Search NASA⌕ Search

Engineering topics

Hannon, F.

Publications and source records attributed to Hannon, F..

The Continuous Electron Beam Accelerator Facility at 12 GeV

This review paper describes the energy-upgraded Continuous Electron Beam Accelerator Facility (CEBAF) accelerator. This superconducting linac has achieved 12 GeV beam energy by adding 11 new high-performance cryomodules containing 88 superconducting cavities that have operated cw at an average accelerating gradient of 20 MV / m . After reviewing the attributes and performance of the previous 6 GeV CEBAF accelerator, we discuss the upgraded CEBAF accelerator system in detail with particular attention paid to the new beam acceleration systems. In addition to doubling the acceleration in each linac, the upgrade included improving the beam recirculation magnets, adding more helium cooling capacity to allow the newly installed modules to run cold, adding a new experimental hall, and improving numerous other accelerator components. We review several of the techniques deployed to operate and analyze the accelerator performance and document system operating experience and performance. In the final portion of the document, we present much of the current planning regarding projects to improve accelerator performance and enhance operating margins, and our plans for ensuring CEBAF operates reliably into the future. For the benefit of potential users of CEBAF, the performance and quality measures for the beam delivered to each of the experimental halls are summarized in the Appendix. Published by the American Physical Society 2024

43 PARTICLE ACCELERATORS↗

Generation and characterization of magnetized electron beam from a DC high voltage photogun for electron beam cooling application

One of the most challenging requirements for the proposed Electron-Ion Collider is the strong cooling of the proton beam, which is key to achieving the collider’s desired luminosity of order 10 33 -10 34 cm -2 s -1 . Magnetized bunched-beam electron cooling could be a means to achieve the required high luminosity, where strong cooling is accomplished inside a cooling solenoid where the ions co-propagate with an electron beam generated from a source immersed in a magnetic field. To increase the cooling efficiency, a bunched electron beam with high bunch charge and high repetition rate is required. This work describes the production and characterization of magnetized electron beam using a compact 300 kV DC high voltage photogun and bi-alkali antimonide photocathode. Beam magnetization was studied using a diagnostic beamline that includes viewer screens for measuring the shearing angle of the electron beamlet passing through a narrow upstream slit. Simulations and corresponding measurements of beam magnetization are presented as a function of laser spot size and magnetic field strength. Correlated beam emittance with magnetic field (0–0.15 T) at the photocathode was measured for various laser spot sizes. Measurements of photocathode lifetime were carried out at different magnetized electron beam currents up to 28 mA, and bunch charge up to 0.7 nC (not simultaneously).

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

USING E-BEAM IRRADIATION BEAMLINE AT JEFFERSON LAB TO REMOVE 1,4-DIOXANE AND PFAS IN WASTEWATER

The designed e-beam irradiation beamline [1] at Jefferson Lab has been commissioned and applied to study the degradation removal of 1,4-dioxane and per- and polyfluoroalkyl substances (PFAS) in wastewater by collaborating with Hampton Roads Sanitation District (HRSD), treating wastewater in southeast Virginia. The absorbed dose and dose distribution in the entire sample were achieved innovatively using Monte-Carlo simulations that were calibrated with opti-chromic dosimeter rods directly exposed to the e-beam. This research could be a stepstone to the future MW compact SRF accelerator [2] for wastewater remediation.

Li, X.↗

Beamline for E-beam processing at UITF

Electron beam irradiation is a method that has shown a good potential to reduce several pollutants in wastewater. One of the main challenges towards wider adoption of this method is the need for compact, reliable, cost-effective, high-power accelerators. Jefferson Lab is working on the design and prototyping of accelerator components, based on superconducting radio-frequency (SRF) technology, aiming at accelerators for industrial applications. The LDRD project aimed at designing, procuring, installing, and commissioning a beamline at the Upgraded Injector Test Facility (UITF) accelerator to allow electron-beam irradiation studies of different materials, beginning with wastewater. The availability of such beamline allows exploring the ability of electron-beam radiation to reduce or eliminate so-called “forever chemicals” that can be found in wastewater or industrial sites. After successful commissioning, the beamline was used to irradiate wastewater samples with different concentrations of 1,4-dioxane, in collaboration with Hampton Roads Sanitation District (HRSD).

42 ENGINEERING↗

Photoinjector generation of high-charge magnetized beams for electron-cooling applications

Electron cooling offers a relatively simple scheme to enable high-luminosity collisions in future electron–ion and hadron colliders. Contemplated TeV-energy hadron colliders require relativistic (sub 100 MeV) high-charge [] electron beams with a specific transverse eigenemittance partition. This paper discusses the generation of high-charge ( nC) 40 MeV electron bunches with eigenemittance partition consistent with requirements associated with electron-cooling option for future electron–ion colliders. The supporting experiment was performed at the FAST facility at Fermilab. The data are compared with numerical simulations and the results discussed in the context of beam requirement for future electron–ion colliders.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Electron beam irradiation of 1,4 dioxane

Electron beam irradiation produces both, reducing and oxidizing species which facilitate the reduction of contaminants found in water and wastewater. To investigate the impact of electron beam on 1,4-dioxane, a widely used solvent which has been declared as a probable human carcinogen by the U.S. Environmental Protection Agency, a beamline was designed and commissioned at the Upgraded Injector Test Facility at Jefferson Lab. Here, wastewater samples can be irradiated with a beam energy up to 10 MeV and a beam current of up to 100 nA. Beam acceleration is achieved by two superconducting radio-frequency cavities cooled by liquid helium in a cryomodule. A beam spot with a diameter of ~5 cm was produced at the target location using a pair of raster coils. Electron beam irradiation studies were performed using 1,4-dioxane in two different matrices, de-ionized water and secondary effluent wastewater, and for two concentrations, 10 microg/L and 100 microg/L. The concentration of 1,4-dioxane after irradiation was measured as a function of dose.

