Search NASA⌕ Search

Engineering topics

Haner, David A.

Publications and source records attributed to Haner, David A..

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1999

Target Calibration: Retro-Reflection Mechanisms at 2 Micron

With the growing use of 2-micrometer eye-safe solid-state laser transmitters in coherent Doppler lidar applications, there is increased interest in the reflectance properties of hard target calibration materials at this wavelength. One of the factors to be considered is the polarization characteristic of the transmitter/receiver. The two fundamental lidar systems are either based upon the backscattering of linearly polarized or circularly polarized light. Consequently, the response of calibration materials to the particular state of polarization of the incident radiation is an important consideration. Ideally the calibration materials should have a similar reflectance response to that of the remote scattering medium that is being observed. Also the material should be most efficiently adapted to the polarization characteristics of the lidar system. There are two measurement parameters that are useful in presenting the characteristics of polarization of reflecting materials. The first is the linear polarization ratio: mu (sub l) =I (sub ol)/I (sub sl), where ol denotes opposite linear and sl denotes same linear. The second is circular polarization ratio: mu (sub c) = I (sub sc)/I (sub oc) where ol denotes opposite circular and sc denotes same circular. Notice that the ratios are inverted with respect to same polarization. It is the relative values of these polarization ratios that are used to characterize the retro-reflectance mechanism. Measurement of these parameters is conveniently obtained by using the Stokes vectors corresponding to the polarized backscatter at and near the retro-angle.

Haner, David A.↗
NASA NTRS1998

Bidirectional Reflectance Factors used in Lidar Calibration

Many atmospheric remote sensing applications of infrared lidar systems require that the backscatter signal be radiometrically calibrated. These systems are usually monostatic, consequently the reflected radiance from hard targets used in calibration will include the diffuse and the retroreflectance characteristics of the material. Radiometers which are part of orbiting sensors frequently contain onboard calibration subsystems. The onboard calibrator often utilizes onboard reflectance panels which are deployed at particular orbital locations to use the reflected sun light to calibrate the radiometers. To meet the need for correlative calibration of these remote sensing techniques a physically derived model could be used to extend the angular range and to improve the angular resolution of the measured reflectance properties of the calibration materials. A modified version of the B. Hake and E. Wells model has been adapted and will be described.

Haner, David A.↗
NASA NTRS1995

JPL-TMF multiwavelength aerosol lidar

The JPL-TMF Lidar Facility began operation in 1985 with the completion of a XeCl excimer based stratospheric ozone DIAL system. As an adjunct to this system a Nd:YAG based tropospheric ozone and aerosol system was assembled. The tropospheric ozone system was designed to utilize the fourth harmonic (266 nm) of the Nd:YAG to produce 289 nm, 294 nm or 299 nm by SRS in the isotopic hydrogen gases. The aerosol lidar was developed using the fundamental (1064 nm) and second harmonic of the Nd:YAG (532 nm). Following the eruption of Mount Pinatubo most of the effort was put into obtaining data on the layer structure of the volcanic aerosol as a function of altitude and time on a regular basis. During this period the tropospheric ozone DIAL was not employed on a regular schedule. The stratospheric measurements were of primary interest; however with the volcanic aerosol concentrated at the 16 - 26 km altitude the ozone concentration profile was perturbed. The aerosol interference in the ozone measurements caused the lidar community to seek techniques of measurement of the aerosol which could be used in making realistic corrections to the ozone measurements. It is generally accepted that a reasonable technique of measurement would include at least one channel of Raman scattering from a blue wavelength and a minimum of three other supporting wavelengths. With the primary transmitters available at TMF, a four wavelength system was considered for configuration. The four wavelength aerosol lidar is based on the Nd:YAG fundamental, the second and third harmonics of the transmitter. The receiver will separate these three wavelengths as well as the Raman scattering from atmospheric nitrogen of the third harmonic.

Haner, David A.↗
NASA NTRS1991

Differential absorption lidar systems for tropospheric and stratospheric ozone measurements

A lidar facility has been established at the Jet Propulsion Laboratory-Table Mountain Facility located at an altitude of 2300 m in the San Gabriel Mountains in Southern California. This facility is using the technique of differential absorption lidar to measure atmospheric ozone concentration profiles. Two separate systems are needed to obtain the profile from the ground up to an altitude of 45 to 50 km. An Nd:YAG-based system is described for measurements from the ground up to 15 to 20 km altitude, and an excimer-laser-based system for measurements from 15 km to 45 to 50 km altitude. The systems were designed to make high-precision, long-term measurements to aid in the detection of changes in the atmospheric ozone abundance through participation in the Network of Detection of Stratospheric Change.

Mcdermid, I. Stuart↗
NASA NTRS1990

Stimulated Raman shifting of the Nd:YAG fourth harmonic (266 nm) in H2, HD, and D2

The dependence of the first Stokes stimulated Raman conversion efficiency of fourth-harmonic radiation from a Nd:YAG laser at 266 nm has been studied for the isotopic species H2, HD, and D2 as a function of gas pressure and laser energy using a low numerical aperture (about 0.0045) pumping geometry. While the laser energy threshold for first Stokes conversion varies significantly among the species, photon conversion efficiencies of at least 50 percent can be achieved for all of them for laser pump energies at 266 nm of 50 mJ/pulse or less. This study provides a new measurement of the differential cross section for stimulated Raman scattering in HD of 8.1 + or - 2.4 x 10 to the -29th sq cm/sr at 266 nm and at high pressures, and agreement is found with previous measurements of the cross sections for H2 and D2. The results have been used to optimize the laser transmitter system for a differential-absorption lidar to measure tropospheric ozone concentration profiles.

Haner, David A.↗
NASA NTRS1989

Reflectance characteristics of reference materials used in lidar hard target calibration

Lidar hard target calibration is discussed, emphasizing the transfer target methodology. Characteristics of example calibratrion target surfaces are described in light of four reflectance mechanisms, specular, diffuse, retroreflection, and off-specular reflectance. The ideal transfer target is one which can be described as entirely diffusely reflecting, i.e., Lambertian. Correction for retroreflection is required when using the flowers of a sulfur transfer target at CO2 laser wavelengths. Corrections for specular and retroreflection for the integrating sphere are negligible; however, the off-specular reflectance of rough metal surfaces used in the integrating spheres is only qualitatively compared with the diffuse reflectance of flowers of sulfur.

Haner, David A.↗