic viability of bio-oil refineries.

Han, Yinglei↗