Engineering topics
Hange, Craig E.
Publications and source records attributed to Hange, Craig E..
Aircraft Electric/Hybrid-Electric Power and Propulsion Workshop Perspective of the V/STOL Aircraft Systems Tech Committee
This presentation will be given at the AIAA Electric Hybrid-Electric Power Propulsion Workshop on July 29, 2016. The workshop is being held so the AIAA can determine how it can support the introduction of electric aircraft into the aerospace industry. This presentation will address the needs of the community within the industry that advocates the use of powered-lift as important new technologies for future aircraft and air transportation systems. As the current chairman of the VSTOL Aircraft Systems Technical Committee, I will be presenting generalized descriptions of the past research in developing powered-lift and generalized observations on how electric and hybrid-electric propulsion may provide advances in the powered-lift field.
Short Field Take-Off and Landing Performance as an Enabling Technology for a Greener, More Efficient Airspace System
The Cruise Efficient Short Take-Off and Landing (CESTOL) aircraft and Civil Tiltrotor (CTR) are two examples of powered-lift aircraft concepts that are of interest to NASA. These concepts will be able to utilize the shorter unused or underutilized runways and corresponding airspace at the crowded hub airports and many unused airfields and airspace that currently exist in other expanding urban areas providing additional capacity to the airspace system and reductions in congestion and delays seen in the current system. By treating the use of CESTOL and CTR as critical components that supplement other green aircraft to be used in the overall airspace system, the efficiency and improvements gained by the entire system will offset the potential increased fuel usage and emissions that may be a result of providing short field capability to the powered-lift aircraft. My presentation will address how NASA and the aerospace industry may identify, analysis, and finally implement these powered-lift aircraft into the airspace system and improve the capacity and reduce delay, while obtaining an overall reduction in noise, fuel usage, and emissions.
Temperature, Pressure, and Infrared Image Survey of an Axisymmetric Heated Exhaust Plume
The focus of this research is to numerically predict an infrared image of a jet engine exhaust plume, given field variables such as temperature, pressure, and exhaust plume constituents as a function of spatial position within the plume, and to compare this predicted image directly with measured data. This work is motivated by the need to validate computational fluid dynamic (CFD) codes through infrared imaging. The technique of reducing the three-dimensional field variable domain to a two-dimensional infrared image invokes the use of an inverse Monte Carlo ray trace algorithm and an infrared band model for exhaust gases. This report describes an experiment in which the above-mentioned field variables were carefully measured. Results from this experiment, namely tables of measured temperature and pressure data, as well as measured infrared images, are given. The inverse Monte Carlo ray trace technique is described. Finally, experimentally obtained infrared images are directly compared to infrared images predicted from the measured field variables.
Jet-induced ground effects on a parametric flat-plate model in hover
The jet-induced forces generated on short takeoff and vertical landing (STOVL) aircraft when in close proximity to the ground can have a significant effect on aircraft performance. Therefore, accurate predictions of these aerodynamic characteristics are highly desirable. Empirical procedures for estimating jet-induced forces during the vertical/short takeoff and landing (V/STOL) portions of the flight envelope are currently limited in accuracy. The jet-induced force data presented significantly add to the current STOVL configurations data base. Further development of empirical prediction methods for jet-induced forces, to provide more configuration diversity and improved overall accuracy, depends on the viability of this STOVL data base. The data base may also be used to validate computational fluid dynamics (CFD) analysis codes. The hover data obtained at the NASA Ames Jet Calibration and Hover Test (JCAHT) facility for a parametric flat-plate model is presented. The model tested was designed to allow variations in the planform aspect ratio, number of jets, nozzle shape, and jet location. There were 31 different planform/nozzle configurations tested. Each configuration had numerous pressure taps installed to measure the pressures on the undersurface of the model. All pressure data along with the balance jet-induced lift and pitching-moment increments are tabulated. For selected runs, pressure data are presented in the form of contour plots that show lines of constant pressure coefficient on the model undersurface. Nozzle-thrust calibrations and jet flow-pressure survey information are also provided.