Search NASA⌕ Search

Engineering topics

Haridas, Ravi Sankar

Publications and source records attributed to Haridas, Ravi Sankar.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Experimental determination of critical resolved shear stress for strain-induced phase transformation

The current investigation reports the first attempt to measure the critical resolved shear stress to initiates strain-induced phase transformation in a three-dimensional polycrystalline aggregate using high-energy diffraction microscopy (HEDM). In situ tensile testing was performed on a Fe38.5Mn20Co20Cr15Si5Cu1.5 metastable alloy exhibiting transformation-induced plasticity (TRIP). Grains with a higher propensity for strain-induced phase transformation were tracked using HEDM. A sharp drop in grain specific stress, coinciding with the appearance of a new ε-hcp grain oriented relative to the parent γ-fcc phase, was taken as evidence of grain-specific stress required to trigger phase transformation. The highest resolved shear stress on the potential transformation systems was identified as the critical resolved shear stress (CRSS) for strain-induced phase transformation. For the studied metastable alloy, CRSS for transformation was determined to be 86±3 MPa which was very close to theoretical CRSS value determined using Schmid factor (89±12 MPa) compared to the value determined using Taylor factor (62±7 MPa).

Jain, Roopam↗
DOE OSTI2024

Aluminum/SmCo 5 composites for structural and magnetic applications

Metal-bonded magnetic composites (MBMCs) present a promising alternative to dense sintered magnets, particularly for intricate components. Compared to polymer-based bonded magnets, MBMCs have wider applicability in harsh environments. In this paper, we demonstrate a solid-state shear-based manufacturing technique to introduce localized magnetization into a paramagnetic aluminum matrix by embedding SmCo5 permanent magnet particles. Our magnetic composites display hard magnetic behavior with a coercivity of 13 kOe and a remanent magnetization of 4.32 emu/g. In addition to magnetization, we also report a 9% improvement in Young’s modulus. Despite the local temperature rise during processing, the magnetic phases didn’t decompose into unwanted phases, preserving the composite's hard magnetic properties. Creation of an interfacial metallurgical bond with the matrix ensured the suitability of the composites for structural applications. Our study investigates the mechanical, and functional properties of composites, paving the way for lightweight structural magnetic composites with a transformative potential in the aerospace, nuclear, and automotive applications. This work underscores the potential for further optimization and development to drive innovations in magnet and equipment design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Crafting Multifunctional Materials with Tailored Mechanical and Magnetic Properties by Solid-State Non-equilibrium Processing

Aluminum matrix composites hold promise for creating lightweight structural components with multifunctional properties. Nonetheless, achieving desired magnetic or electrical characteristics without compromising their fundamental mechanical properties presents a significant challenge. Here, in this study, we explore mechanical stir-based extrusion as a solid-state metalworking technique to develop fine-grained microstructures and highly refined metallic composites. Our study focuses on creating a SmCo 5 -reinforced aluminum matrix composite using solid stir extrusion (SSE) and assessing its microstructure, mechanical, and magnetic properties through a comprehensive suite of characterization tools, including x-ray diffraction, electron microscopy, and magnetometry. Our findings reveal that incorporating a small amount (3.76 wt.%) of SmCo 5 phase in a non-heat-treatable, non-magnetic aluminum alloy via SSE yields a composite that exhibits good hard magnetic characteristics with a large coercivity (H ci = 13.5 kOe) and improved mechanical properties. This study underscores non-equilibrium processing via solid-state high-speed stirring as a compelling method for crafting multifunctional materials with tailored mechanical and magnetic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Strength-conductivity synergy via lean alloy design: A study on novel solid stir extrusion of an Al-2Cu-0.1 Nb-0.15Zr (~wt.%) alloy