Li, Xi↗

Photoinjector Generation of High-Charge Magnetized Beams for Electron-Cooling Applications

Electron-cooling offers a relatively simple scheme to enable high-luminosity collisions in future electron-ion and hadron colliders. Contemplated TeV-energy hadron colliders require relativistic (sub 100 MeV) high-charge [${\cal O}(\mbox{nC})$] electron beams with a specific transverse eigenemittance partition. This paper discusses the generation of high-charge ($Q\le 3.2$~nC) 40 MeV electron bunches with eigenemittance partition consistent with requirements associated with electron-cooling option for future electron-ion colliders. The supporting experiment was performed at the FAST facility at FermiLab. The data are compared with numerical simulations and the results discussed in the context of beam requirement for future electron-ion colliders.

43 PARTICLE ACCELERATORS↗

MAGNETIZED GRIDDED THERMIONIC ELECTRON SOURCE

A crucial part of achieving JLab's proposed electron ion collider (JLEIC) design luminosity is the application of electron cooling to reduce the ion emittance. One required cooling method is Bunched Beam Cooling (BBC). This cooling process requires beam characteristics that are difficult to achieve. In particular, a high current magnetized electron beam. Here we present a magnetized gridded cathode thermionic electron source, deigned and built by Xelera Research LLC as part of the DOE SBIR program, that could represent the correct technology to use in achieving BBC, as well as a beamline at JLab that will be used to characterize the source.

Stefani, M.↗

HIGH CURRENT HIGH CHARGE MAGNETIZED AND BUNCHED ELEC-TRON BEAM FROM A DC PHOTOGUN FOR JLEIC COOLER

A high current, high charge magnetized electron beam-line was developed for fast and efficient cooling of ion beams for the proposed Jefferson Lab Electron Ion Col-lider (JLEIC). In this paper, we describe recent achieve-ments that include the generation of picosecond-bunch magnetized beams at average currents up to 28 mA with exceptionally long photocathode lifetime, and independent demonstrations of magnetized beam with high bunch charge up to 700 pC at 10s of kHz repetition rates. In addition, a detailed description of an extremely stable and reliable fiber-based drive laser system that employs a gain-switched master oscillator is presented. These ac-complishments mark important steps toward demonstrat-ing the feasibility of a technically challenging JLEIC cooler design using magnetized beams

Adderley, P.↗

Design of a low-cost, compact SRF accelerator for flue gas and wastewater treatment

The treatment of flue gases from power plants and municipal or industrial wastewater using electron beam irradiation technology has been successfully demonstrated in small-scale pilot plants. The beam energy requirement is rather modest, of the order of few MeV, however the adoption of the technology at an industrial scale requires the availability of a high beam power, of the order of 1 MW, in a cost effective way. In this report we present the design of a compact superconducting accelerator capable of delivering a cw electron beam with a current of 1 A and an energy of 1 MeV. The main components are an rf-gridded thermionic gun and a conduction cooled beta= 0.5 elliptical Nb3Sn cavity with dual coaxial power couplers. An engineering and cost analysis shows that the proposed design would result in a processing cost competitive with alternative treatment methods.

43 PARTICLE ACCELERATORS↗

High voltage performance of a dc photoemission electron gun with centrifugal barrel-polished electrodes

The design and fabrication of electrodes for direct current (dc) high voltage photoemission electron guns can significantly influence their performance, most notably in terms of maximum achievable bias voltage. Proper electrostatic design of the triple-point junction shield electrode minimizes the risk of electrical breakdown (arcing) along the insulator-cable plug interface, while the electrode shape is designed to maintain <10 MV/m at the desired operating voltage aiming at little or no field emission once conditioned. Typical electrode surface preparation involves diamond-paste polishing by skilled personnel, requiring several weeks of effort per electrode. In this work, we describe a centrifugal barrel-polishing technique commonly used for polishing the interior surface of superconducting radio frequency cavities but implemented here for the first time to polish electrodes for dc high voltage photoguns. The technique reduced polishing time from weeks to hours while providing surface roughness comparable to that obtained with diamond-paste polishing and with unprecedented consistency between different electrode samples. We present electrode design considerations and high voltage conditioning results to 360 kV (~11 MV/m), comparing barrel-polished electrode performance to that of diamond-paste polished electrodes. Here, tests were performed using a dc high voltage photogun with an inverted-geometry ceramic insulator design.

30 DIRECT ENERGY CONVERSION↗

SRF Systems for the Jefferson Lab Electron Ion Collider (JLEIC)

We report on the development of new CW SRF systems for the colliding rings of a proposed electron-ion collider (EIC) at Jlab. Jefferson Lab is developing new strongly HOM-damped SRF cavities for the ion collider ring and a high-energy electron cooler at 952.6 MHz. The baseline design JLEIC will re-use the PEP-II 476 MHz cavities for the electron ring with a possible future upgrade to 952.6 MHz SRF cavities at a later date. We discuss the design optimization of the new high current cavities and compare options for the strong HOM damping required. A concept for a modular cryostat to house these various cavities will be shown, and an overview of the challenging high-level parameters will be presented. These designs and concepts may be useful in other high current storage rings and ERLs.

Rimmer, Robert↗