Aluminum alloys find wide applications in power and transmission cables, and electrical conductors due to their advantageous properties of high electrical conductivity, and lower cost per unit. However, the lower tensile strength compared to copper poses a challenge for the mechanical stability of aluminum-based cables. In this study, we addressed this issue by adopting a process-based alloy design approach, creating a lean alloy with a dilute composition of Al-2Cu-0.1 Nb-0.15Zr (~wt.%). Here, the alloy was processed using a friction stir based novel SolidStir® (SSE) technique, followed by low-temperature aging. The resulting aluminum wire exhibited improved strength (240 MPa) while simultaneously enhancing electrical conductivity (64%IACS). The study employed computational simulations (Thermocalc) and experimental techniques (differential scanning calorimetry and transmission electron microscopy) to thoroughly investigate the microstructure. Microstructural examinations revealed that the precipitation kinetics in SSE and SSE+aged conditions played a significant role in enhancing strength and electrical conductivity. These findings demonstrate the successful achievement of high strength and high electrical conductivity in aluminum wire through a lean alloy design approach.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Additive manufacturing of a metastable high entropy alloy: Metastability engineered microstructural control via process variable driven elemental segregation

Compositional paradigm shift in high entropy alloys (HEAs) provided new opportunities for microstructural engineering, whereas process control during laser powder bed fusion (LPBF) additive manufacturing (AM) enable fine microstructure tailoring. Metastability engineering in transformation induced plasticity (TRIP) HEAs by addition of minor alloying elements is an attractive strategy for fine microstructural tuning. This study explored in detail the microstructural evolution during LPBF AM of a metastable Fe 40 Mn 20 Co 20 Cr 15 Si 5 (at.%) dual phase HEA (CS-HEA). LPBF processing window for CS-HEA was established based on quantitative analysis and experiments. Based on melt pool overlap lack of fusion pores were observed at lower energy densities (J) of $\textit{J}$ ≤ 31.25 J/mm 3 and key-hole formation by melt pool destabilization in case of $\textit{J}$ ≥ 75 J/mm 3 . The microstructure of CS-HEA consists of metastable FCC-γ and HCP-ε phases; LPBF process parameters governed the final phase fraction in the alloy which has been correlated to metastability alteration of the high temperature γ phase. Final microstructural engineering was devised by LPBF process control which enabled cooling rate manipulation to guide Mn and Si segregation at the cell boundaries, thereby controlling the matrix metastability and final phase fraction. Additionally, high resolution transmission electron microscopy (TEM) revealed disparity in stacking fault morphology in CS-HEA with LPBF process variable alterations associated with local variations in chemical composition and stacking fault energy. Further, the phase evolution with process parameters also affected the nanomechanical behavior of the alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Synergy of tensile strength and high cycle fatigue properties in a novel additively manufactured Al-Ni-Ti-Zr alloy with a heterogeneous microstructure

Alloy design strategies in additive manufacturing (AM) to achieve grain refinement and terminal eutectic solidification have been introduced to engineer Al alloys having microstructural hierarchy and heterogeneity. Such alloy design strategies enable crack-free builds with an expanded AM processing window and pushed the strength limit in Al alloys. However, fatigue performance of Al alloys made by AM is restricted by the presence of process induced defects and its stochasticity. In this work, tensile and high cycle fatigue (HCF) behavior of a novel Al-Ni-Ti-Zr alloy with a heterogeneous microstructure is studied in the as-built condition, supplemented by detailed microstructural and mechanical characterization. Excellent strength-ductility synergy of 342 MPa and 16% failure strain achieved in the alloy was associated with the microstructural attributes that pertain to the novel alloy. Additionally, the alloy showed excellent HCF performance with a fatigue endurance limit to ultimate tensile strength ratio of 0.29 in flexural fatigue mode. The study revealed the existence of multiple crack retardation mechanisms and favorable crack propagation pathways through the fine-grained regions which enabled good fatigue performance to the alloy. Further, a probabilistic model has been used to estimate the fatigue life of the alloy as a function of the stochastic microstructure by utilizing the statistical distribution of pores, solid-state inclusions, and grains in the AM Al alloy. Finally, the model parametric trends are consistent with the experimental observations.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Additive friction stir deposition of SS316: Effect of process parameters on microstructure evolution

Solid state nature of additive friction stir deposition (AFSD) additive manufacturing process is very advantageous in terms of defect formation and microstructural refinement in the material. Current study presents the process optimization, microstructural evolution and kinetics of recrystallization for AFSD deposited low stacking fault energy material - SS316. As deposited microstructure shows equiaxed ultra fine grains with an average grain size of ~5.0 ± 0.5 μm. Shear deformation at high temperature during processing leads to the operation of restoration mechanisms. Observation of necklace type microstructure in the as deposited SS316 is attributed to discontinuous dynamic recrystallization during processing. Recrystallization kinetics of the AFSD SS316 is characterized using Johnson-Mehl-Avarami-Kolmogorov (JMAK) model. Deformation – thermal cycling during AFSD process resulted in inconsistent recrystallization kinetics. Variation in strain, strain rate and temperature during processing with processing parameters result in varying microstructure and tool wear. Further, high strength-ductility combination and sustained work hardening in as deposited SS316 appear to arise from transformation and twinning during deformation, leading to the formation of hierarchical twins and martensitic phase after deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Excellent ballistic impact resistance of Al 0.3 CoCrFeNi multi-principal element alloy with unique bimodal microstructure

Multi-principal element alloys represent a new paradigm in structural alloy design with superior mechanical properties and promising ballistic performance. Here, the mechanical response of Al 0.3 CoCrFeNi alloy, with unique bimodal microstructure, was evaluated at quasistatic, dynamic, and ballistic strain rates. The microstructure after quasistatic deformation was dominated by highly deformed grains. High density of deformation bands was observed at dynamic strain rates but there was no indication of adiabatic shear bands, cracks, or twinning. The ballistic response was evaluated by impacting a 12 mm thick plate with 6.35 mm WC projectiles at velocities ranging from 1066 to 1465 m/s. The deformed microstructure after ballistic impact was dominated by adiabatic shear bands, shear band induced cracks, microbands, and dynamic recrystallization. The superior ballistic response of this alloy compared with similar Al x CoCrFeNi alloys was attributed to its bimodal microstructure, nano-scale L1 2 precipitation, and grain boundary B2 precipitates. Deformation mechanisms at quasistatic and dynamic strain rates were primarily characterized by extensive dislocation slip and low density of stacking faults. Deformation mechanisms at ballistic strain rates were characterized by grain rotation, disordering of the L1 2 phase, and high density of stacking faults.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Additively manufactured novel Al-Cu-Sc-Zr alloy: Microstructure and mechanical properties

An in-depth understanding of microstructure and resultant properties is paramount in the design of a novel alloy system, especially for additive manufacturing (AM). The present investigation aims to characterize a prototypical AM Al alloy with great potential for structural applications. An Al-1.5Cu-0.8Sc-0.4Zr alloy designed using integrated computational material engineering was printed using the laser powder bed fusion AM process. This novel alloy shows promising combination of strength and ductility in as-built and peak-aged conditions. This improvement in the tensile properties is attributed to the presence of both coherent L1 2 Al 3 Sc/Al 3 (Sc,Zr) precipitates and Cu-rich regions. The microstructures were studied via extensive microscopy at different length scales using X-ray microscopy, scanning electron microscopy, and transmission electron microscopy. Fractography revealed that the columnar grain boundaries in as-built condition allow easy slip transfer as compared to the equiaxed grains, with the apex of the melt pool acting as the crack nucleation site. Furthermore, the peak aged condition resulted in improved strength while marginally sacrificing ductility due to precipitates decorating dislocations, grain boundaries and melt pool boundaries thus acting as obstacles to slip transfer.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Notch-tensile behavior of Al0.1CrFeCoNi high entropy alloy

Notch-tensile behavior of an Al0.1CrFeCoNi high entropy alloy (Al0.1-HEA) was studied using V-notch geometry and with local strain mapping using digital image correlation (DIC). A notch-strength ratio of 1.51 indicated notch strengthening. Further analysis of stress-strain response supplemented with microstructural analysis revealed that, while the presence of notch results in strengthening due to work hardening by twinning induced plasticity, the notch also contributes strongly to geometrical softening in the non-uniform ductility regime, and accounts for the onset of failure. The strain localization behavior of Al0.1-HEA due to the presence of V-notch was compared with three conventional alloys: Inconel 625 nickel-based superalloy, 304 stainless steel and Ti–6Al–4V titanium alloy. The study revealed that the nature of notch widening with increasing strain was dependent on material characteristics. The extent of notch widening impacted the local strain field and stress distribution, thereby influencing the propensity for crack initiation and growth. The experimental results were verified by finite element analysis.

Sinha, Subhasis↗